Ridgid 456 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung fĂŒr Ridgid 456 (1 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂŒr 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/1
La cintreuse 456 Tri-Bender sert au cintrage des tubes recuits Ø 1/4",
5/16" et 3/8".
Le port systĂ©matique de lunettes de sĂ©curitĂ© s’im-
pose afin de limiter les risques de blessure oculaire.
Utilisation générale
1. Relevez la poignée de cintrage afin de positionner le tube dans la
rainure appropriée de la poignée à galet. Assurez-vous que le tube
s’engage bien dans la bride
(Figure 1)
.
2. Rabattez la poignĂ©e de cintrage jusqu’au tube, puis fermez-la contre
la poignĂ©e de gabarit jusqu’à ce que le repĂšre « 0 » de la poignĂ©e
de cintrage s’aligne sur le repĂšre d’angle de cintrage appropriĂ© de la
poignée à galet
(Figure 2)
.
Figure 1 Figure 2
RepĂ©rage de l’axe de cintrage par
rapport à un élément donné (embout
de tuyau, coude, etc.)
Coudes à 90°
‱ RepĂ©rez l’axe de cintrage (X) en marquant le tube Ă  la distance
voulue d’un Ă©lĂ©ment existant (embout de tuyau, coude, etc.). Ceci
donnera l’axe de la partie coudĂ©e du tuyau.
‱ Positionnez le tube dans la cintreuse comme indiquĂ© Ă 
l’article 1
.
‱ Si l’élĂ©ment existant se trouve Ă  la du repĂšre tracĂ© sur le tubegauche
(Figure 3 – Avant)
, alignez le repÚre sur la ligne « L» de la poignée
de cintrage.
‱ Si l’élĂ©ment existant se trouve Ă  la droite du repĂšre tracĂ© sur le tube
(Figure 4 – Avant)
, alignez le repÚre sur la ligne « » de la poignéeR
de cintrage.
Figure 3 – Avant (Before) Figure 3 – Aprùs (After)
Ridge Tool Company/Elyria, Ohio, U.S.A.
6/09
Printed in U.S.A. 999-998-655.10
456 Tri-Bender Instruction Sheet
‱ Align the mark on the tube with the unlabeled line on the shoe han-
dle
(see Figure 5)
.
Figure 5 – Before Figure 5 – After
‱ With the mark on the tube appropriately aligned, move the shoe
handle so that the “0” line aligns with the 45 degree line on the form
handle.
If you have any question concerning this Ridge Tool product:
‱ Contact your local RIDGID distributor.
‱ Visit www.RIDGID.com or www.RIDGID.eu to find your local Ridge
Tool contact point.
‱ Contact Ridge Tool Technical Services Department at techser-
vices@ridgid.com, or in the U.S. and Canada call (800) 519-3456.
The 456 TR-Bender is used to bend 1/4", 5/16" and 3
/8" soft tubing.
Always wear safety glasses to reduce the risk of eye
injury.
General Use
1. Rotate the shoe handle out of the way and position the tube in the
appropriate groove in the form handle. Be sure that the tube
engages the tube latch
(Figure 1).
2. Rotate the shoe handle into contact with the tube, and rotate the
shoe handle around the form handle so that the “0” line on the
shoe handle aligns with the desired degree of bend on the form
handle
(Figure 2)
.
Figure 1 Figure 2
Measured Bends Relative to Other
Features (Tube ends, Bends, etc.)
For 90° Bends:
‱ Mark the tube at the desired distance (X) from the feature (end of
tube, bend, etc.). The center of the leg of the bend will be this dis-
tance from the feature.
‱ Place the tube in the bender as described in
Step 1
above.
‱ If the feature is to the LEFT of the mark
(see Figure 3 – Before),
align the mark on the tube with the “ ” line on the shoe handle.L
‱ If the feature is to the RIGHT of the mark
(see Figure 4 – Before)
,
align the mark on the tube with the “ ” line on the shoe handle.R
Figure 3 – Before Figure 3 – After
Figure 4 – Before Figure 4 – After
‱ With the mark on the tube appropriately aligned, move the shoe
handle so that the “0” line aligns with the 90 degree line on the form
handle.
(See Figures 3 and 4 – After).
For 45° Bends:
‱ Mark the tube at the desired distance (X) from the feature (end of
tube, bend, etc.). The center of the arc segment will be this distance
from the feature.
‱ Place the tube in the bender as described in
Step 1
above.
Shoe
Handle
Tube
Latch
Form
Handle
Mark On
Tube
XX
Mark On
Tube
X
L Line
R Line
X
Mark On
Tube
XUnlabeled
Line X
WARNING
Cintreuse 456 Tri-Bender : Mode d’emploi
AVERTISSEMENT
Shoe Handle – PoignĂ©e de cintrage
Tube Latch – Bride
Form Handle – PoignĂ©e Ă  galet
L Line – Ligne L
Mark On Tube – Repùre du tube


Produktspezifikationen

Marke: Ridgid
Kategorie: Nicht kategorisiert
Modell: 456

Brauchst du Hilfe?

Wenn Sie Hilfe mit Ridgid 456 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Ridgid

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂŒr -Kategorien-