Ridgid 358 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Ridgid 358 (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
Ridge Tool Co., Elyria, Ohio, U.S.A.
9/08
Printed in U.S.A. 999-998-365.10
Pre-Cut Tube To Correct
Length
1. Add all blueprint center to center dimen-
sions for the total tube length. Mark tube at
this total length.
(Figure 1)
2. Because most blueprints are dimensioned
as though all corners were square, less
tube is actually required than the total of
the blueprint dimensions. Therefore,
REDUCE the total length by the number of
bends, using the Gain Scales on the
Swinging Arm.
(See Figure 2)
3. Reduce the measured length of tube from
Step 1 by one graduation for each 90˚ bend
using the scale marked “90˚ Gain”. Reduce
Length of tube by one graduation for each
45˚ bend using the scale marked “45˚ Gain”.
(See Figure 2)
Mark tube and cut.
Figure 1
A + B + C + D = Total Length
A
B
D
C
45˚
90˚
90˚
Swinging Arm
Rollshaft
Roll
Drive Arm
Tube
2 - 90˚ Bends
Gain
Total Length
Latch
Form
Handle
Ratchet Handle
Figure 2
Instructions For Nos. 358, 368 and 378 Tube Benders
90˚ Bends
4. For first bend, measure from end of tube
and mark at blueprint dimension.
(Figure 3)
5. Raise Latch. Bring handles together to
release Drive Arm. Swing Drive Arm counter
clockwise until it stops. Move Swinging Arm to
clear opening between Form Handle & Roll.
6. Position tube in bender.
(Figure 4a)
If the
end from which you measured is in the Form
Handle, the measured mark should be
directly under the 90˚ mark on the Drive
Arm.
(Figure 4a)
If, however, the end from
which you measured is to the right (Not in
the Form Handle), set the mark on the tube
directly under the “R” on the Drive Arm.
(Figure 4b)
7. Close Latch over tube and Swinging Arm
over Roll Shaft.
8. To Ratchet - Pull Ratchet Handle away from
Form Handle. After each pull, Drive Arm will
remain locked due to the Holding pawl.
Actuate Ratchet Handle until pointer on
Swinging Arm is at 90˚. Because tubing has
a slight springback action, it may be neces-
sary to over bend slightly to allow tube to
spring back to 90˚.
9. To release Bender, follow Step 5.
10. If more than one bend is required, measure
from center line of the preceding bent leg
and mark tube to blueprint dimension
(See
Figure 5)
. Position tube in bender as out-
lined in Step 6.
11. For convenience, the Form Handle Clamping
Pad may be held in a vise.
45˚ Bends
12. For first bend, measure from end of tube
and mark at blueprint dimension.
13. Position tube in bender, as illustrated in
Figure 4 a-b
. When making a 45˚ bend, the
end from which you measured and marked
the tube may be either in the Form Handle
or to the right (Not in the Form Handle). In
either case, the mark on the tube should be
under the 45˚ mark on the Drive Arm.
14. Close Latch over tube. Move Swinging Arm
to engage Roll Shaft.
15. To Bend - Follow Step 8 until pointer on
Swinging Arm is at 45˚.
Ridge Tool Co., Elyria, Ohio, U.S.A.
Figure 3
A
Figure 4a
A
Latch Drive Arm Mark
Tube
Form
Handle
Ratchet
Handle
Figure 4b
A
Latch Drive Arm Mark
Tube
Form
Handle
Ratchet
Handle
A
Figure 5
Instructions For Nos. 358, 368 and 378 Tube Benders


Produktspezifikationen

Marke: Ridgid
Kategorie: Nicht kategorisiert
Modell: 358

Brauchst du Hilfe?

Wenn Sie Hilfe mit Ridgid 358 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Ridgid

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-