Revo RE16BNDL6-2000 Bedienungsanleitung

Revo Sicherheitskamera RE16BNDL6-2000

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung fĂŒr Revo RE16BNDL6-2000 (2 Seiten) in der Kategorie Sicherheitskamera. Dieser Bedienungsanleitung war fĂŒr 22 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
General Guidelines for Installing
Traditional Shutters
To deïŹ‚ect rain away from the structure, Louvered shutters
should be installed so the louvers face AWAY from the
structure when shutters are closed. (see diagram at right)
Shutters in closed position
Pick shutters to ïŹt window & put
next to each window on top of
saw horses to make sure shutters
are paired properly. Lay two
shutters face down next to each
and prepare to install hinges.
1
Position & install upper holdback
clips 1" from top & center edge
of stile. Shutters over 58" require
2 sets of acorns; install similarly
at top.
3
Install hinges after determining
offset. Hinges are to be set at
top & bottom even with outside.
Drill holes with 1/8th pilot bit.
Be careful not to drill all the way
through shutter.
2
Install slide bolt. Turn shutters
over & line-up slide bolt edge
with shutter edge (see diagram
at right). Pre-drill 1/8 slot hole
(careful not to drill all the way
through). Install slide bolt with
screws. Shutters are now ready
for installation.
4
Shutter A Edge Shutter B Edge
6
Install “S” Holdback*. Shutter is now
held open by acorn anchor. Position
shutter dog in correct location & mark
for screws & fasten to wall—1Âœ" down
from shutter & 1Ÿ" from outside edge.
*The acorn clip is better suited for holding the
shutters in place, and as such, the “S” Holdback
is recommended more for a decorative use as
opposed to a functional one.
7
Install acorn clip. Swing shutter open
& mark center of holdback clip &
install acorn clip into brick.
Beaded A beaded detail that is molded into the inside edge of the face of each stile.
Board Traditionally used on barns but ideal for more rustic homes. Authentic tongue & groove look with the front
and Batten & back of the shutter featuring the same beveled look as if the shutter were made of individual boards.
Flat Panel A solid shutter where the center portion of the shutter is recessed from the stiles
Shutter (i.e. Memphis style shutter).
Fixed Louvered Positioned the historically accurate way, the louvers are tilted in towards the wall when the shutter
Shutter is in the open position.
Leaf A single shutter or 1/2 pair.
Mousehole A notched hole in the rails that accommodated the ends of the tilt rod when the louvers were in
the closed position. Now it just adds to the authentic appearance.
Mullions The vertical element between the stiles that acts as a divider. Found in Bahama shutters.
Rabbeting Also called “shiplap", used on many functional shutters so that when closed the individual shutter leaves
ïŹt into one another.
Radius or A shutter which has a curved top.
Arched Top
Rails The horizontal crosspieces of a shutter (i.e. top rail, bottom rail, center rail).
Raised Panel A solid shutter where the center portion of the shutter panel protrudes outward from the surrounding
Shutter routed bevel.
Shutter Capping A metal (most usually copper) capping that was placed over the top edge of the shutter to prevent
water intrusion and the resulting wood rot. This capping is not necessary with Atlantic shutters as, due
to materials used, they are impervious to both water intrusion and rot.
Stiles The upright vertical sections of a shutter, which may be beaded or non-beaded.
Tilt Rod Working louvered shutters had a rod, or tilt-rod, to move the louvers into the open or closed position.
These are now purely decorative for those who truly desire the more authentic look.
Shutter Terminology
Position shutter in opening allowing
equal amounts of space between shutter
& wall (A & B), and between shutters
(C) to allow for smooth operation
[see diagram at right]. When attaching
the pintel to the structure you may
have to drill into mortar & brick—use
appropriate molly’s in mortar & brick.
5
A C B

Produktspezifikationen

Marke: Revo
Kategorie: Sicherheitskamera
Modell: RE16BNDL6-2000

Brauchst du Hilfe?

Wenn Sie Hilfe mit Revo RE16BNDL6-2000 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Sicherheitskamera Revo

Revo

Revo REHSPTZ30-1CM Bedienungsanleitung

7 April 2024
Revo

Revo REXN600-2 Bedienungsanleitung

29 MĂ€rz 2024
Revo

Revo REVDN600-1 Bedienungsanleitung

20 MĂ€rz 2024
Revo

Revo REVDN650-1 Bedienungsanleitung

28 Februar 2024
Revo

Revo RE16BNDL6-2000 Bedienungsanleitung

17 Februar 2024
Revo

Revo RETRT700-1 Bedienungsanleitung

20 November 2023

Bedienungsanleitung Sicherheitskamera

Neueste Bedienungsanleitung fĂŒr -Kategorien-

Speco Technologies

Speco Technologies O2PTZ34D5W Bedienungsanleitung

14 August 2024
ZKTeco

ZKTeco BL-34F26L Bedienungsanleitung

11 August 2024
Moxa

Moxa VPort 26 Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 36 Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 16-M12-CAM3L5436N Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 16-M12-CAM3L54160N Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort P06 Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPORT P06-1MP-M12-CAM80 Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 16-DO-M12-CAM3L5436N Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 26A-1MP Bedienungsanleitung

27 Juni 2024