RCA VH226F Bedienungsanleitung

RCA Lautsprecher VH226F

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für RCA VH226F (18 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war für 26 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/18

Programmable Antenna Rotator

VH226F User's Manual

Important Information

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s

instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug

has two blades with one wider than the other. A grounding type plug has two blades and a

third grounding prong. The wide blade or the third prong are provided for your safety. If

the provided plug does not ﬁt into your outlet, consult an electrician for replacement of the

obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12.Use only with the cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold with

the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to

avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

Care and Maintenance

• Always use a soft cloth to clean the speaker and transmitter. Never use any product containing alcohol

or other solvents as they may damage the surface.

• Use caution when plugging the power transformers in an AC outlet to avoid the risk of electric shock.

• If the speaker are used outside on a deck or patio, make sure you take them indoors in the event of a

rainstorm to prevent possible damage.

• Do not operate or store the system in extreme temperatures.

CAUTION: Please keep the unit in a good ventilation environment. Do not install the equipment

in a conﬁned space, such as a book case or similar unit.

For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and shall

be easily accessible.

Do not use this apparatus near water.

The apparatus shall not be exposed to dripping or splashing or placed near objects ﬁlled with

liquids.

No naked ﬂame sources, such as lighted candles, should be placed on the apparatus.

Only use attachments/accessories speciﬁed by the manufacturer.

Use only with the cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold

with the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

WARNING: Please refer the information on exterior bottom enclosure for electrical and safety

information before installing or operating the apparatus.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference, and 2) This device must accept any interference

received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communication. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modiﬁcations not expressly approved by VOXX Accessories Corporation

could void the user’s authority to operate the equipment.

Industry Canada Regulatory Information Avis d’Industrie Canada

CAN ICES-3 (B)/NMB-3 (B) CAN ICES-3 (B)/NMB-3 (B)

Product Information

Keep your sales receipt to obtain warranty parts and service and for proof of

purchase. Attach it here and record the serial and model numbers in case you

need them. These numbers are located on the product.

Model No.: ______________________________________________________________

Purchase Date: __________________________________________________________

Dealer/Address/Phone: ___________________________________________________

IMPORTANT SAFETY INSTRUCTIONS

PLEASE READ AND SAVE FOR FUTURE REFERENCE

This is class II equipment designed with double or reinforced insulation so it does

not require a safety connection to electrical earth (US: ground).

Plugging in for power AC OUTLET POWER SUPPLY: 100–240 V ~ 50/60 Hz

The AC power plug is polarized (one blade is wider than the other) and only ﬁts

into AC power outlets one way. If the plug will not go into the outlet completely,

turn the plug over and try to insert it the other way. If it still does not ﬁt, contact

a qualiﬁed electrician to change the outlet, or use a different one. Do not attempt

to bypass this safety feature.

Installing the Outdoor Drive

Unit

Step 1: Attach cable to the drive unit

1. Run cable (not included) to the drive unit.

IMPORTANT: Up to 150’ (46m) of 20AWG 3

conductor cable may be used. For longer runs, use heavier

gauge wire.

2. Unscrew the single screw on the bottom door. Swing

the door open.

3. Insert the cable through the grommet on the side of

the drive unit.

4. Separate the cable leads for 1.5”(4cm) and strip off

the insulation for 0.5”.

Unpacking

Make sure the following pieces are in the box:

(1) Drive unit

(1) Control unit

(1) Remote control

Hardware kit:

(2) U Bolts

(5) Rotor-Mounting Bolts

(3) Short Brackets

(1) Long Bracket (with guy-wire holes)

(10) Nuts

(8) Washers

Note: Bolts require a 10mm or adjustable wrench (not

included). continues on next page...

The MAINS plug is used as the disconnect device, the disconnect device shall

remain readily operable.

WARNING:

TO PREVENT FIRE

OR ELECTRICAL

SHOCK HAZARD, DO

NOT EXPOSE THIS

PRODUCT TO RAIN

OR MOISTURE.

5. Lower the drive unit onto the support mast until it

stops on the mast nose of the drive housing. Tighten

the nuts. Moderate tightening with a 10mm or

adjustable wrench will cause the teeth to grip the mast

securely.

Side of the drive unit

Support mast

Mast nose

Step 2: Mount the drive unit

If you’re not mounting the unit inside a tower, you’ll need

to mount it to a separate mast (not included). This kit

comes with the necessary hardware for mounting.

CAUTION: Select a mounting location where the

antenna cannot come in contact with power lines while it

is being installed, and where the installation will not fall

across power lines if a guy wire should fail.

1. Screw four nuts onto four rotor-mounting bolts.

Screw each nut all the way to the head of each bolt.

Then put one washer on each of the bolts, next to the

nut.

2. Place a short bracket over two of the bolts, with the

ﬂat section of the bracket snug against the washerless

nuts. Place the long bracket over the other two bolts

the same way.

3. Screw the short bracket/bolt assembly into the top

two holes on the side of the drive unit base. Screw the

long bracket/bolt assembly into the bottom two holes.

Screw each bolt as far as it will go into the drive unit.

5. Find the silver- or wide-jacketed lead and connect

it to pin (1). Connect the adjacent lead to pin (2).

Connect the third lead to pin (3). If 4-wire cable is

used, connect both wire 3 and 4 to pin (3).

IMPORTANT: Make sure there are no loose strands

which can short between terminals.

6. Doublecheck the wiring order. Close the door and

screw it back into place.

Bolt

Nut

Short Bracket

Side of the drive unit

IMPORTANT: To avoid moisture collecting in the cable

make sure the cable jacket passes thru the grommet.

Bottom of the drive unit

Bottom door

Grommet

(1)(2)(3)

Behind the door

Terminals:

Silver (or wide) wire (red) to pin (1)

Second wire (black) to pin (2)

Third wire (green) to pin (3)

4. Position the brackets and nuts/washers so that they

leave just enough room for the support mast to go

through.

Washer

Long Bracket

IMPORTANT: Do not overtighten to the point that

you deform the mast, since this will reduce its strength.

The drive unit is designed for 1.25” diameters but will

accommodate up to 2” diameter support masts.

6. (Optional) Attach guy wires (not included) to the

holes in the bottom bracket.

Installing and Programming

the Indoor Control Unit

Step 1: Set up to the control unit

1. Determine the length of cable needed to run between

the outdoor and indoor units. Cut the cable to that

length.

2. Strip about 1/2” of the jacket off the end of each wire.

3. Insert each bare wire into the connector plate on the

control unit’s back panel as shown below.

4. Release jacket to secure on connector.

IMPORTANT: The unit must be wired correctly.

Damage can result from improper wiring.

5. Plug power cord of the control unit into an AC outlet.

6. Turn on the unit by putting the switch on the right

side of the control unit in the on position.

The MEMORY display on the front panel reads 0,

and the display reads DEGREE X 10 00.

1/ 2"

3 wire (green) #3 to #3

2 wire (black) #2 to #2

1 wire (red) #1 to #1

7. Attach the lead-in cable to the support mast

with cable tie/stand-off insulators (not included)

approximately every four feet.

8. Tape the rotator control cable directly to the support

mast.

Step 3: Install the antenna/cable

1. Insert the 2 U-bolts through the back of the rotor

section of the drive unit.

2. Place the remaining 2 brackets over the ends of the

U-bolts.

3. Put a washer and nut on the very end of the U-bolts

to keep the brackets in place.

4. Position the brackets and nuts/washers so that they

leave just enough room for the antenna mast to go

through.

Note: Use no more than 3 feet of antenna mast between

the rotor and the antenna itself.

5. Lower the antenna mast between the brackets and the

rotor. Tighten the nuts. Moderate tightening with a

10mm or adjustable wrench will cause the teeth to

grip the mast securely.

Antenna

Cable tie/stand-off

Loop to allow full

turn of antenna

Drive unit

Control cable

Cable tie/stand-off

Tape to mast

Antenna lead-in cable

Support mast

123

Side of the drive unit

U-Bolt

Nut

Bracket

Washer

6. After connecting the antenna lead-in cable to the

antenna, fasten it to the antenna mast using cable tie/

stand-off insulators or electrical tape (not included) as

shown. Provide a generous loop at the drive unit.

Antenna mast

(3 foot max)

Produktspezifikationen

Marke:	RCA
Kategorie:	Lautsprecher
Modell:	VH226F

Brauchst du Hilfe?

Wenn Sie Hilfe mit RCA VH226F benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Lautsprecher RCA

RCA VH226F Bedienungsanleitung

14 Juli 2024

RCA SP10 Bedienungsanleitung

4 Juli 2024

Bedienungsanleitung Lautsprecher

Neueste Bedienungsanleitung für -Kategorien-

Sonance Visual Performance VP65 SST Bedienungsanleitung

16 Oktober 2024

Bowers And Wilkins CWM664 Bedienungsanleitung

16 Oktober 2024

Focal Chorus 826 V Bedienungsanleitung

16 Oktober 2024

KEF Ci200ER Bedienungsanleitung

16 Oktober 2024

Steren SPK-1100BL Bedienungsanleitung

16 Oktober 2024

Aiwa SP-A100 Bedienungsanleitung

16 Oktober 2024

Trust GXT 628 Bedienungsanleitung

15 Oktober 2024

Pyle PBMSPG6 Bedienungsanleitung

15 Oktober 2024

Marshall Tufton Bedienungsanleitung

15 Oktober 2024

Sunstech SPUBT780 Bedienungsanleitung

15 Oktober 2024