Raymarine M81126 Constant Running Hydraulic Pump Bedienungsanleitung

Raymarine Marine M81126 Constant Running Hydraulic Pump

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Raymarine M81126 Constant Running Hydraulic Pump (18 Seiten) in der Kategorie Marine. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/18

Constant

Running

Hydraulic

Pump

Installation Guide

Document Number: 87039-2

Date: March 2006

87039_2.fm Page 1 Wednesday, April 9, 2014 2:56 PM

2 CR Hydraulic Pump - Installation Guide

Important information

Drives covered

M81126 - Raymarine Constant Running Pump (Variable flow) 12V

M81128 - Raymarine Constant Running Pump (Variable flow) 24V

Safety notices

WARNING: Product installation

This equipment must be installed and operated in accordance

with the instructions contained in this handbook. Failure to do so

could result in poor product performance, personal injury and/or

damage to your boat.

Because correct performance of the boat’s steering is critical for

safety, we STRONGLY RECOMMEND that an Authorized Raymarine

Service Representative fits this product.

WARNING: Navigation aid

Although we have designed this product to be accurate and

reliable, many factors can affect its performance. As a result, it

should only be used as an aid to navigation and should never

replace commonsense and navigational judgement. Always

maintain a permanent watch so you can respond to situations as

they develop.

EMC installation guidelines

All Raymarine equipment and accessories are designed to the best industry

standards for use in the recreational marine environment.

Their design and manufacture conforms to the appropriate Electromagnetic

Compatibility (EMC) standards, but correct installation is required to ensure that

performance is not compromised. Although every effort has been taken to ensure

that they will perform under all conditions, it is important to understand what

factors could affect the operation of the product.

The guidelines given here describe the conditions for optimum EMC performance,

but it is recognized that it may not be possible to meet all of these conditions in all

situations. To ensure the best possible conditions for EMC performance within the

constraints imposed by any location, always ensure the maximum separation

possible between different items of electrical equipment.

For optimum EMC performance, it is recommended that wherever possible:

87039_2.fm Page 2 Wednesday, April 9, 2014 2:56 PM

Raymarine equipment and cables connected to it are:

• At least 3 ft. (1 m) from any equipment transmitting or cables carrying radio

signals e.g. VHF radios, cables and antennas. In the case of SSB radios, the dis-

tance should be increased to 7 ft. (2 m).

• More than 7 ft. (2 m) from the path of a radar beam. A radar beam can nor-

mally be assumed to spread 20 degrees above and below the radiating ele-

ment.

The equipment is supplied from a separate battery from that used for engine start.

Voltage drops below 10 V, and starter motor transients, can cause the equipment

to reset. This will not damage the equipment, but may cause the loss of some

information and may change the operating mode.

Raymarine specified cables are used. Cutting and rejoining these cables can

compromise EMC performance and must be avoided unless doing so is detailed in

the installation manual.

If a suppression ferrite is attached to a cable, this ferrite should not be removed. If

the ferrite needs to be removed during installation it must be reassembled in the

same position. Always use the ferrites supplied by Raymarine.

Connections to other equipment

If your Raymarine equipment is to be connected to other equipment using a cable

not supplied by Raymarine, a suppression ferrite MUST always be attached to the

cable near to the Raymarine unit.

Waste Electrical and Electronic Equipment Directive

The Waste Electrical and Electronic Equipment (WEEE) Directive

requires the recycling of waste electrical and electronic equipment.

Whilst the WEEE Directive does not apply to some of Raymarine’s

products, we support its policy and ask you to be aware of how to

dispose of this product. The crossed out wheelie bin symbol, illustrated above,

and found on our products sigifies that this product should not be disposed of in

general waste or landfill. Please contact your local dealer, national distributor or

Raymarine Technical Services for information on product disposal.

87039_2.fm Page 3 Wednesday, April 9, 2014 2:56 PM

Produktspezifikationen

Marke:	Raymarine
Kategorie:	Marine
Modell:	M81126 Constant Running Hydraulic Pump

Brauchst du Hilfe?

Wenn Sie Hilfe mit Raymarine M81126 Constant Running Hydraulic Pump benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage