Quantum DLT-V4 Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Quantum DLT-V4 (28 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 56 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/28
DLT-V4 Tape Drive
Quick Start Guide
English- - - - - - - - - - - 1
German - - - - - - - - - - 5
Spanish - - - - - - - - - - 9
French - - - - - - - - - - 13
Japanese - - - - - - - - 17
Korean - - - - - - - - - - 21
Simplified Chinese - 25
Introduction 0
This guide provides instructions on how to configure and install the DLT-V4 tape
drive in the following configurations:
•Internal Tape Drive — SCSI, SATA, and USB versions
•Tabletop Tape Drive — SCSI and USB/eSATA versions
Internal Tape Drive 0
1Inspect the shipping box and contents of the box for damage. If you find any
damage, report it to the shipping company.
2Select a server or workstation to host the tape drive.
3Download the device driver from the following Web site:
http://www.quantum.com/ServiceandSupport/
SoftwareandDocumentationDownloads/DLTV4/Index.aspx.
4Shut down and power off the host and all peripheral devices attached to the
selected host.
5 SCSI Tape Drives Only — If necessary, change the SCSI ID using the SCSI
jumpers (see figure 1). (For complete instructions, see the DLT-V4 Product
Manual.)
NOTE:See the last page of this document for additional resources.
NOTE:Save the packing materials in case you need to move or ship the
tape drive. You must ship the tape drive in the original or equivalent
packing materials to preserve your warranty.
NOTE:The factory default SCSI ID is .5
DLT-V4 Tape Drive Quick Start Guide
2
Figure 1 Setting the SCSI ID
6Remove the cover from the server or workstation as
described in the server or workstation’s documentation.
See figure 2.
7 SCSI Tape Drives Only — If necessary, install an LVD/SE
host bus adapter in the server or workstation.
8 SCSI Tape Drives Only — Connect an active LVD/SE
terminator onto one end of the SCSI cable, if the tape
drive is the last or only device on the SCSI bus (see
figure 2). If the SCSI cable that came with the SCSI host
bus adapter already has a terminator built into it, do
not use an additional terminator.
Figure 2 Removing the Cover,
Installing, and Terminating
9 SCSI Tape Drives Only —Connect the SCSI cable to the
tape drive and to the SCSI host bus adapter. Connect
the power cable to the tape drive (see figure 3).
NOTE:If the tape drive is not the last or only device
on the SCSI bus, make sure the last device on
the SCSI bus is properly terminated is and
powered on whenever you use the tape drive.
SCSI ID jumpers
Figure 3 Connecting the SCSI
Cables to Rear of Tape Drive
10 SATA Tape Drives Only — Connect one end of the
SATA data cable to the tape drive and the other end of
the SATA data cable to the SATA host bus adapter (see
figure 4).
11 SATA and USB Tape Drives Only — Connect either the
SATA power cable drive power cable to the tape or
drive (see figure 4).
Figure 4 Connecting the SATA
Cables to Rear of Tape Drive
12 Secure the tape drive in the selected server or
workstation with the appropriate M3 mounting screws
(see figure 5). Contact the computer manufacturer if
the server or workstation uses mounting rails for
internal tape drives.
CAUTION:Connect only one power cable to the
drive. Connecting both the SATA power cable
and drive power cable to the tape drive may
damage the drive.
SCSI cable (with terminator)
Drive power cable
SATA
power
cable
SATA
data
cable
Drive
power
cable
Install EITHER
(not both)
DLT-V4 Tape Drive Quick Start Guide
3
13 USB Tape Drives Only — You must use a SATA data
cable and a SATA-to-USB adapter. Please follow the
installation instructions in the SATA-to-USB Adapter
Installation Guide included with the adapter (also
located on the resource CD.
Figure 5 Securing the Tape
Drive
14 Install the cover on the server or workstation. Connect
the power cables to any attached peripheral devices.
15 Power on any attached peripheral devices.
16 Power on the server or workstation and allow its
operating system to start.
Tabletop Tape Drive 0
1Inspect the shipping box and contents of the box for
damage. If you find any damage, report it to the
shipping company.
2 SCSI Tape Drives Only — If necessary, change the SCSI
ID for the tape drive. Use a small screwdriver or
ballpoint pen to press the buttons above or below the
SCSI ID to increase or decrease the number (see
figure 6). (For complete instructions, see the DLT-V4
Product Manual.)
Figure 6 Changing the SCSI ID
3Select a location near the server or workstation that will
host the tape drive.
NOTE:Save the packing materials in case you need
to move or ship the tape drive. You must ship
the tape drive in the original or equivalent
packing materials to preserve your warranty.
4Download the device driver from the following Web
site: http://www.quantum.com/ServiceandSupport/
SoftwareandDocumentationDownloads/DLTV4/
Index.aspx.
5Shut down and power off the host and all peripheral
devices attached to the selected host.
6 SCSI Tape Drives Only — If necessary, install an LVD/SE
host bus adapter in the server or workstation (see
figure 7).
7 SCSI Tape Drives Only — Connect the SCSI cable to the
tape drive and to the SCSI host bus adapter — or to the
previous device on the SCSI bus (see figure 7).
8 SCSI Tape Drives Only — Connect an active LVD/SE
terminator onto one end of the tape drive, if it is the
last or only device on the SCSI bus (see figure 7).
Figure 7 Connecting the Cables
— SCSI Tape Drive
NOTE:If the tape drive is not the last or only device
on the SCSI bus, make sure the last device on
the SCSI bus is properly terminated and is
powered on whenever you use the tape drive.
LVD/SE host bus
adapter
SCSI cable
Off
On
Terminator
SCSI cable


Produktspezifikationen

Marke: Quantum
Kategorie: Nicht kategorisiert
Modell: DLT-V4
Produkttyp: Speicherlaufwerk
Produktfarbe: Schwarz
Betriebstemperatur: 10 - 40 °C
Relative Luftfeuchtigkeit in Betrieb: 20 - 80 %
Stromverbrauch (Standardbetrieb): 20 W
Eingebaut: Ja
Energiebedarf: 120/240 VAC
Netzteiltyp: +5/+12 VDC
Schnittstelle: SATA 1.0, 160 SCSI, USB 2.0
Mittlere Betriebsdauer zwischen Ausfällen (MTBF): 250000 h
Höhe bei Betrieb: -152.4 - 9144 m
Durchsatz: 20 MB/s
Laufwerk, Puffergröße: 32 MB
Zugriffzeit: 84 ms
Medientyp: Bandkartusche
Kompression Verhältnis: 2:1
Kapazität ohne Komprimierung: 160 GB
Kapazität (komprimiert): 320 GB
Datenspeichertyp: DLT
Burst-Ăśbertragungsrate: 1600 MB/s
Aufzeichnungsdichte: 219 kBit/Zoll
Spurdichte: 352
Backup-Leistung mit Komprimierung: 72 GB/h

Brauchst du Hilfe?

Wenn Sie Hilfe mit Quantum DLT-V4 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Quantum

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-