QSC SC-2150 Bedienungsanleitung

QSC Lautsprecher SC-2150

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für QSC SC-2150 (7 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war für 23 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/7
TD-001624-01-A
*TD-001624-01*
SC-2150
Quick Start Guide
SC-2150 Screen Channel Loudspeaker System
®
2
TD-001624-01-A
EXPLANATION OF SYMBOLS
The term
“WARNING!”
indicates instructions regarding personal safety. If the instructions are not followed the result may be bodily injury or death.
The term
“CAUTION!”
indicates instructions regarding possible damage to physical equipment. If these instructions are not followed, it may result
in damage to the equipment that may not be covered under the warranty.
The term “IMPORTANT!” indicates instructions or information that are vital to the successful completion of theprocedure.
The term
"NOTE"
is used to indicate additional useful information.
The intent of the exclamation point within an equilateral triangle is to alert the user to the presence of important safety, and
operating and maintenance instructions in this manual.
IMPORTANT SAFETY INSTRUCTIONS_____
Refer to TD-000142 Safety Precautions contained in the shipping carton.
Warranty
For a copy of the QSC Limited Warranty, visit the QSC website at www.qsc.com
Introduction
The SC-2150 is a 3-way, selectable passive full-range or bi-amplified screen channel loudspeaker system comprised of two main units. These
units are shipped in separate cartons.
DCS-2150-HF Mid-High Frequency Loudspeaker System
Part Quantity
DCS-2150-HF Loudspeaker System 1
Wiring Harness *
TD-000142 Safety Precautions 1
TD-000453 Warranty 1
* Part of the HF Loudspeaker System
DCS-2150-LF Low-Frequency Enclosure
Part Quantity
DCS-2150-LF Loudspeaker Enclosure 1
Hex-head Screw 3
Flat Washer 3
Split Washer 3
TD-000142 Safety Precautions 1
TD-000453 Warranty 1
— Figure 1 —
DCS-2150-HF
DCS-2150-LF
3
TD-001624-01-A
Assemble the SC-2150
This procedure assumes that both items and associated hardware is unpacked and the two
units are placed on a solid flat surface near the installation location.
Refer to — Figure 2
1. Place the HF horn assembly (1) on top of the LF enclosure (2) with the three holes in
the pan-and-tilt bracket (not visible in the illustration), aligned with the three holes (3)
in the top of the LF enclosure.
2. Assemble the three bolts (4a), split washers (4b), and flat washers (4c) and install
through the pan-and-tilt bracket into the LF enclosure.
3. Tighten the bolts. Be careful not to over tighten.
Refer to — Figure 3
4. Connect the Neutrik SpeakON NL4 plug (1) (end of the wiring harness coming from the
HF System) to the LF Enclosure connector plate NL4 receptacle (2).
NOTE:The NL4 is a keyed plug/receptacle that can only go in one way.
5. After engaging the plug all the way, twist the plug clockwise until it locks.
6. Use the Mode switch (3) to select Bi Amp or Passive.
Passive Mode
– (— Figure 4) a single amplifier channel drives the entire system. The
Mode Switch (3) must be in the PASSIVE position and only the right-side pair of terminals
are used to connect the amplifier to the loudspeaker system.
Bi-Amp Mode
– (— Figure 5) two amplifier channels are required. One for the LF
enclosure and one for the Mid-Hi system.
CAUTION!
An active crossover must be used to protect the loudspeaker from
damage. It is highly recommended to use a QSC processor with factory DSP
presets for the SC-2150 for best results.
The Mode Switch must be in the BI-AMP position and all four terminals are used to connect the amplifier to the loudspeaker. The Low
Frequency amplifier connects to the left pair of terminals and the High Frequency amplifier connects to the right pair of terminals.
CAUTION!
In all cases, be sure to observe proper polarity when making connections. The “+” terminal of the amplifier
should connect to the “+” terminal of the loudspeaker.
In Bi-Amp mode, be sure that LF and HF connections are not reversed. HF drivers can be damaged if they are connected
to the low frequency amplifier.
— Figure 2 —
1
2
3
4
4a
4b
4c
DCS-2150-HF
DCS-2150-LF
— Figure 3 —
To Mid-High System
1
2
3
®
— Figure 4 —
To amplier channel
— Figure 5 —
To amplier channel two (HF)
To amplier channel one (LF)

Produktspezifikationen

Marke: QSC
Kategorie: Lautsprecher
Modell: SC-2150

Brauchst du Hilfe?

Wenn Sie Hilfe mit QSC SC-2150 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Lautsprecher QSC

QSC

QSC K8.2 Bedienungsanleitung

10 September 2024
QSC

QSC AD-P.SAT Bedienungsanleitung

9 September 2024
QSC

QSC KLA12 Bedienungsanleitung

9 September 2024
QSC

QSC K10 Bedienungsanleitung

21 August 2024
QSC

QSC AcousticPerformance AP-5122 Bedienungsanleitung

19 August 2024
QSC

QSC SC-1120 Bedienungsanleitung

16 August 2024
QSC

QSC AD-S282H Bedienungsanleitung

16 August 2024
QSC

QSC GP218-sw Bedienungsanleitung

16 August 2024
QSC

QSC SR-5152 Bedienungsanleitung

14 August 2024
QSC

QSC AD-P6T Bedienungsanleitung

14 August 2024

Bedienungsanleitung Lautsprecher

Neueste Bedienungsanleitung für -Kategorien-

Sonance

Sonance Visual Performance VP65 SST Bedienungsanleitung

16 Oktober 2024
Bowers And Wilkins

Bowers And Wilkins CWM664 Bedienungsanleitung

16 Oktober 2024
Focal

Focal Chorus 826 V Bedienungsanleitung

16 Oktober 2024
KEF

KEF Ci200ER Bedienungsanleitung

16 Oktober 2024
Steren

Steren SPK-1100BL Bedienungsanleitung

16 Oktober 2024
Aiwa

Aiwa SP-A100 Bedienungsanleitung

16 Oktober 2024
Trust

Trust GXT 628 Bedienungsanleitung

15 Oktober 2024
Pyle

Pyle PBMSPG6 Bedienungsanleitung

15 Oktober 2024
Marshall

Marshall Tufton Bedienungsanleitung

15 Oktober 2024
Sunstech

Sunstech SPUBT780 Bedienungsanleitung

15 Oktober 2024