QSC AD-S402T Bedienungsanleitung

QSC Lautsprecher AD-S402T

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für QSC AD-S402T (4 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/4
1TD-001597-01-A
AD-S402T
Quick Start Guide
NOTE:
The AD-S402T is UL listed (1480A) for indoor use only
Installation
AD-S402T passive column loudspeaker systems require amplified audio signals. A pass-through on each loudspeaker permits connection to multiple loudspeakers.
The pluggable “Eurostyle” connectors allow the installer to pre-wire the audio system on site before the loudspeakers are installed.
TD-001597-01-A
*TD-001597-01*
The loudspeaker comes with a weather cover for the input cup to protect the input connections and switches from
precipitation and other weather hazards (Figure 1). Use the weather cover for all non-UL outdoor installations or any
applications where the loudspeaker may be exposed to moisture. To ensure a good seal in the cable gland, use outdoor-rated
cable with a round jacket between 5.5 mm and 9.4 mm in diameter.
To use the weather cover:
1. Loosen the nut on the cable gland.
2. Pass the cable all the way through the nut and the rest of the gland.
3. Attach the input connector to the wires (see
Input Connector
, below).
4. Once the loudspeaker enclosure is installed, plug the input connector into the loudspeaker's input cup. Secure the
connector to the loudspeaker using the two captive retaining screws, one on each end.
5. Make sure that the transformer tap selection switch is set properly.
6. Place the cover onto the loudspeaker's input cup and attach it using the four screws, lock washers, and flat washers
provided.
7. Dress the cable so there is no undue strain on it. Tighten the gland nut until the grommet inside the gland has made a
tight seal onto the cable jacket.
Input Connector
AD-S402T Weather Cover
Diameter
up to
0.37 in
9.4 mm
— Figure 1 –
Strip wire
¼ in
6.3 mm
Up to
10 GAW
6 mm²
Turn screw fully
counterclockwise.
Insert wire fully.
Turn screw clockwise
to clamp wire tightly.
— Figure 2 –
INPUT
THRU To other
loudspeaker(s),
if necessary
— Figure 3 –
The pluggable “Eurostyle” input connector (Figure 2) has four terminals to facilitate connection on a distributed
line. It also allows the installer to pre-wire the venue before the loudspeakers themselves are installed. The
connector accommodates wire up to 10 AWG or 6 mm2. Be sure of proper and consistent polarity at each connector
(Figure 3). If one or more loudspeakers is out of polarity with others, the acoustic performance will suffer. Always
secure the connector to the loudspeaker using the retaining screws at both ends.
Mounting
Tilt/Swivel Bracket
The bracket provided with the loudspeaker allows 0, 5,
10, 15, and 20 degrees of downward tilt (Figure 4), and
up to ±55 degrees of horizontal panning (Figure 5).
These angles may be constrained by the loudspeaker
enclosure and adjacent walls or other structural elements.
In addition, the bracket can be inverted, which allows the
loudspeaker to be tilted up.
— Figure 4 –
— Figure 5 –
2
TD-001597-01-A
For mounting that requires no panning left or right, the bracket kit includes a zero-
pan locking screw to keep the loudspeaker securely in place.
The AD-S402T has three attachment locations for the bracket. Figure 6 shows their
center points, including distances from the bottom edge of the enclosure. Two M6 ×
20 screws with flat washers are included for attaching the bracket to the rear panel of
the enclosure. Inverting the bracket offers three more configurations to choose from
and allows the loudspeaker to be tilted up instead of down (Figure 7). In addition,
the loudspeaker enclosure itself can be inverted, which doubles the total number of
mounting possibilities—exclusive of tilt—to 12.
An M6 eyebolt is included with the loudspeaker for attaching a safety tether, as may
be required by building codes in your jurisdiction. Attach the eyebolt securely to the
end mounting hole or to one of the unused ones.
The table below describes the pan range for different bracket positions and tilt angles.
AD-S402T Maximum Pan Range
Bracket
Position 0° tilt 5° tilt 10° tilt 15° tilt 20° tilt
Tilt bracket
removed
1 ±55° ±55° ±55° ±54° ±54° N/A
2 ±55° ±54° ±53° ±51° ±49° ±50°
3 ±55° ±51° ±46° ±40° ±32° ±50°
4 (1 inverted) ±55° ±45° ±29° ±7° N/A N/A
5 (2 inverted) ±55° ±46° ±33° ±15° N/A N/A
6 (3 inverted) ±55° ±50° ±43° ±33° ±22° ±50°
Attaching the wall piece
Attach the wall piece to the wall or other mounting surface. Figure 8 is a full-size
template. Consult a structural engineer for guidance in selecting mounting locations
and appropriate fasteners.
73.0 mm
2.88 in
Position 1 or
4
92.9 mm
3.66 in
150.9 mm
5.94 in
Position 2 or
5
Position 3 or
6
Eyebolt
position
— Figure 6 – — Figure 7 —
3.35 in
85.0 mm
5.30 in
134.5 mm
0.33 in
8.4 mm
×2
1.57 in
40.0 mm
Use 8 mm
or 5/16 in
screws
— Figure 8 —
NOTE:
To use Figure 8 as a template, print
this page at (i.e., with no scaling).actual size
3TD-001597-01-A
Attaching the loudspeaker bracket pieces to allow tilting
1. Select the appropriate attachment location for the bracket on the enclosure
rear panel. Note that because of the wall or mounting surface, in most cases
the lowest attachment location offers the widest range of tilt options, while
the highest offers few, if any, tilt options.
2. Use two M6×20 screws and their washers to secure the bracket to the
enclosure. Note that the bracket has four mounting holes; some attachment
locations use the long-spaced holes and some use the shorter ones.
NOTE: For convenience reasons we recommend configuring the tilt angle
(Figure 9) before the loudspeaker and bracket are attached to the wall piece.
However, you can adjust the tilt later, even after the loudspeaker has been
installed.
3. Continue to Attaching the loudspeaker to the wall piece.
Attaching the loudspeaker bracket pieces for no-tilt
mounting
If the application does not require tilting the loudspeaker, you can either
configure it for 0 degrees or you can simplify the mounting bracket.
To simplify the mounting bracket, follow these steps
1. Omit these parts of the bracket kit, shown in Figure 10.
2. Attach this remaining part of the bracket directly to the loudspeaker enclosure
(see below left), using the two M6 × 20 screws (Figure 11).
3. Continue to Attaching the loudspeaker to the wall piece.
M5 × 42,
M4 × 9 shoulder screw
(2 places)
M4 flange nut
(2 places)
20°
15°
10°
5°
0°
Zero-pan
lock screw
M8 stud, washer,
and cap nut
(2 places)
— Figure 9 –
— Figure 10 –
M6 × 20
— Figure 11 –
Attaching the loudspeaker to the wall piece
1. The wall piece has a stud on the top and the loudspeaker bracket piece has a stud on the bottom.
Set the hole in the loudspeaker bracket piece over the wall piece's stud and guide the loudspeaker
bracket's stud through the hole in the wall piece (Figure 12).
2. Set the loudspeaker onto the wall piece.
3. Install a washer and cap nut on each stud and tighten them finger tight.
4. Adjust the horizontal pan of the loudspeaker as needed.
5. If the loudspeaker's desired horizontal angle is perpendicular to the wall, you may install the zero-
pan locking screw to keep it from moving out of position. Make sure that the threaded hole in the
loudspeaker bracket piece lines up with the hole in the wall piece, then insert and tighten the screw.
6. Tighten the cap nuts securely.
— Figure 12 –

Produktspezifikationen

Marke: QSC
Kategorie: Lautsprecher
Modell: AD-S402T

Brauchst du Hilfe?

Wenn Sie Hilfe mit QSC AD-S402T benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Lautsprecher QSC

QSC

QSC K8.2 Bedienungsanleitung

10 September 2024
QSC

QSC AD-P.SAT Bedienungsanleitung

9 September 2024
QSC

QSC KLA12 Bedienungsanleitung

9 September 2024
QSC

QSC K10 Bedienungsanleitung

21 August 2024
QSC

QSC AcousticPerformance AP-5122 Bedienungsanleitung

19 August 2024
QSC

QSC SC-1120 Bedienungsanleitung

16 August 2024
QSC

QSC AD-S282H Bedienungsanleitung

16 August 2024
QSC

QSC GP218-sw Bedienungsanleitung

16 August 2024
QSC

QSC SR-5152 Bedienungsanleitung

14 August 2024
QSC

QSC AD-P6T Bedienungsanleitung

14 August 2024

Bedienungsanleitung Lautsprecher

Neueste Bedienungsanleitung für -Kategorien-

Sonance

Sonance Visual Performance VP65 SST Bedienungsanleitung

16 Oktober 2024
Bowers And Wilkins

Bowers And Wilkins CWM664 Bedienungsanleitung

16 Oktober 2024
Focal

Focal Chorus 826 V Bedienungsanleitung

16 Oktober 2024
KEF

KEF Ci200ER Bedienungsanleitung

16 Oktober 2024
Steren

Steren SPK-1100BL Bedienungsanleitung

16 Oktober 2024
Aiwa

Aiwa SP-A100 Bedienungsanleitung

16 Oktober 2024
Trust

Trust GXT 628 Bedienungsanleitung

15 Oktober 2024
Pyle

Pyle PBMSPG6 Bedienungsanleitung

15 Oktober 2024
Marshall

Marshall Tufton Bedienungsanleitung

15 Oktober 2024
Sunstech

Sunstech SPUBT780 Bedienungsanleitung

15 Oktober 2024