Projecta SPP160K Bedienungsanleitung
Projecta
Solaranlage
SPP160K
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Projecta SPP160K (8 Seiten) in der Kategorie Solaranlage. Dieser Bedienungsanleitung war für 41 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/8
MONOCRYSTALLINE
12 VOLT
SOLAR PANEL KITS
P/No. SPP160K
2
WARNING
SOLAR PANEL
• For installations with lead acid batteries, avoid sparks or flames near the batteries and
always use proper eye protection
• Given sufficient light, solar panels always generate energy even when they are disconnected
• Accidental ‘shorting’ of the terminals or wiring can result in sparks causing personal injury or a
fire hazard
• Do not scratch or bend solar panels
• Do not disassemble the solar panel
• When mounting solar panels at a height adhere to all relevant safety regulations
• Do not walk on modules
• Do not attempt to increase module output by concentrating light on its surface with mirrors
• Be sure to use components (cables, fuses, etc) greater than 25% of solar panel’s maximum
current ratings
• When storing the Solar panel kit do not pack heavy items on top the Solar panel bag
• Do not disassemble the controller. Take to a qualified person if the unit requires repairing
FEATURE OVERVIEW
SOLAR PANEL
Compact and Powerful – Monocrystalline solar panels are manufactured from a solar cell that
is cast from silicon. These cells are more efficient at producing power than an amorphous panels,
so the size of the panel is smaller yet produces greater output power.
Heavy Duty Frame – Corrosion resistant frames are constructed to withstand wind speeds in
excess of 130 km/h in typical ground mounted applications. The frames are black anodized and
the corner connection has a strong mechanical resistance to weather.
Convenient Carry Bag – This durable padded bag protects your solar panel during storage
and transportation.
Carry Handle & Safety Latches – It is easy to carry the solar panels whilst out of the bag with
the carry handle and using the safety latches to keep the solar panels closed shut.
5 Meter Lead with Battery Clamps – 5 meter battery leads are connected to the solar panels
with battery clamps, so all you have to do is connect to the battery.
Fold Away Support Legs – The convenient support legs fold out from the rear to allow
easy mounting on flat ground. The legs place the panels at an optimum angle for maximum
performance.
3
P/No. SPP160K
TYPE MONOCRYSTALLINE
RATED POWER 160W
OPEN CIRCUIT VOLTAGE 22.6V
SHORT CIRCUIT CURRENT 10.2A
PEAK POWER VOLTAGE 17.0V
PEAK POWER CURRENT 9.42A
TEST CONDITIONS 1000W/m2, 25˚C
BATTERY CONNECTIONS Battery Clamps
SPECIFICATIONS
SOLAR CONTROLLER
Advanced MCU – Features control pulse width modulated (PWM) technology, high efficiency
operation.
Multi-Chemistry – Target for Gel, AGM, Conventional lead-acid (WET) and Calcium Batteries.
5 Stage solar controller – Built in regulator to prevent your battery from being overcharged.
Overcharging occurs when the charge voltage is unregulated. This can result in premature
battery failure.
The regulator also prevents your battery from being under charged, in the solar energy field,
battery undercharge always occurs, especially on some Conventional lead – acid or Calcium
batteries; The unit provides an automatic Equalization feature for deeply drained Conventional
lead acid batteries or Calcium batteries.
It keeps the battery fully charged by using a process called “floating”. This means the controller
will stop charging when the battery is full and will automatically start charging the battery as
required. This process will also reduce water loss and help prevent the battery from ‘drying out’.
Multi-Chemistry – Suitable for charging Gel, AGM (Sealed), Conventional lead-acid (WET) and
Calcium batteries.
Discharge Protection – Protects your battery from discharge at night. Under low light or no
light conditions the solar panel voltage could be less than the battery voltage. The unit contains
a special circuit which prevents current flowing back from the battery and into the solar panel.
LED Indicators – Coloured LED’s to easily indicate the operational status and battery conditions.
Unit Protection – Protects against reverse polarity, short circuit, over temperature, over voltage, etc.
BATTERY TYPE SELECTION
Please check your battery manufacturer’s specifications to select correct battery type.
The unit provides 4 battery types for selections: Gel, AGM, WET (conventional lead acid),
and Calcium.
There is a DIP switch at the back of the solar charge controller, this Dip switch is used for
presetting your battery type. Please refer to Figure 1.1 to make DIP switch setting for the
proper battery chemical; the factory default setting is at AGM battery type.
Produktspezifikationen
| Marke: | Projecta |
| Kategorie: | Solaranlage |
| Modell: | SPP160K |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Projecta SPP160K benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Solaranlage Projecta
20 Januar 2024
9 Januar 2024
12 Dezember 2023
20 September 2023
11 Oktober 2022
Bedienungsanleitung Solaranlage
- Solaranlage BenQ
- Solaranlage LG
- Solaranlage Velleman
- Solaranlage Technaxx
- Solaranlage Mestic
- Solaranlage KKT Kolbe
- Solaranlage Polaroid
- Solaranlage Tesla
- Solaranlage Perel
- Solaranlage Biltema
- Solaranlage Paulmann
- Solaranlage EasyMaxx
- Solaranlage Furrion
- Solaranlage Dörr
- Solaranlage Steren
- Solaranlage Growatt
- Solaranlage SolarEdge
- Solaranlage EcoFlow
- Solaranlage BlauHoff
- Solaranlage Tycon Systems
- Solaranlage FOX ESS
- Solaranlage NuaSol
- Solaranlage Sunware
- Solaranlage BLUEPALM
- Solaranlage Yingli Solar
Neueste Bedienungsanleitung für -Kategorien-
12 August 2024
25 Juni 2024
25 Juni 2024
10 Juni 2024
6 Juni 2024
6 Juni 2024
6 Juni 2024
1 Juni 2024
1 Juni 2024
30 Mai 2024