Proficient Ceiling C1030 Bedienungsanleitung

Proficient Lautsprecher Ceiling C1030

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Proficient Ceiling C1030 (4 Seiten) in der Kategorie Lautsprecher. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/4
C1030
LCR Ceiling Speaker
Audio Systems
OWNER’S MANUAL
Thank you for purchasing the C1030 LCR Ceiling Speaker. The
directional woofer and pivoting midrange and tweeter make
the C1030 a perfect choice for in-ceiling home cinema speaker
setups, from stereo and LCR (left-center-right), to 3.1, 5.1 and
7.1 configurations. The three-way speaker system with 10"
woofer brings you an extraordinarily robust music or cinema
experience, while the ±3dB midrange and tweeter adjustments
provide ultimate fine-tuning to room size and acoustics, or
according to personal preference.
• (1) C1030 LCR Ceiling Speaker & Grille
• (1) PCB-C1000 Mounting Bracket
• (1) Hole-Cutting Template
• (1) Paint Mask Insert
WARNING: To avoid possible injury, the PCB-C1000
Mounting Bracket must be used with the C1030
speaker for both new construction and retrofit
installations. The included mounting bracket
was specifically designed to support the weight and size of the
C1030, and to prevent it from coming loose and dropping from
the ceiling. Always use the PCB-C1000 Mounting Bracket when
installing the C1030 speaker.
INTRODUCTION PACKAGE CONTENTS
Before installing your C1030 LCR Ceiling Speaker, you should
consider its placement carefully, taking into account the
location of HVAC ducts, electrical conduit, plumbing lines,
and other fixtures. For retrofit installations, this can best be
determined by noting the placement of fixtures and gaining
access to an attic or crawl space for further analysis of the
location of such obstacles.
Prior to the actual installation of the speaker, it will be
necessary to run wiring to the speaker location. After the
wire has been properly installed, you are ready to install the
mounting bracket. For new construction, mount the speaker
after the drywall installation is complete.
Placement in Ceiling: When placing your speaker into the
ceiling, it should be located so that the fixed 15˚ angle woofer
is pointed toward the primary listening area. If the speaker is
positioned away from the primary listening area, simply adjust
the pivoting midrange and tweeter so they are pointed toward it.
Note: To avoid possible damage to the pivoting midrange and
tweeter, read the section entitled “SPEAKER ADJUSTMENTS”
in this manual prior to performing the adjustment. In very
large rooms with low ceilings, it may be necessary to place
additional speakers throughout the room for better coverage.
SPEAKER PLACEMENT & SETUP
The included PCB-C1000 Mounting Bracket is designed for both
new construction & retrofit installations. The PCB-C1000 Mounting
Bracket may be installed prior to drywall application across joists
(from 16" to 24" on-center) where a speaker will be located.
For new construction, the PCB-C1000 Mounting Bracket is also
available separately, in the event that the C1030 speaker has not
yet arrived on-site, or is otherwise not available. Always use the
PCB-C1000 Mounting Bracket when installing the C1030 speaker.
To install the mounting bracket in new construction:
1. Find the joists nearest the desired speaker mounting
location. If you need to align the speaker to some other object
or molding in the room, be sure to consider the size of the
baffle flange which extends beyond the mounting hole.
2. Line up bottom of one of the mounting bars with the
bottom of the joist. This will place the screw holes in an “L”
position, flush with the side of the joist, and the mounting ring
“lip” will be facing downward. Attach the mounting bar to the
joist using appropriate wood screws.
3. Make sure that the mounting ring is in a perfectly circular
shape by opening the bracket until the arms come in contact
with the stoppers. Then, line up the bottom of the other
mounting bar with the bottom of the same joist. Attach the
mounting bar to the joist using appropriate wood screws.
MOUNTING BRACKET INSTALLATION – NEW CONSTRUCTION (See Diagram 1)
2
The included PCB-C1000 Mounting Bracket is designed for
both new construction and retrofit installations. The intelligent
folding design facilitates mounting the bracket through a
speaker cut-out, therefore the mounting bracket may be
installed across 16" to 24" on-center joists after drywall is
installed. Always use the PCB-C1000 Mounting Bracket when
installing the C1030 speaker.
Retrofit Installation - Finished Ceilings
Follow the first set of instructions to prepare the mounting
surface for a professional looking installation. Then, follow the
second set of instructions for the mounting bracket installation.
To prepare the mounting surface in a retrofit installation:
1. Find the joists nearest the desired speaker mounting
location. We highly recommend using a good stud-finder tool
for this procedure. If you need to align the speakers to some
other object or molding in the room, be sure to consider the
size of the baffle flange which extends beyond the mounting
hole. Please allow 1¼" space from the joist.
2. Mark the hole. A template for setting the hole is provided in
the box (along with a paint mask insert for use when painting).
Position the template in the desired position and pencil an
outline on the ceiling.
3. Cut the hole. CAUTION: This is the most important part
of the entire installation. If you are not certain whether any
obstructions exist behind the desired mounting area, you
should start by cutting a small hole in the center of your
penciled mounting hole with a drywall saw, cutting at a 45°
angle towards the inside of the hole. (See Diagram 3) Cutting
the small hole at this angle will make drywall repair much
easier, using the piece cut out. Once you have determined that
there aren’t any obstructions in your desired mounting location,
cut the finished hole at a 90° angle to the ceiling surface.
To install the mounting bracket in a retrofit:
1. Move the mounting bars in opposite directions, so that the
mounting ring folds down to its narrowest width. Collapse the
mounting bars to their shortest length.
2. With the mounting ring lip facing downward, insert
the mounting bracket into the ceiling cavity through the
previously cut hole in the ceiling drywall.
3. Make sure that the mounting ring is in a perfectly circular
shape by opening the bracket until the arms come in contact
with the stoppers, then set it into the ceiling hole. Push one
of the mounting bar L-shaped edges until it is flush with the
joist, and the bottom of the mounting bar lines up with the
bottom of the joist. Attach the mounting bar to the joist using
appropriate wood screws.
4. Push the other mounting bar L-shaped edge until it is flush
with the same joist, and the bottom of the mounting bar lines
up with the bottom of the joist. Attach the mounting bar to
the joist using appropriate wood screws.
5. Stretch both mounting bars to reach the opposite joist, then
line up the bottoms of each mounting bar with the bottom
of the joist. Attach each mounting bar to the joist using
appropriate wood screws.
6. If the area in the ceiling is not already insulated, add an
adequate amount of insulation material to loosely cover where
the speaker will be positioned, being sure that the speaker wire
remains accessible. If the insulation material used is faced with
foil or paper, position the foil or paper away from the speaker.
4. Stretch both mounting bars to reach the opposite joist, then
line up the bottoms of each mounting bar with the bottom
of the joist. Attach each mounting bar to the joist using
appropriate wood screws.
5. To adjust the position of the mounting ring between the
joists, grab both sides of the mounting ring, where it connects
to the mounting bar, then move the mounting ring into the
desired position.
6. If the area in the ceiling is not already insulated, add an
adequate amount of insulation material to loosely cover where
the speaker will be positioned, being sure that the speaker wire
remains accessible. If the insulation material used is faced with
foil or paper, position the foil or paper away from the speaker.
Adding insulation may also be done after drywall installation.
The protruding lip of the mounting ring will force the drywall
installers to hang the drywall with an appropriate hole cut out
around the mounting ring lip. After the drywall has been hung
and finished, the speakers are then easily installed following the
instructions for mounting in “SPEAKER INSTALLATION” below.
MOUNTING BRACKET INSTALLATION – RETROFIT (See Diagrams 1, 2 & 3)
Diagram 3
Diagram 2
PCB-C1000 Closed Position
Mounting Ring Lip
Screw Holes
Mounting Ring
Mounting Bar
Diagram 1
PCB-C1000 Open Position
3
The unique integral mounting system incorporated into each
LCR Ceiling Series speaker allows for a quick installation by
following these easy steps:
1. Attach the speaker wire, observing the proper polarity with
your amplifier, + to + and – to –. Make sure the appropriate
channel of the amplifier is connected to the correct speaker
(i.e. left, right or surrounds).
2. Be sure the mounting feet are turned inward to clear the
opening, and insert the speaker into the ceiling. Position the
speaker into the hole, being sure that the angled baffle is
pointed toward the intended direction.
Note: The flange of the speaker is designed to flex and
conform to any small imperfections in the ceiling’s surface.
Tighten the screws on the front of the baffle only enough to
make the flange become snug against the ceiling.
3. As you tighten the screws, the feet automatically flip into an
outward position (See Diagram 4), and begin to tighten from
the backside, thereby clamping the drywall and mounting ring
between the feet and the flange.
CAUTION: Overtightening may warp the baffle, crack the
ceiling, cause the flange to distort, and make the grille difficult
to install.
4. Push the grille firmly into the slot around the speaker baffle.
The LCR Ceiling Series speakers come from the factory with the
midrange and tweeter in line with the 15˚ angle of the woofer.
This will result in the optimal directivity of the speaker system.
However, depending on your particular primary listening area,
room acoustics, ceiling height, or personal preference, you may
find the sound more pleasing by pointing the midrange and/or
tweeter in a particular direction.
For example, if additional treble
is desired in the primary listening
area, point the tweeter toward
that area; and if less treble is
required, point the tweeter away.
Push gently at the edge of the
tweeter to point it in the desired
direction. For optimal directivity
of the midrange, point it towards
the listening area. If you wish to
diffuse the midrange, such as
when using a C1030 as a side-fill
in a 7.1 setup, point the midrange
speaker slightly away from the
listening area.
CAUTION: Avoid touching metal dome tweeters or midrange
speaker surfaces, as damage may occur. Carefully press on the
edge of each pivoting mechanism as indicated. (See Diagram 5)
Tweeter Adjustment:
The switch labeled TREBLE allows
for ±3dB of treble adjustment.
Your speakers are shipped with
the treble switch in the middle
position, providing the most linear
frequency response. If you desire
more treble, move the switch to
the “+” position, and the tweeter
will play 3dB louder. If you desire
less treble, move the switch to the
“–” position, and the tweeter will
play 3dB softer. To return to the
neutral setting, move the switch
back to the middle position. (See Diagram 6)
Midrange Adjustment:
The switch labeled MIDRANGE allows for ±3dB of midrange
adjustment. Your speakers were shipped with the midrange
switch set to the middle position, providing the most linear
frequency response. If you desire more midrange, move the
switch to the “+” position and the midrange will play 3dB
louder. If you desire less midrange, push the switch to the “–”
position and the midrange will play 3dB softer. To return to the
neutral setting, move the switch back to the middle position.
(See Diagram 6)
If you plan to paint your speaker (grille and flange), we
recommend that it be done prior to installation. If you plan to
paint your speaker sometime in the future, it is best to remove
it by simply reversing the steps for “SPEAKER INSTALLATION”
above. If it is necessary to paint the speaker while it's still in
the ceiling, the paint mask provided in the carton must be
installed in place of the grille while the flange is being painted
with the ceiling.
Do not paint the grille while it's installed on the speaker.
Before painting, remove the material from the inside of the
grille. Once the grille has been painted, return the material
back into place. Great care should be taken not to clog the
holes of the grille, as this will reduce both the sonic and
aesthetic qualities of the speakers. Proficient recommends
only light spray painting using 5 parts thinning agent to 1
part paint.
Mounting Feet
Flange
SPEAKER INSTALLATION
SPEAKER ADJUSTMENTS
PAINTING THE SPEAKER
Diagram 4
Diagram 6
Push Tweeter Here
Push Midrange Here
Diagram 5

Produktspezifikationen

Marke: Proficient
Kategorie: Lautsprecher
Modell: Ceiling C1030

Brauchst du Hilfe?

Wenn Sie Hilfe mit Proficient Ceiling C1030 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Lautsprecher Proficient

Proficient

Proficient C850 Bedienungsanleitung

31 August 2024
Proficient

Proficient Ceiling C500 Bedienungsanleitung

31 August 2024
Proficient

Proficient W800 Bedienungsanleitung

31 August 2024
Proficient

Proficient Protege C646 Bedienungsanleitung

31 August 2024
Proficient

Proficient GL6 Bedienungsanleitung

31 August 2024
Proficient

Proficient C660 Bedienungsanleitung

31 August 2024
Proficient

Proficient C605 Bedienungsanleitung

31 August 2024
Proficient

Proficient Ceiling C640 Bedienungsanleitung

31 August 2024
Proficient

Proficient W670 Bedienungsanleitung

31 August 2024
Proficient

Proficient C645 Bedienungsanleitung

31 August 2024

Bedienungsanleitung Lautsprecher

Neueste Bedienungsanleitung für -Kategorien-

Sonance

Sonance Visual Performance VP65 SST Bedienungsanleitung

16 Oktober 2024
Bowers And Wilkins

Bowers And Wilkins CWM664 Bedienungsanleitung

16 Oktober 2024
Focal

Focal Chorus 826 V Bedienungsanleitung

16 Oktober 2024
KEF

KEF Ci200ER Bedienungsanleitung

16 Oktober 2024
Steren

Steren SPK-1100BL Bedienungsanleitung

16 Oktober 2024
Aiwa

Aiwa SP-A100 Bedienungsanleitung

16 Oktober 2024
Trust

Trust GXT 628 Bedienungsanleitung

15 Oktober 2024
Pyle

Pyle PBMSPG6 Bedienungsanleitung

15 Oktober 2024
Marshall

Marshall Tufton Bedienungsanleitung

15 Oktober 2024
Sunstech

Sunstech SPUBT780 Bedienungsanleitung

15 Oktober 2024