Primera LX810e Bedienungsanleitung

Primera Etikettendrucker LX810e

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Primera LX810e (2 Seiten) in der Kategorie Etikettendrucker. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

6Install Cartridges

Quick Start

P/N 510929-060409

7Finishing the Install 8Congratulations

Once you have installed the media, the installer

will prompt you to install the cartridges.

Open the Top Cover. Click the Install Cartridges

button to start the cartridge installation process.

The Cartridge Carrier will move itself to the center

of the print area.

1. Press the Cartridge Cover Release to open the

Cartridge Holder.

2. Remove each cartridge from its packaging

and slowly remove the tape covering the

cartridge's print head.

3. Replace/install the cartridge.

4. Push cartridge cover downward until it snaps

in place.

5. Close the Top Cover.

Click Finished Installing Cartridges to confirm

the cartridges have been installed. You will now

be prompted to align your cartridges.

Click Align Cartridges to start the cartridge

alignment. The Printer will now print and

automatically scan a pattern of lines that will

align the black cartridge to the color cartridge.

12 3

After the cartridges and the label media have

been installed and configured, the installer will

complete its process by installing the NiceLabel

SE software on your computer. Simply click

Next to continue installing, and follow the

onscreen instructions to the finish.

Note: For optimal printing speed you MUST

reboot the PC after installing the software!

Congratulations! Your LX810e Color Label

Printer is now installed and ready for use.

Please refer to Section 3 of the User Manual

for a tutorial on using NiceLabel®SE.

*after registering your

product. See

www.primerawarranty.com

for terms and conditions.

Unpack Your Printer

•Printer

•Separate Power Cord

•Power Adapter

•Software Installer CD

•Color Ink Cartridge

•Dye-Based Black Ink Cartridge

•Starter roll of label stock 6" x 4" High-Gloss

(Located inside the Printer in a cardboard

shipping insert)

•Tear Bar Guard

•This manual and other printed information

Important!

Before continuing open the printer cover. Remove

the cardboard insert holding the print carriage in

place and the cardboard insert around the roll arm.

Note

For optimal printing speed you must have

a PC with the following minimum

specifications:

•Pentium IV Processor

•512 MB of RAM

•5 GB of Free Hard Drive Space

5Install Label Material

2Quick Start Installer (PC)

The installer should prompt you to install label

material. It is recommended for the first install

that you use the starter label roll that ships with

your printer.

1. Open the Top Cover.

2. Lower the Roll Guide and pull it outward to

make room for your label stock.

3. Pull the Movable Throat Guide outward to

make room for the label stock.

4. Remove any shipping tape from your label

stock roll to ensure that it can unroll freely,

making certain that no adhesive portion is

exposed. It is important to note that any

exposed adhesive surface can attach itself the

the inner workings of the print mechanism

and cause a media jam.

5. Place your roll of label stock on the Roll Arm

and push it inward until it touches the stop.

6. Flip up the Roll Guide and slide it inward

until it touches the label stock. (The Roll

Guide will automatically pull back slightly

to the correct position)

7. Place the leading edge of label

stock under the "label stock"

symbols on the Throat Guides. The label

stock should be placed far enough into the

throat of the printer to correctly position the

Movable Throat Guide but not yet into the

printer itself. The label stock should be

biased against the Fixed Throat Guide.

8. Slide the Movable Throat Guide inward until

it almost touches the label stock. There must

be slightly more space between the Throat

Guides than the width of the label stock.

If the label stock is pinched by the guides,

poor print quality or even feeding problems

could result.

9. Feed the label stock further into the printer

until it senses the label and automatically

feeds it through the printer.

Roll Arm

Movable Throat Guide

Sensor Position Adjust

Roll Guide

Fixed Throat Guide

2. Lower the Roll Guide

and Pull it Outward.

1. Open Cover.

3. Pull Throat Guide Out.

5. Place label stock

on Roll Arm.

6. Slide Roll Guide

assembly inward.

8. Slide Throat

Guide inward,

until it almost

touches the

label stock.

1. Insert the Installation CD into your

computer. In a few moments the installer

program should

launch automatically.

If not, perform the

following steps:

a. Double click My

Computer Icon,

then double click

the icon of the

appropriate CD drive containing the

software installer disc.

b. Double click INSTALL.exe then click

the Quick Start Install Button.

Apply Power

Turn on the Power Switch.

Power Switch

Plug in the USB Cable

After a few moments Windows will detect

the printer and attempt to install the printer

driver. Follow the on-screen prompts to

install the driver. You will be prompted with

a dialog box like the one shown here:

Click "Continue Anyway".

Once installed the "Color Label Printer" icon

will appear in the printers folder.

Connecting the USB Cable

9. Feed the label stock further

into the printer until it senses the

label and automatically feeds it

through the printer.

7. Place the leading edge of

the label stock just past the

Throat Guides.

Label Stock

2Quick Start Installer (continued)

2. In the installer application click the Quick

Start Install Button. The QuickStart Install

will guide you step-by-step through the

installation process. As you complete each

step, click Next. Steps 3-7 are shown below

as well as on the monitor. You may follow

either to complete the setup.

For Macintosh instructions refer to

section 1G of the Users Manual.

Produktspezifikationen

Marke:	Primera
Kategorie:	Etikettendrucker
Modell:	LX810e
USB Anschluss:	Ja
WLAN:	Nein
Breite:	432 mm
Tiefe:	394 mm
Gewicht:	13200 g
Produktfarbe:	Weiß
Übertragungstechnik:	Kabelgebunden
Höhe:	231 mm
Anzahl USB 2.0 Anschlüsse:	1
Zertifizierung:	UL, UL-C, CE, FCC
Netzteil Ausgangsspannung:	12 V
AC-Adapter Ausgangssstrom:	0.5 A
Farbe:	Ja
LED-Anzeigen:	Ja
Mac-Kompatibilität:	Ja
Energiebedarf:	100 - 240V, 50/60Hz
Min. benötigter RAM:	512 MB
Kompatible Betriebssysteme:	Windows XP\nWindows Vista\nWindows 7\nMac OS X v10.2+
Abmessungen (BxTxH):	432 x 394 x 231 mm
Maximale Auflösung:	4800 x 1200 DPI
Mitgelieferte Software:	NiceLabel SE
Standard-Schnittstellen:	USB
Druckgeschwindigkeit (metrisch):	51 mm/sek
Maximaler Rollendurchmesser:	152 mm
Druckfarben:	Cyan, Magenta, Yellow
Maximum Druckweite:	210 mm
Minimum Prozessor:	Intel Pentium IV, G4
Min. benötigter Speicherplattenplatz:	5000 MB
Kerndurchmesser:	76 mm
Maximale Etikettenlänge:	0.609 m
Ethernet/LAN:	Nein