Praktica Luxmedia Z250 Bedienungsanleitung

Praktica Kamera Luxmedia Z250

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Praktica Luxmedia Z250 (86 Seiten) in der Kategorie Kamera. Dieser Bedienungsanleitung war für 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/86
1
Preface
About this Manual
• The contents of this manual and the bundled Basic Reference are subject to
change without notice.
• Note that the example screens and product illustrations shown in this User’s
Guide may differ somewhat from the screens and configuration of the actual
camera.
Copyright
This manual contains proprietary information protected by copyright. All rights
are reserved. No part of this manual may be reproduced by any mechanical,
electronic or other means, in any form, without prior written permission of the
manufacturer.
© Copyright 2015
Declaration of Conformity
This device complies with Part 15 of the FCC rules. Operation is subject to the
following conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference
that may cause undesired operation.
CE Mark Warning
This is a Class B product, in a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
FCC: SAR standard Value: 1.6 W/Kg, Maximal Measure: 0.27 W/Kg
CE: SAR standard Value: 2.0 W/Kg, Maximal Measure: 0. W/Kg 077
Trademark Recognition
Windows XP/Vista/Win7/Win 8 are registered trademarks of Microsoft
Corporation in the United States and/or other countries. Windows is an
abbreviated term referring to the Microsoft Windows Operation System. All
other companies or product names are trademarks or registered trademarks of
their respective companies.
2
Federal Communication Commission Interference Statement
APPLIES TO USA AND CANADA ONLY
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
ï‚·
Reorient or relocate the receiving antenna.
ï‚·
Increase the separation between the equipment and receiver.
ï‚·
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
ï‚·
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
This device is intended only for OEM integrators under the
following conditions:
1)
The antenna must be installed such that 20 cm is maintained between the
antenna and users, and
2)
The transmitter module may not be co-located with any other transmitter or
antenna.
As long as 2 conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
3
end-product for any additional compliance requirements required with this
module installed .
IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or co-location with another transmitter),
then the FCC authorization is no longer considered valid and the FCC ID can not
be used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna
may be installed such that 20 cm may be maintained between the antenna and
users. The final end product must be labeled in a visible area with the following:
"Contains FCC ID: 2AAD3AA0D0". The grantee's FCC ID can be used only when
all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warnings
as shown in this manual.
Industry Canada statement
This device complies with RSS- of the Industry Canada Rules. Operation is 210
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operatio n.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable
aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux
conditions suivantes: (1) le dispositif ne doit pas produire de brouillage
préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un
brouillage susceptible de provoquer un fonctionnement indésirable.
This device is intended only for OEM integrators under the
following conditions: (For module device use)
1)
The antenna must be installed such that 20 cm is maintained between the
antenna and users, and
2)
The transmitter module may not be co-located with any other transmitter or
antenna.
As long as 2 conditions above are met, further transmitter tests will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed.

Produktspezifikationen

Marke: Praktica
Kategorie: Kamera
Modell: Luxmedia Z250

Brauchst du Hilfe?

Wenn Sie Hilfe mit Praktica Luxmedia Z250 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Kamera Praktica

Praktica

Praktica Luxmedia WP240 Bedienungsanleitung

20 August 2024
Praktica

Praktica Luxmedia Z250 Bedienungsanleitung

18 August 2024
Praktica

Praktica Luxmedia Z212 Bedienungsanleitung

16 März 2024

Bedienungsanleitung Kamera

Neueste Bedienungsanleitung für -Kategorien-

Trust

Trust Powerc@m 820 Bedienungsanleitung

15 Oktober 2024
Bushnell

Bushnell Trophy Cam 119456 Bedienungsanleitung

13 Oktober 2024
Polaroid

Polaroid 600 Series Bedienungsanleitung

9 Oktober 2024
Fujifilm

Fujifilm FinePix F500EXR Bedienungsanleitung

7 Oktober 2024
Rollei

Rollei Giro 105 Bedienungsanleitung

6 Oktober 2024
Leica

Leica R3 Bedienungsanleitung

5 Oktober 2024
Rollei

Rollei Compactline 52 Bedienungsanleitung

5 Oktober 2024
Kodak

Kodak EasyShare C1530 Bedienungsanleitung

4 Oktober 2024
Easypix

Easypix V515 Duo Bedienungsanleitung

3 Oktober 2024
Canon

Canon EOS R10 Bedienungsanleitung

3 Oktober 2024