PowerWalker VI 800 CSW Bedienungsanleitung

PowerWalker Unterbrechungsfreies Stromversorgungssystem VI 800 CSW

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für PowerWalker VI 800 CSW (4 Seiten) in der Kategorie Unterbrechungsfreies Stromversorgungssystem. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

ENGLISH

PowerWalker VI 600 1500 CSW-

Quick Guide

I. Overview:

1. LCD display

2. Up/down buon

3. Mute buon

4. ON / OFF buon

5. USB charging port

(5V / 2.1A shared

between 2 ports)

6. USB Communicaon

port with HID support

7. Surge protected -

outlets (no baery

backup)

8. Baery backup with

surge protected

outlets

9. RJ-45 surge protecon

(i.e. for Internet)

10. AC input

11. Venlaon and fan.

12. Circuit breaker (for

French and Schuko)

Surge protected outlets offer EMI ltering, line condioning and surge protecon, -

but they are not supported with backup power from battery in case of AC failure.

II. Operaon

Buon

Funcon

ON/OFF

buon

Press and hold the On/O Buon for 2 seconds and then release to

change state between Standby (output is o) and Line (output is on).

Mute buon

Press and hold the Mute buon for 1 second and then release to

mute or unmute the alarm.

Up/down

buon

Click to switch displayed informaon.

ENGLISH

III. Display

State

Display

Meaning

LED

Alarm

Line /

Standby /

Baery

mode

Input voltage, input frequency, baery voltage, baery

Power, Backup me, output voltage, output frequency,

load Power and load percentage.

k: kilo, W: wa, V: voltage, A: ampere, %: percent, degC:

centigrade degree, Hz: frequency, min: minute

Line

Mode

The UPS is connected to AC input.

AVR

Mode

ashing

When the icon is ashing, the UPS is regulang the

voltage (reducing or increasing the voltage).

Baery

Mode

The UPS is running on battery

every

10 s

All Modes

The UPS alarm is disabled.

All Modes

Baery level in ranges 0 24%, 25 49%, 50 74%, and 75- - - -

100%.

Baery

Mode

Low Battery

every

0.5s

every

All Modes

Load level in ranges 0-24%, 25-49%, 50-74% and 75-100%.

All Modes

Indicates overload.

every

0.5s

every

0.5s

All Modes

Baery replacement needed or the baery is not

connected

Conn

uous

every

Fault

Fault code (here: E14). Check troubleshoong for details.

Connu

ous

Warning

Baery voltage is too high (i.e. wrong baery inserted)

every

1.5s

ENGLISH

IV. Baery Replacement

1. Turn o the connected equipment and unplug it

from the UPS

2. Turn o the UPS and unplug the input cable.

3. Remove two screws located on the boom of the

UPS and slide the baery cover downward, then

outward.

4. Disconnect the baery connector.

5. Slide out the exisng baery pack from the UPS

by grasping the baery pull tap.

Cauon - Do not short the posive wire and negave wire

of baery.

Cauon - DO NOT pull the baery pack out by pulling on

the baery wires.

6. Slide the new baery pack into the UPS.

7. Verify proper polarity. Re connect the baery -

connectors together.

8. Reinstall the battery cover onto the UPS. Now,

the UPS is ready for normal operaon

9. Properly dispose of the old baeries at an

appropriate recycling facility or return them to

the supplier in the packing material for the new

baeries.

Please read all of the WARNINGS and CAUTIONS in the General Manual before

replacing the baeries.

V. Troubleshoong

Fault

Event

E12

Baery mode output high (internal fault)

E14

Output short (check the loads)

E15

Output over current (too much load)

E20

Fan lock fault

E21

Over Charge Voltage (i.e. wrong baery used)

E28

Low baery voltage

E43

Overload fault

Please check hps://troubleshoot.powerwalker.com for more details.

Produktspezifikationen

Marke:	PowerWalker
Kategorie:	Unterbrechungsfreies Stromversorgungssystem
Modell:	VI 800 CSW
Display-Typ:	LCD
USB Anschluss:	Ja
Gewicht:	8400 g
Mitgelieferte Kabel:	USB-Kabel
Produktfarbe:	Schwarz
Akkuladezeit:	8 h
Energieschutzeigenschaften:	Overcharge, Overload
Stecker:	C14-Koppler
Anzahl USB 2.0 Anschlüsse:	2
Betriebstemperatur:	0 - 40 °C
Relative Luftfeuchtigkeit in Betrieb:	0 - 90 %
Verpackungsbreite:	188 mm
Verpackungstiefe:	378 mm
Verpackungshöhe:	387 mm
Paketgewicht:	8300 g
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	2
Betriebsanleitung:	Ja
Reaktionszeit:	6 ms
LED-Anzeigen:	Ja
Geräuschpegel:	40 dB
Anzahl unterstützter Akkus/Batterien:	1
Akku-/Batteriespannung:	12 V
Batteriekapazität:	9 Ah
Formfaktor:	Tower
Ausgangsleistung:	480 W
Produkte pro Palette:	75 Stück(e)
Eingangsfrequenz:	50/60 Hz
Leistungsfaktor:	0.6
Anzahl der AC-Ausgänge:	8 AC-Ausgänge
USV-Topologie:	Line-Interaktiv
Eingangs-Betriebsspannung (min):	170 V
Eingangs-Betriebsspannung (max):	280 V
Ausgangskapazität:	0.8 kVA
Ausgangs-Betriebsspannung (min):	- V
Ausgangs-Betriebsspannung (max):	230 V
Automatische Spannungsregulierung:	Ja
AC-Steckertypen:	C13-Koppler
Typische Backup-Zeit bei halber Belastung:	10 min
Typische Backup-Zeit bei voller Belastung:	3 min
Wellenform:	Reiner Sinus
Regulierung der Ausgangsspannung:	10 %
USB-Port-Typ:	USB Typ-A