Power Craft EOS 170 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Power Craft EOS 170 (8 Seiten) in der Kategorie Sander. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
GB
Art.-Nr.: 44.604.05
Operating Instructions
Orbital sander
EOS 170
Anleitung EOS 170 02.11.2001 10:24 Uhr Seite 1
2
Please read these operating instruc-
tions carefully with particular atten-
tion to the safety notes. Always
store these operating instructions
together with the orbital sander.
Technical data
Voltage 230 Volts
Power consumption 135 Watts
Grinding surface area 180 x 85 mm
Sandpaper size 225 x 85 mm
Vibrations per minute 20,000
Shockproof, interference suppressed
Designed in accordance with appli-
cable VDE standards
Included in delivery
EOS 170, orbital sander
Dust extraction connectors ø 32, ø 36,
Operating instructions,
3 sheets of sandpaper
General safety notes
– Always remove the plug from the
power supply socket before carrying
out any maintenance or repair work
such as cleaning the sander or
changing the sandpaper!
– Always disconnect the machine by
removing the plug from the socket,
not by pulling on the mains cable.
– Always wear safety goggles and
dust mask when working.
– Keep the workplace clean and well
illuminated.
– Ensure that the workpiece is suffi-
ciently secured so that you are able
to work safety and effectively.
– Keep children away from the
machine.
– Always keep your machine clean,
and check for possible defects of
damage after every job.
– Always ensure that the switch is
switched off before you insert the
plug into the power supply socket.
– Ensure that any platforms you are
working on are sturdy and stable.
– If the machine is damaged, use the
exploded diagram and the spare
parts list to order any neccessary
parts from Customer Service.
1 Front grip
2 Machine identification
plate
3 On/Off trigger
4 Locking button
5 Main grip
6 Sandpaper
7 Vibration plate
8 Clamping device
9 Vacuum cleaner
attachment
10 Electrical cord
Attaching the dust extraction
connector
Note!
For health reasons, you must use a dust
extraction device.
Warning!
– The orbital sander is not
designed for wet sanding.
– When using a cable reel, make
sure to unroll the cable comple-
tely (wire diameter min. 1 mm
2).
– Disconnect the sander from the
power supply when work has
been completed.
– If the machine is defective, have
it serviced by a qualified dealer
immediately.
On/Off switch
On: Press trigger A.
Continuous Lock trigger A with locking
operation: button B.
Off: Briefly depress trigger A.
GB
Anleitung EOS 170 02.11.2001 10:24 Uhr Seite 2
3
Note!
Always wear safety goggles and a
dust mask.
Always keep the dust extraction holes
in the vibrating plate free of dirt or
other obstructions.
In order to take full advantage of your
vibrating sander, always use original
accessories, available at most hard-
ware shops.
Attaching sandpaper
– Remove the plug from the mains
supply.
– Insert the end of the sandpaper and
close the clamping mechanism.
– Draw the sandpaper tight over the
vibrating plate and clamp the other
end.
– Ensure that the holes match with the
vibrating plate.
Maintenance
– Always keep your orbital sander
clean.
– Do not use caustic cleaning agents
to clean the plastic housing.
– Check the carbon brushes if any
excessive amount of sparks are
generated when working.
– Always keep the dust extraction
holes in the vibrating plate free of
dirt or other obstructions.
– Water must never come into contact
with the machine.
GB
Anleitung EOS 170 02.11.2001 10:24 Uhr Seite 3


Produktspezifikationen

Marke: Power Craft
Kategorie: Sander
Modell: EOS 170

Brauchst du Hilfe?

Wenn Sie Hilfe mit Power Craft EOS 170 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Sander Power Craft

Bedienungsanleitung Sander

Neueste Bedienungsanleitung für -Kategorien-