POSline SM2430 Bedienungsanleitung
POSline
Barcode lezer
SM2430
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für POSline SM2430 (25 Seiten) in der Kategorie Barcode lezer . Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/25
Manual del Usuario
SM2430
ESPECIFICACIONES SUJETAS A CAMBIO SIN PREVIO AVISO.
i
No warranty of any kind is made in regard to this material, including, but not limited to, implied
warranties of merchantability or fitness for a particular purpose. We are not liable for any errors con-
tained herein nor incidental or consequential dam furnishing, performance ages in connection with
or use of this material.
No part of this document may be reproduced, transmitted, stored in a retrieval system, tran-
scribed, or translated into any language or computer language in any form or by any means elec-
tronic, mechanical, magnetic, optical, chemical, manual or otherwise, without express written
consent and authorization.
We reserve the right to make changes in product design without reservation and without notifi-
cation. The material in this guide is for information only and is subject to change without notice.
All trademarks mentioned herein, registered or otherwise, are the properties of their various
respective owners.
Copyright © 2004. All rights reserved.
Radio Notice
This equipment generates, uses and can radiate radio frequency energy. If not installed and
used in accordance with the instructions in this manual, it may cause interference to radio commu-
nications. The equipment has been tested and found to comply with the limits for a Class A comput-
ing device pursuant to EN55022 and 47 CFR, Part 2 and Part 15 of the FCC Rules. These
specifications are designed to provide reasonable protection against interference when operated in
a commercial environment.
Radio and Television Interference
Operation of this equipment in a residential area can cause interference to radio or television
reception. This can be determined by turning the equipment off and on. The user is encouraged to
try to correct the interference by one or more of the following measures:
* Reorient the receiving antenna.
* Relocate the device with respect to the receiver.
* Move the device away from the receiver.
* Plug the device into a different outlet so that the device and the receiver are on different
branch circuits.
If necessary the user may consult the manufacturer, an authorized dealer, or experienced
radio/television technician for additional suggestions. The user may find the following booklet pre-
pared by the Federal Communications Commission helpful: “How to Identify and Resolve Radio-TV
Interference Problems.” This booklet is available from the U.S. Government Printing Office, Wash-
ington, DC 20402 U.S.A., Stock No. 004000003454.
For CE-countries
This scanner is in conformity with CE standards. Please note that an approved, CE-marked
power supply unit should be used in order to maintain CE conformance.
ii
Laser Safety
The Dual-Laser Omnidirectional Vertical Scanner complies with safety standard
IEC 60825 for a Class I laser product. It also complies with CDRH as applicable
to a Class IIa laser product. Avoid long term staring into direct laser light.
Radiant Energy: The Dual-Laser Omnidirectional Vertical Scanner uses two
low-power visible laser diodes operating at 650nm in an opto-mechanical scan-
ner resulting in less than 3.9µW radiated power as observed through a 7mm
aperture and averaged over 10 seconds.
Do not attempt to remove the protective housing of the scanner, as unscanned
laser light with a peak output up to 0.8mW would be accessible inside.
Laser Light Viewing: The scan window is the only aperture through which
laser light may be observed from this product. A failure of the scanner motor,
while the laser diode continues to emit a laser beam, may cause emission lev-
els to exceed those for safe operation. The scanner has safeguards to prevent
this occurrence. If, however, a stationary laser beam
is emitted, the failing scan -
ner should be disconnected from its power source immediately.
Adjustments: Do not attempt any adjustments or alteration of this product. Do
not remove the protective housing of the scanner. There are no user-service-
able parts inside.
Caution: Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous laser light exposure.
Optical: The use of optical instruments with this product will increase the eye
hazard. Optical instruments include binoculars, magnifying glasses, and micro-
scopes but do not include normal eye glasses worn by the user.
Produktspezifikationen
| Marke: | POSline |
| Kategorie: | Barcode lezer |
| Modell: | SM2430 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit POSline SM2430 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Barcode lezer POSline
13 August 2024
13 August 2024
13 August 2024
13 August 2024
13 August 2024
13 August 2024
13 August 2024
13 August 2024
13 August 2024
13 August 2024
Bedienungsanleitung Barcode lezer
- Barcode lezer Manhattan
- Barcode lezer Trimble
- Barcode lezer Nilox
- Barcode lezer Motorola
- Barcode lezer Casio
- Barcode lezer Honeywell
- Barcode lezer Datamax-O'neil
- Barcode lezer Intermec
- Barcode lezer Zebra
- Barcode lezer Deltaco
- Barcode lezer IFM
- Barcode lezer Datalogic
- Barcode lezer Steren
- Barcode lezer Posiflex
- Barcode lezer Newland
- Barcode lezer Atlantis Land
- Barcode lezer Brady
- Barcode lezer Godex
- Barcode lezer Socket Mobile
- Barcode lezer QUIO
- Barcode lezer Argox
- Barcode lezer CipherLab
- Barcode lezer Code Corporation
- Barcode lezer Wasp
- Barcode lezer EC Line
- Barcode lezer Vultech
- Barcode lezer Bluebird
- Barcode lezer Mach Power
- Barcode lezer DENSO
- Barcode lezer Baracoda
- Barcode lezer IC Intracom
- Barcode lezer Opticon
Neueste Bedienungsanleitung für -Kategorien-
13 September 2024
13 September 2024
12 September 2024
6 September 2024
6 September 2024
6 September 2024
6 September 2024
5 September 2024
5 September 2024
5 September 2024