POSline ITT4050B Bedienungsanleitung
POSline
Etikettendrucker
ITT4050B
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für POSline ITT4050B (3 Seiten) in der Kategorie Etikettendrucker. Dieser Bedienungsanleitung war für 21 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/3
Label Printer
Page 1 of 2
Quick Installation Guide
Printer Overview
Setting up the Printer
(1) Connect the printer to the
computer mainframe.
(2) Plug the power cord into the
power jacket at the rear of the
printer.
(3) Plug the power cord into a
properly ground receptacle.
Note: Please switch OFF printer power switch prior to plug in the power cord to printer power jack.
Loading the Ribbon
(1) Place an empty paper core onto
the ribbon rewind spindle.
(2) Insert the left side first. Mount
the ribbon rewind paper core on
the front hubs.
(3) Please be noted that the bigger
hub side with 4 ribs must be
installed toward the right side of
ribbon mechanism.
(4) Install a ribbon on the ribbon
supply spindle. Mount the ribbon
supply spindle on the rear hubs.
(5) Insert the left side first. Please
be noted that the bigger hub
side with 4 ribs must be installed
toward the right side of ribbon
mechanism.
(6) Disengage the printer carriage
by pulling the carriage release
lever upwards.
(7) Following the direction of the
↓
↓
↓
↓↓
RIBBON
label, pull the
transparent ribbon leader to the
front from under the ribbon
mechanism.
(8) Attach the ribbon leader to the
empty paper core on the ribbon
rewind spindle (with a tape).
(9) Rotate the ribbon rewind spindle
until the ribbon overlaps the
ribbon leader and stretches
tight.
Ribbon rewind spindle
Ribbon supply spindle
Printer cover
Ribbon mechanism
Carriage release lever
Label supply spindle
Fixing tab
Print head
Label stripper
Backing paper outlet
Label roll mount
Page 2 of 2
Loading the Label
(1) Insert a label spindle into a paper
roll. Insert fixing tabs into the
spindle.
(2) Place the label onto the
(external) label roll mount.
(3) Install the label so that it goes
(when using an external label
roll mount: through the label
feed slot) in the direction of the
↓
↓
↓
↓↓ LABEL label and under the
ribbon mechanism to lay upon
the platen.
(4) Adjust the label guide to fit the
width of the label.
(5) Engage the printer carriage. (6) Close the printer cover.
Note: When switched on, the printer will automatically
detect whether ribbon is
installed to set printer
to direct thermal or thermal transfer mode. As such, to use thermal transfer mode, be sure to
install the ribbon, the label, and engage the ribbon mechanism before you switch on the printer.
To use direct thermal mode, install the label and engage the ribbon mechanism before switching
on the printer.
Power-on Utilities
î‚„ Self Test
Power off the printer, install the ribbon and the label first. Press the FEED button and then turn on the printer
power. Do not release the FEED button until the printer feeds labels. The printer performs the following items:
1. Calibrate label pitch.
2. Print out thermal print head check pattern.
3. Print the internal settings.
4. Enter into dump mode.
î‚„ Gap Sensor Calibration
This utility is used to calibrate the sensitivity of the gap sensor. Users may have to calibrate the gap sensor for
two reasons:
1. Using a new type of label
2. Initializing the printer
Note: The ERROR LED may flash if the gap sensor is not calibrated properly.
Please follow the steps below to calibrate the gap sensor.
1. Turn off printer power and install blank (i.e., without any logos or characters) label roll on the printer power.
2. Hold down the PAUSE button while turning on printer power.
3. Release PAUSE button when the printer feeds labels. Do not turn off printer power until the printer stops
and the two green LEDs light on.
î‚„ Printer Initialization
Printer initialization sets printer parameters to default values.
Please follow the steps below to initialize the printer:
1. Turn off the printer power.
2. Hold down the PAUSE
and FEED
buttons while turning on the printer power.
3. Do not release the buttons until the three LEDs flash in turn.
Note: When printer initialization is done, please calibrate the gap sensor again.
For further information on printer operation, please refer to the user's manual in driver CD disc.
Specifications, accessories, parts and programs are subject to change without notice.
Produktspezifikationen
| Marke: | POSline |
| Kategorie: | Etikettendrucker |
| Modell: | ITT4050B |
Brauchst du Hilfe?
Wenn Sie Hilfe mit POSline ITT4050B benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Etikettendrucker POSline
13 August 2024
8 Juli 2024
Bedienungsanleitung Etikettendrucker
- Etikettendrucker 3M
- Etikettendrucker Renkforce
- Etikettendrucker Seiko
- Etikettendrucker Toshiba
- Etikettendrucker Casio
- Etikettendrucker Citizen
- Etikettendrucker Olivetti
- Etikettendrucker Epson
- Etikettendrucker Honeywell
- Etikettendrucker Brother
- Etikettendrucker Leitz
- Etikettendrucker Phoenix
- Etikettendrucker Datamax-O'neil
- Etikettendrucker Dymo
- Etikettendrucker Intermec
- Etikettendrucker Primera
- Etikettendrucker SATO
- Etikettendrucker TSC
- Etikettendrucker Zebra
- Etikettendrucker Bixolon
- Etikettendrucker Datacard
- Etikettendrucker Esselte
- Etikettendrucker Nieaf-Smitt
- Etikettendrucker Toshiba TEC
- Etikettendrucker Panduit
- Etikettendrucker Brady
- Etikettendrucker Star Micronics
- Etikettendrucker Metapace
- Etikettendrucker Godex
- Etikettendrucker Start International
- Etikettendrucker Argox
- Etikettendrucker Dascom
- Etikettendrucker EC Line
- Etikettendrucker Tach-It
- Etikettendrucker Qoltec
- Etikettendrucker Qian
- Etikettendrucker SII
- Etikettendrucker Kroy
- Etikettendrucker Labelmate
- Etikettendrucker DULA
- Etikettendrucker Colop
- Etikettendrucker Custom
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
13 Oktober 2024
12 Oktober 2024
10 Oktober 2024
8 Oktober 2024
8 Oktober 2024
28 September 2024
22 September 2024