Planet IXT-705AT Bedienungsanleitung

Planet Nicht kategorisiert IXT-705AT

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Planet IXT-705AT (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

1. Package Contents

Thank you for purchasing PLANET Industrial 10G Media Converter.,

In the following section, unless specied, the term “Industrial

Media Converter” mentioned in this manual refers to the

IXT-705AT.

Open the box of the Industrial Media Converter and carefully

unpack it. The box should contain the following items:

Industrial Media

Converter x 1 User’s Manual x 1 DIN-rail Kit

Wall-mount Kit SFP+ Dust Cap x 1 RJ45 Dust Cap x 1

If any of these are missing or damaged, please contact your dealer

immediately; if possible, retain the carton including the original

packing material, and use them again to repack the product in case

there is a need to return it to us for repair.

2.ProductSpecications

Model IXT-705AT

Hardware Specications

Copper

Interface

1 x 10000/5000/2500/1000/100 BASE-T RJ45

Auto-MDI/MDI-X, auto-negotiation

Fiber Optic

Interface 1 10GBASE-SR/LR SFP+ interface

Connector

Removable 6-pin terminal block

Pin 1/2 for Power 1, Pin 3/4 for fault alarm, Pin

5/6 for Power 2

Alarm Provides one relay output for power failure

Alarm relay current carry capacity: 1A @ DC 24V

LED

System:

Fault Alert (Red), PWR (Green)

10000/5000/2500/1000/100 BASE-T RJ45

Interfaces

1/10G LNK (Orange)

5000/2500/100M LNK (Green)

ESD

Protection 6KV DC

Enclosure IP30 type metal case

Installation DIN-rail kit and wall-mount ear

Dimensions

(WxDxH) 32 x 87 x 135mm

Weight 458g

3.3 Converter Upper Panel

The upper panel of the IXT-705AT consists of one terminal block

connector within two DC power inputs. Figure 3-2 shows the upper

panel of the IXT-705AT.

Max. fault loading: 24V, 1A

V1+ V2+

PWR1 PWR2Fault

DC Input: 12-48V

, 0.6A max.

AC Input: 24V

, 0.2A max.

1 2 3 4 5 6

Figure 3-2: IXT-705AT Upper Panel

4. Hardware Installation

This section describes how to install the Industrial Media Converter

and makes connections to it. Please read the following sections and

perform the procedures in the order being presented.

This section describes the functionalities of the Industrial Media

Converter’s components and guides you to how to install it on

the DIN rail and wall. Basic knowledge of networking is assumed.

Please read this chapter completely before continuing.

4.1 Wiring the Power Inputs

The 6-contact terminal block connector on the top panel of

Industrial Media Converter is used for two DC redundant power

inputs. Please follow the steps below to insert the power wire.

3. Hardware Introduction

3.1 Physical Dimensions

IXT-705AT dimensions (W x D x H): 32 x 87 x 135mm

32.00

135.00

87.80

97.10

48.8046.50 39.70

28.00

48.80

53.50 53.50

18.00

15.20

30.00

9.20

40.00

28.0018.00

28.00

18.0028.00

28.00

40.00

Top View

Side View Front View Side View

Mounting Kit

DIN-Rail Kit

Unit: mm

Rear View

Bottom View

10G SFP+

10GBASE-T

2.5G

10G/1G

5G/100

FaultP2 P1

Max. f ault loading: 24V, 1A

V1+ V2+

PWR 1 PWR 2Fault

DC Input: 12-48V

, 0.6A max .

AC Input: 24V

, 0.2A max .

1.1 Product Features

IXT-705AT Physical Port

 1-port 10000/5000/2500/1000/100BASE-T RJ45 with auto

MDI/MDI-X function

 1-port 10GBASE-X SFP+

Layer 2 Features

 IEEE 802.3u/802.3ab/802.3bz/802.3ae Ethernet standard

compliant

 Supports auto-negotiation and 100Mbps half/full duplex and

1/2.5/5/10Gbps full duplex mode

 Prevents packet loss with back pressure (half-duplex) and

IEEE 802.3x pause frame ow control (full-duplex)

 16K jumbo frame size support

 Automatic address learning and address aging

Industrial Case and Installation

 Slim-type IP30 metal case

 DIN-rail or wall-mount design

 Redundant power design

 12 to 48V DC, redundant power with reverse polarity protection

 AC 24V power adapter acceptable

 Supports 6000 VDC Ethernet ESD protection

 100 meters over Cat 6A at 10Gbps

 -40 to 75 degrees C operating temperature

 Plug and Play installation

Power

Requirements DC 12~48V or 24V AC

Converter Specications

Flow Control Back pressure for half duplex

IEEE 802.3x pause frame for full duplex

Fabric 20Gbps

Address Table 9K entries, automatic source address learning and

aging

Jumbo Frame 16K

Network

Cables

10000/5000/2500/1000/100 BASE-T:

Cat5e, 6, 6A, 7 UTP cable (100 meters, max.)

EIA/TIA-568 100-ohm STP (100 meters, max.)

10GBASE-LR/SR/BX:

50/125μm or 62.5/125μm multi-mode ber

optic cable, up to 300m

9/125μm single-mode ber optic cable, up to

60km

Standards Conformance

Standards

Compliance

IEEE 802.3u 100BASE-TX

IEEE 802.3ab 1000BASE-T

IEEE 802.3bz 2.5G/5GBASE-T

IEEE 802.3an 10GBASE-T

IEEE 802.3ae 10Gbps Ethernet

IEEE 802.3x full-duplex ow control

Regulatory

Compliance FCC Part 15 Class A, CE

Stability

Testing

IEC60068-2-32 (Free fall)

IEC60068-2-27 (Shock)

IEC60068-2-6 (Vibration)

3.2 Converter Front Panel and LED Indicators

Figure 3-1 shows the front panels of the Industrial Media Converter.

10G SFP+

10GBASE-T

2.5G

10G/1G

5G/100

FaultP2 P1

Figure 3-1:

IXT-705AT

Front Panel

System

LED Color Function

P1 Green

Lit: Power 1 is active

O: Power 1 is inactive

P2 Green

Lit: Power 2 is active

O: Power 2 is inactive

FAULT Red

Lit: indicates either power 1 or

power 2 has no power.

O: No failure

Per 10000/5000/2500/1000/100BASE-T Port

LED Color Function

10/2.5/1G

Green Lit: To indicate that the port

is operating at 2.5Gbps.

Orange Lit: To indicate that the port

is operating at 10/1Gbps.

5G/100M Green

Lit: To indicate that

the port is operating at

5Gbps/100Mbps.

1. Insert positive / negative DC power wires into Contacts 1 and 2

for power 1 or 5 and 6 for power 2.

Max. fault loading: 24V, 1A

V1+ V2+

PWR1 PWR2Fault

DC Input: 12-48V

, 0.6A max.

AC Input: 24V

, 0.2A max.

1 2 3 4 5 6

V1+ V1- V2+ V2-

2. Tighten the wire-clamp screws for preventing the wires from

loosening.

1 2 3 4 5 6

Power 1 Fault Power 2

+ - + -

Note

The wire gauge for the terminal block should be in the

range between 12 and 24 AWG.

Note

1. The DC power input range is 12V ~ 48V DC and

supports 24V AC.

2. Please just use one power input when using 24V

AC.

- 9 -

- 10 -

- 11 -

- 12 - - 13 - - 14 -

6. Customer Support

Thank you for purchasing PLANET products. You can browse our

online FAQ resource on PLANET web site rst to check if it could

solve your issue. If you need more support information, please

contact PLANET switch support team.

PLANET online FAQs:

http://www.planet.com.tw/en/support/faq.php

Support team mail address:

support @planet.com.tw

Contents are subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp.

All other trademarks belong to their respective owners.

4.2 Wiring the Fault Alarm Contact

The fault alarm contacts are in the middle of the terminal block

connector as the picture shows below. When inserting the wires,

the Industrial Media Converter will detect the fault status of

the power failure and then forms an open circuit. The following

illustration shows an application example for wiring the fault alarm

contacts.

Fault Alarm Contacts

The Fault Alarm Contacts are

energized (CLOSE) for normal

operation and will OPEN when

failure occurs

Fault

Insert the wires into the fault alarm contacts

Note

1. The wire gauge for the terminal block should be in

the range between 12 and 24 AWG.

2. Alarm relay circuit accepts up to 24V, max. 1A currents

4.3 Grounding the Device

Users MUST complete grounding wired with the device; otherwise,

a sudden lightning could cause fatal damage to the device. EMD

(Lightning) DAMAGE IS NOT CONVERED UNDER WARRANTY.

4.4 DIN-rail Mounting Installation

This section describes how to install the Industrial Media Converter

on the DIN rail and wall. Basic knowledge of networking is

assumed. Please read this chapter completely before continuing.

5. Fiber and UTP Cable Connection

Installing the SFP+ Transceiver

The sections describe how to insert an SFP+ transceiver into an

SFP+ slot.

The SFP+ transceivers are hot-pluggable and hot-swappable. You

can plug in and out the transceiver to/from any SFP+ port without

having to power down the Industrial Media Converter

MTB Series

Transceiver

Figure 5-1: Plug in the SFP+ Transceiver

Note

It is recommended to use PLANET SFP+ on the

Industrial Media Converter. If you insert an SFP+

transceiver that is not supported, the Industrial Media

Converter will not recognize it.

Note

In the installation steps below, this Manual uses

PLANET 8-port Industrial Gigabit Switch IGS-801 as

the example. However, the steps for the installation

of PLANET Industrial Switch and Industrial Media

Converter are similar.

4.5 Wall-mount Plate Mounting

Caution

You must use the screws supplied with the wall-

mounting brackets. Damage caused to the parts by

using incorrect screws would invalidate your warranty.

10GBASE-X SR/LR:

Before connecting the other switches, workstation or Media

Converter, please do the following:

1. Make sure both sides of the SFP+ transceiver are with the

same media type; for example, 10GBASE-SR to 10GBASE-SR,

10GBASE-LR to 10GBASE-LR.

2. Check whether the ber-optic cable type matches the SFP+

transceiver model.

 To connect to 10GBASE-SR SFP+ transceiver, use the multi-

mode ber cable with one side being the male duplex LC

connector type.

 To connect to 10GBASE-LR SFP+ transceiver, use the single-

mode ber cable with one side being the male duplex LC

connector type.

Connecting the ber cable

1. Attach the duplex LC connector on the network cable to the

SFP+ transceiver.

2. Connect the other end of the cable to a device, switches with

SFP+ installed, ber NIC on a workstation or a Media Converter.

Note

Never pull out the module without pulling the lever

or the push bolts on the module. Directly pulling out

the module with effort could damage the module and

SFP+ module slot of the Industrial Media Converter.

100/1000/2500/5000/10000BASE-T

Connecting the UTP Cable

The 100/1000/2500/5000/10000BASE-T port uses RJ45 socket --

similar to phone jack -- for connection of unshielded twisted-pair

cable (UTP). See table below for required Category cables.

Standard Transfer Speed 100M Cable Requirement

10GBASE-T 10000Mbit/s Cat 6A/7

5GBASE-T 5000Mbit/s Cat 6/6A/7

2.5GBASE-T 2500Mbit/s Cat 5e/6/6A/7

1000BASET 1000Mbit/s Cat 5e/6/6A/7

100BASE-TX 100Mbit/s Cat 5/5e/6/6A/7

Note

Be sure the connected network devices support MDI/

MDI-X. If it does not support, then use the crossover

Category 5e cable.

Produktspezifikationen

Marke:	Planet
Kategorie:	Nicht kategorisiert
Modell:	IXT-705AT
Breite:	32 mm
Tiefe:	87 mm
Gewicht:	458 g
Produktfarbe:	Blau
Internationale Schutzart (IP-Code):	IP30
Übertragungstechnik:	Kabelgebunden
Höhe:	135 mm
Betriebstemperatur:	-40 - 75 °C
Relative Luftfeuchtigkeit in Betrieb:	5 - 95 %
Netzstandard:	IEEE 802.3ab, IEEE 802.3ae, IEEE 802.3an, IEEE 802.3bz, IEEE 802.3u, IEEE 802.3x
Zertifizierung:	FCC Part 15 Class A, CE
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	1
Warentarifnummer (HS):	85176990
Gehäusematerial:	Metall
Plug & Play:	Ja
Maximale Datenübertragungsrate:	20000 Mbit/s
Ethernet LAN Datentransferraten:	100,1000,2500,5000,10000 Mbit/s
Eingebaut:	Nein
LED-Anzeigen:	Alarm, Fault, Link, Power
Temperaturbereich bei Lagerung:	-40 - 75 °C
Luftfeuchtigkeit bei Lagerung:	5 - 95 %
Auto MDI/MDI-X:	Ja
Jumbo Frames Unterstützung:	Ja
Eingangsspannung:	12 - 48 V
Maximal mögliche Übertragungsstrecke:	100 m
Unterstützung Datenflusssteuerung:	Ja
Jumbo-Frames:	16000
Wellenlänge:	- nm
Optischer Kabelverbinder:	SFP+
Anzahl Faseranschlüsse:	1
DIN-Schienen-Montage:	Ja
Duplex-System:	Full, Half