Planet Audio PGR35B Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Planet Audio PGR35B (3 Seiten) in der Kategorie Hi-Fi-Anlage. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/3
1
2
4
5
3
6
PGR35B
USER MANUAL
FEATURING ZERO
STANDBY CURRENT DRAIN
QUICK INSTALLATION GUIDE
PGR35B
USER MANUAL
QUICK INSTALLATION GUIDE
BLUETOOTH® GAUGE HOLE RADIO
PRINTED IN CHINAVER:1.0 EN0215
The Bluetooth® word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks is under
license. Other trademarks and trade names are those of their
respective owners.
BEFORE YOU START
IMPORTANT SAFETY PRECAUTIONS
BE SURE TO OBSERVE THE FOLLOWING GUIDELINES:
Do not turn up the volume so high that you can’t hear what’s
around you.
Use caution or temporarily discontinue use in potentially
hazardous situations.
Do not operate mobile video equipment while driving a motorized
vehicle – safe driving and safety consideration of others should
always be your highest priority.
Set your volume control at a low setting, then slowly increase the
sound until you can hear it comfortably without distortion, or ear
discomfort.
In the event you should notice smoke, strange noises or odor from
this product, or any other abnormal signs, immediately turn off the
power and consult your dealer or the nearest authorized
PLANET AUDIO Service Center Using this product in this condition
may result in permanent damage to the system.
WIRE DIAGRAM
Thank you for purchasing this
PGR35B Bluetooth Gauge Hole Radio
Please read thorough these instructions
carefully so you will know how to operate
your model properly.
After you have nished reading the instructions,
keep this document in a safe place
for future reference.
SUGGESTED MOUNTING METHODS
INFORMATION TO THE USER
TROUBLE SHOOTING GUIDE
!! WARNING !!
ADJUSTMENT OR ALTERATIONS OF THIS DEVICE MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
B
A
ND
SRC
F
UNC
M
E
N
U
ENTER
DISP
VOL VOL
50w x4
US B
THIS PACKAGE CONTAINS
Fuse Box
15A
1A
CHARGING MAX
Replace Fuse
with AGU
type only
BATTERY
20A
Fuse and Fuse Holder
(not included)
Chassis
ground
point
Battery Kill Switch
(not included)
OPTIONAL DIRECT BATTERY WIRING CIRCUIT
BLACK
Chassis
ground
point
Ground wire
Metal frame
Recommended
12 ~ 14ga
Primary Wire
(not included)
15A
INSERT
YOUR
USB CABLE
YOUR
ANTENNA
C
NO
Normally open
ACC switch
(not included)
To avoid potential shorts in the electrical
system, be sure to disconnect the (–)
battery cable before installation. Use this
unit with a 12-Volt battery and negative
grounding only. Failure to do so may result
in a re or malfunction.
When replacing the fuse, be sure to only use a
fuse of the rating specied on this product. To
avoid short-circuiting, cover any disconnected
leads with insulating tape. It is specially impor-
tant to insulate any unused wires, which if left uncovered may cause a
short circuit. When connecting other devices to this product, refer to
the manual for the product to be connected. The black cable is ground,
make sure to connect the ground wire rst.
Ensure that the ground cable is properly connected to metal parts of
the vehicles body frame or direct to the battery if your vehicle does not
have a grounded chassis frame. The ground cable of this units power
amp and a second powered system must be connected to the frame
separately with different screws. If the screw for the ground wire
loosens or falls out, it could result in re or malfunction.
CAUTION!!
Do not ground or short the speaker leads
1-805-988-0215
www.planetaudiousa.com/support
TECHNICAL SUPPORT
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference
that may cause undesired operation of this device.
This transmitter must not be co-located or operated in conjunction
with any other antenna or transmitter. The Bluetooth antenna cannot
be removed (or replaced) by user. This equipment complies with
FCC/ IC radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure
Guidelines and RSS-102 of the IC radio frequency (RF) Exposure
rules. This equipment has very low levels of RF energy that it
deemed to comply without maximum permissive exposure
evaluation (MPE). But it is desirable that it should be installed and
operated keeping the radiator at least 20 cm or more away from
person’s body (excluding extremities: hands, wrists, feet and
ankles). Alteration or modications carried out without appropriate
authorization may invalidate the user’s right to operate the
equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Relocate or reorient the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC COMPLIANCE STATEMENT
1
32
TROUBLE CAUSE SOLUTION
Unit will not turn on
The fuse is blown Check / replace the fuse
Ignition not engaged Turn ignition to on position
No sound is heard
Blown speaker Replace faulty speaker
Volume is low / muted Press the volume level up
Device is paused or muted
Check your devices playing /
volume status
Cannot pair Bluetooth
The Bluetooth function of the
device is not enabled
Refer to the user manual of the
device for how to enable the
Bluetooth function
The PGR35B BT memory is full
Follow how to reconnect a
device in section E
The audio quality is poor
after connection with a
Bluetooth enabled device The Bluetooth reception is poor
Move the device closer to the
audio system or remove any
obstacle between the device
and the systems antenna
Unit has become
unresponsive
Power glitch or interference
Disconnect power for
10 seconds to reset
Low battery power
Charge battery, run the engine
to recharge the battery
Reset the main system Follow steps in section B
INSTALLATION PRECAUTIONS
Always consult with a professional installer
Do not attempt to install or service this product by yourself.
Installation or servicing of this product by persons without
professional training and experience in electronic equipment and mo-
torized vehicle accessories may be dangerous and could expose you
to the risk of electric shock, injury or other hazards
Refer any repairs to a qualied PLANET AUDIO Service Center
The should be wired directly to a vehicles battery PGR35B
When wiring directly to the vehicles battery, be sure to disconnect
the batteries negative terminal wire before starting any wiring
procedures, if extending the main power primary wire, it is
suggested that an optional fuse and fuse holder (not included) with
minimum rating of 20 Amperes be in-line with the positive battery
terminal
The ground cable length should be as short as possible, if
extending from you battery, be sure to use a proper gauge rating for
the length of the run, use only high quality copper primary type wire
The PGR35B has a IPX6 weather resistant design, it should not be
submerged in or under water under any circumstances
Do not use abrasive cleaning materials on the lens or bezel
Use only the installation parts provided with the PGR35B
TOOLS NEEDED:
- Measuring Tape / Ruler
- Wrench and/or Pliers
- Hole Saw
- Crimp Tool
CAUTION!!
Using other mounting methods may void
this warranty
FM TUNER FREQUENCY RANGE
USA 87.5~107.9MHz
Europe 87.5~108MHz
Asia 87.5~108MHz
Australia 87.5~108MHz
Usable Sensitivity: 12dB (S/N=30dB)
Bands: 2
AM TUNER FREQUENCY RANGE
USA 530~1710KHz
Europe 522~1620KHz
Asia 522~1620KHz
Australia 522~1620KHz
Usable Sensitivity: 40dB (S/N=20dB)
Bands: 1
WEATHER BAND SELECTION
CH.1 162.400MHz
CH.2 162.425MHz
CH.3 162.450MHz
CH.4 162.475MHz
CH.5 162.500MHz
CH.6 162.525MHz
CH.7 162.550MHz
Bands: 1
BLUETOOTH
BT: 3.0
BT Range: 33Ft / 10M (Class 2)
BT Proles: A2DP / AVRCP 1.3
USB DRIVE MEDIA SUPPORTED
MP3
WMA
65,000 Songs
32GB / FAT 32
USB 2.0 High Speed
USB Output Voltage: 5VDC @ 1A
INTEGRATED AMPLIFIER
MOSFET
MAX Continuous Output: 240W
(All channels driven)
PEAK Power Rating: 60W / channel
RMS Total Power Output: 80W
Channels: 4
Class: AB
Frequency Response: 20-20kHz
4Ω stable
CHASSIS
Button Backlight Illumination: BLUE LED
F/R/S RCA Preamp Output: 2VRMS
RCA Input Impedance: 10kΩ
LCD: TN Type / Active Matrix
GENERAL
Power Source: 14.4VDC
(10.8V ~ 16V allowable)
Grounding System: Negative type
Maximum Current Consumption: 15A
3-way protection circuitry (thermal,
overload, and speaker short protection)
Unit Weight: 1.08lbs / 0.52kg
Storage Temperature:
-22oF to 176oF / -30oC to 80oC
Operation Temperature:
-4oF to 158
oF / -20oC to 70oC
Replacement Fuse: 15A
(Replace with ATG Fuse Type Only)
SPECIFICATIONS
Specications subject to change without notice
QUICK START GUIDE
FOR CHARGING ONLY: Cell Phone and iPod
Media Playback Not Supported
iPod®
and iPhone® are registered trademarks of Apple Inc.
registered in the USA and other countries.
Planet Audio is not afliated with Apple Inc.
Copyright © 2015
AUDIO
xBas On/Ofs f
MID ve Le l
Tr e L lebl eve
Balanc evee L l
Fade ever L l
AUDIO
S rt Pressho
VOLVOL
VOL
VOL
VOL
VOL
VOLVOL
VOL
VOL
VOLVOL
AUDIO
Long Press
ENTER
DISP
VOL
VOL
ENTER
DISP
ENTER
DISP
EQ
BASS Level
SYSTEM
AUDIO
VOLVOL
S r S gsubwoofe ettin
ENTER
DISP
VOLVOL
VOL
VOL
ENTER
DISP
BLUETOOTH OPERATION
BLUETOOTH STREAMING MUSIC
PAIRING & DISCOVERING A NEW BLUETOOTH CONNECTION
1) Power on the PGR35B by pressing and holding down the Power button for 1 second, the Bluetooth
will start to ash signalling that the PGR35B is now ready for Bluetooth pairing.
NOTE: You have 2 minutes before you must restart this procedure over again.
2) Now that the PGR35B is in pairing mode:
ANDROID users:
a. Go into the Settings Menu of your ANDROID device
b. Enter the Bluetooth Menu and press SCAN
c. “MARINE RADIO” will now be display under AVAILABLE DEVICES
d. If prompted, enter passcode: “0000
iOS users:
a. Go into the Settings Menu of your iOS device
b. Enter the Bluetooth Menu
c. “MARINE RADIO” will now be displayed
d. If prompted, enter passcode: “0000
3) If the PGR35B is not seen, repeat the above steps to refresh the “Device List”
4) When the BT connection is successful you will see BT CONNECTED message on the PGR35B LCD displa
are now ready to stream music from your devices favorite media player to the PGR35B
RECONNECTION
1) Power on the PGR35B and your last paired device Bluetooth
2) The unit will now automatically be reconnected
3) If your device was previously paired with the PGR35B, but it wasn’t the last paired device:
a. Ensure no other devices are currently paired
b. Press and hold MENU button to manually connect / reconnect to the PGR35B
4) If the device is out of range from the PGR35B, it will disconnect automatically:
5)The PGR35B will reconnect to the device once in range, a conrmation message will be displayed on the
AUX-INPUT
1) Press the SRC button to select BT AUDIO
2) Press to start PLAY, press again to PAUSE
3) To skip songs or advance tracks press , press and hold to FAST FORWARD
4) To select the previous track press the button , press and hold to FAST REWIND
5) Press the
ENTE R
DISP
button to display song ID3 information
1) Press the SRC button to select AUX IN
2) Press to MUTE, press again to UNMUTE Ensure to adjust the level of
devices master volume to 7
Tips:
USB OPERATION
RADIO OPERATION
1) Press the SRC button to select USB
2) Press to start PLAY, press again to PAUSE
3) To skip songs or advance tracks press , press and hold to FAST FORWARD
4) To select the previous track press , press and hold to FAST REWIND
5) Press the
ENTE R
DISP
button to display song ID3 information
1) Press the SRC button to select RADIO
2) Press to MUTE, press again to UNMUTE
3) To advance stations press
4) To skip previous stations press
5) Press the
ENTE R
DISP
button to display RADIO information
6) Press the PRESET button to recall PRESETS 1 ~ 6
MY SONGS
SUBW
BT
TITLE
SUBW
USB
SUBW
AUX-IN
P6 10350
SUBW
LOCAL
RADIO
/ ,
SRC
PRESET
Fn
.
.
BAND
DISP
ENTER
AUDIO
VOL
VOL
VOL VOL
MENU
FM1, FM2, AM1, WB1
TUNER SETUP
BT
SUBW
SYSTEM
MY SONGS
SUBW
BT
A
B
D
E
F
G
H
MY SONGS
SUBW
BT
TITLE
SUBW
USB
SUBW
AUX-IN
P6 10350
SUBW
LOCAL
RADIO
C
VOL
VOL
ENTER
DISP
B
AN
D
MENU
AUDIO
VOL
VOL
ENTER
DISP
BA
ND
Fn
PRESET
ENTER
DISP
Fn
PRESET
PRESET AUTO STORE 1 ~ 6
PRESET RECALL
Fn
PRESET
Short Press
Long Press
ENTER
DISP
ENTER
DISP
VOLVOL
VOLVOL
ENTER
DISP
VOLVOL
ENTER
DISP
ENTER
DISP
ENTER
DISP
VOLVOL
VOLVOL
VOL
VOL
VOLVOL
ENTER
DISP
ENTER
DISP
MORE SETTINGS
FM1 / FM2 / AM1 / WB1
SOURCE MODES
All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any
form or by any means, including photocopying, recording, or other electronic or mechanical methods,
without the prior written permission of PLANET AUDIO.
To avoid battery exhaustion be sure to run the
vehicles engine while using this product.
Using this product without running the engine can drain the battery.
Tips:
PGR35B-UM-QSG-FINALv1.indd 2 1/25/2015 8:5


Produktspezifikationen

Marke: Planet Audio
Kategorie: Hi-Fi-Anlage
Modell: PGR35B

Brauchst du Hilfe?

Wenn Sie Hilfe mit Planet Audio PGR35B benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Hi-Fi-Anlage Planet Audio

Bedienungsanleitung Hi-Fi-Anlage

Neueste Bedienungsanleitung für -Kategorien-