Pioneer GM-ME400X4 Bedienungsanleitung

Pioneer Empfänger GM-ME400X4

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Pioneer GM-ME400X4 (14 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 24 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/14

PIONEER CORPORATION

28-8, Honkomagome 2-chome, Bunkyo-ku,

Tokyo 113-0021, JAPAN

Корпорация Пайонир

28-8, 2-Хонкомагомэ чоме, -Бункё ку,

Токио 113-0021, Япония

Импортер ООО ПИОНЕР РУС“ ”

105064, Россия г, . , , 5,Москва Нижний Сусальный переулок дом

строение 19

Тел.: +7(495) 956-89-01

PIONEER ELECTRONICS (USA) INC.

P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.

TEL: (800) 421-1404

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique

TEL: (0) 3/570.05.11

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

2 Jalan Kilang Barat, #07-01, Singapore 159346

TEL: 65-6378-7888

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

5 Arco Lane, Heatherton, Victoria, 3202 Australia

TEL: (03) 9586-6300

PIONEER ELECTRONICS DE MÉXICO S.A. DE C.V.

Blvd.Manuel Ávila Camacho 138, 10 piso

Col.Lomas de Chapultepec, México, D.F. 11000

TEL: 52-55-9178-4270

FAX: 52-55-5202-3714

先公鋒股份有限司

台北區市內湖瑞光路407 8號樓

電話：886-(0)2-2657-3588

先公鋒電限子（）香港有司

香港九龍長沙灣道909 5號樓

電話：852-2848-6488

Tous droits de reproduction et de

traduction réservés.

<5707000013050V> EL5

Visitez-nous sur le Web à

http://www.pioneer-car.eu

Pioneer Europe NV

Thank you for purchasing this PIONEER

product

To ensure proper use, please read through this

manual before using this product. It is espe-

cially important that you read and observe

WARNING CAUTIONs and s in this manual.

Please keep the manual in a safe and accessible

place for future reference.

If you want to dispose this product, do not mix

it with general household waste. There is a se-

parate collection system for used electronic

products in accordance with legislation that re-

quires proper treatment, recovery and recy-

cling.

Private households in the member states of

the EU, in Switzerland and Norway may return

their used electronic products free of charge

to designated collection facilities or to a retai-

ler (if you purchase a similar new one).

For countries not mentioned above, please

contact your local authorities for the correct

method of disposal.

By doing so you will ensure that your disposed

product undergoes the necessary treatment,

recovery and recycling and thus prevent po-

tential negative effects on the environment

and human health.

Information to User

Alteration or modifications carried out without

appropriate authorization may invalidate the

user s right to operate the equipment.’

Visit our website

Visit us at the following site:

http://pioneer.jp/en/info/globalnetwork/

We offer the latest information about

PIONEER CORPORATION on our website.

The Safety of Your Ears is in

Your Hands

Get the most out of your equipment by playing

it at a safe level a level that lets the sound—

come through clearly without annoying blar-

ing or distortion and, most importantly, with-

out affecting your sensitive hearing. Sound

can be deceiving. Over time, your hearing

“ ”comfort level adapts to higher volumes of

sound, so what sounds normal can actually“ ”

be loud and harmful to your hearing. Guard

against this by setting your equipment at a

safe level BEFORE your hearing adapts.

ESTABLISH A SAFE LEVEL:

!Set your volume control at a low setting.

!Slowly increase the sound until you can

hear it comfortably and clearly, without dis-

tortion.

!Once you have established a comfortable

sound level, set the dial and leave it there.

BE SURE TO OBSERVE THE FOLLOWING

GUIDELINES:

!Do not turn up the volume so high that you

can t hear what s around you.’ ’

!Use caution or temporarily discontinue use

in potentially hazardous situations.

!Do not use headphones while operating a

boat; the use of headphones may create a

traffic hazard and is illegal in many area-

Before you start

If you experience problems

Should this product fail to operate properly,

please contact your dealer or nearest author-

ized Pioneer Service Station.

Before connecting/

installing the amplifier

WARNING

!This product contains chemicals known to the

State of California and other governmental en-

tities tocause cancer and birth defects or

other reproductive harm. Wash hands after

handling.

!To prevent fire hazard, the heatsink should

never be covered with items (such as papers,

cloths).

!This unit is for the boats with a 12 V battery

and negative grounding. Before installing,

check the battery voltage.

!When installing this unit, make sure to con-

nect the ground wire first. Ensure that the

ground wire is properly connected to the

metal parts of the boat body. The ground wire

of the one of this unit must be connected to

the boat separately with different screws. If

the screw for the ground wire loosens or falls

out, it could result in fire, generation of smoke

or malfunction.

!Be sure to install the fuse to the battery wire.

!Always use a fuse of the rating prescribed.

The use of an improper fuse could result in

overheating and smoke, damage to the pro-

duct and injury, including burns.

!Check the connections of the power supply

and speakers if the fuse of the separately sold

battery wire or the amplifier fuse blows. Deter-

mine and resolve the cause, then replace the

fuse with and identical equivalent.

!Always install the amplifier on a flat surface.

Do not install the amplifier on a surface that

is not flat or on a surface with a protrusion.

Doing so could result in malfunction.

!When installing the amplifier, do not allow

parts such as extra screws to get caught be-

tween the amplifier and the boat. Doing so

could cause malfunction.

!Do not allow this unit to come into contact

with liquids. Electrical shock could result.

Also, damage to this unit, smoke, and over-

heating could result from contact with liquids.

The surfaces of the amplifier and any attached

speakers may also heat up and cause minor

burns.

!In the event of any abnormality, the power

supply to the amplifier is cut off to prevent

equipment malfunction. If this occurs, switch

the system power off and check the power

supply and speaker connections. If you are un-

able to determine the cause, please contact

your dealer.

!Always disconnect the negative terminal of*

the battery beforehand to avoid the risk of

electric shock or short circuit during installa-

tion.

!Do not attempt to disassemble or modify this

unit. Doing so may result in fire, electric

shock or other malfunction.

!Although this amplifier is designed specially

for marine applications, it is not submersible.

Do not install it in places that are prone to get-

ting wet.

!Do not install in places under direct sunlight,

places exposed to extreme heat or high hu-

midity, or places that will get wet.

!Attach a cover or cap to the terminals, and

prevent them from getting wet.

!Install the amplifier in a dry and well-venti-

lated environment, where other electrical ap-

pliances installed on the boat will not interfere

with it.

!When under direct sunlight with the cover on

for long hours, the cockpit area may have ex-

tremely high temperatures. Allows the area to

cool down after cover has been removed be-

fore using amplifier.

Before you start

Owner’s Manual

Mode d’emploi

MARINE 4-CHANNEL AMPLIFIER

AMPLIFICATEUR MARIN 4 CANAUX

GM-ME400X4

English

Français

CAUTION

!Always keep the volume low enough to hear

outside sounds.

!Extended use of the stereo while the engine is

at rest or idling may exhaust the battery.

!This product is evaluated in moderate and tro-

pical climate condition under the Audio, video

and similar electronic apparatus - Safety re-

quirements, IEC 60065.

!The graphical symbol placed on the

product means direct current.

About the protection function

This product has protection function. When this

product detects something abnormal, the follow-

ing functions will operate to protect the product

and speaker output.

!The indicator will turn redPOWER/PROTECT

and the amplifier will shut down in the situa-

tions outlined below.

—If the temperature inside the amplifier gets

too high.

—If a DC voltage is applied to the speaker

output terminal.

!The indicator will turn redPOWER/PROTECT

and the output will be muted in the situations

outlined below.

—If the speaker output terminal and speaker

wire are short-circuited.

What’s what

Front side

Rear side

To adjust the switch, use a flathead screwdri-

ver if needed.

1FREQ (cut off frequency) control

Cut off frequency selectable from 40 Hz to

500 Hz if the / select switch is set toLPF HPF

LPF HPFor .

2GAIN (gain) control

Adjusting gain controls (chan-CHANNEL A

nel A) and (channel B) helpsCHANNEL B

align the stereo output to the Pioneer ampli-

fier. Default setting is the posi-NORMAL

tion.

If the output remains low, even when the

stereo volume is turned up, turn the con-

trols to a lower level. If distortion occurs

when the stereo volume is turned up, turn

these controls to a higher level.

!If using only one input plug, set the gain

controls for speaker outputs A and B to

the same position.

!For use with an RCA equipped stereo

(standard output of 500 mV), set to the

NORMAL position. For use with an RCA

equipped Pioneer stereo, with maximum

output of 4 V or more, adjust level to

match that of the stereo output.

!For use with an RCA equipped stereo

with output of 4 V, set to the position.H

Before you start Setting the unit

3LPF (low-pass filter)/HPF (high-pass fil-

ter) select switch

Switch the settings based on the connected

speaker.

!When the Subwoofer is connected:

Select . This eliminates high rangeLPF

frequency and outputs low range fre-

quency.

!When the full range speaker is con-

nected:

Select orHPF OFF. eliminates lowHPF

range frequency and output high range

frequency. outputs the entire fre-OFF

quency range.

4INPUT SELECT (input select) switch

Select for two-channel input and2CH 4CH

for four channel input.–

5POWER/PROTECT indicator

The power indicator lights up to indicate

power ON.

!If something is not normal, the indicator

turns red.

Setting gain properly

!Protective function included to prevent

malfunction of the unit and/or speakers

due to excessive output, improper use or

improper connection.

!When outputting high volume sound etc.,

this function cuts off the output for a few

seconds as a normal function, but output

is restored when the volume of the head

unit is turned down.

!A cut in sound output may indicate impro-

per setting of the gain control. To ensure

continuous sound output with the head

unit at a high volume, set amplifier gain

control to a level appropriate for the preout

maximum output level of the head unit, so

that volume can remain unchanged and to

control excess output.

!Despite correct volume and gain settings,

the unit sound still cuts out periodically. In

such cases, please contact the nearest

authorized Pioneer Service Station.

Gain control of this unit

Preout level: 2 V (Standard: 500 mV)

Preout level: 4 V

Above illustration shows gain set-NORMAL

ting.

Relationship between amplifier gain

and head unit output power

If amplifier gain is raised improperly, this will

simply increase distortion, with little increase

in power.

Signal waveform when outputting at

high volume using amplifier gain

control

If the signal waveform is distorted due to high

output, even if the amplifier gain is raised, the

output power will change only slightly.

Setting the unit

Connection diagram

1Battery wire (sold separately)

!The maximum length of the wire be-

tween the fuse and the positive term-+

inal of the battery is 30 cm (12 in.).

!For the wire size, refer to Connecting the

power terminal. The battery wire, the

ground wire and the optional direct

ground wire must be same size. After

making all other connections at the am-

plifier, connect the battery wire terminal

of the amplifier to the positive term-+

inal of the battery.

2Fuse (60 A) (sold separately)

Each amplifier must be separately fused at

60 A.

3Positive terminal+

4Negative ( ) terminal*

5Battery (sold separately)

6Ground wire, Terminal (sold separately)

The ground wires must be same size as the

battery wire.

7Stereo with RCA output jacks (sold separately)

8External output

If only one input plug is used, do not connect

anything to RCA input jack B.

9Connecting wire with RCA pin plugs (sold se-

parately)

aRCA input jack A

bRCA input jack B

cAmplifier with RCA input jacks (sold sepa-

rately)

dRCA output jack

Outputs the signal input to .CH A

eSpeaker output terminals

Please see the following section for speaker

connection instructions. Refer to Connections

when using the speaker input wire.

fSystem remote control wire (sold separately)

gFuse (30 A) × 2

hFront side

iRear side

Note

INPUT SELECT (input select) switch must be set.

For details, see .Setting the unit

Before connecting the

amplifier

WARNING

!Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap sections

in contact with metal parts in adhesive tape.

!Never cut the insulation of the power supply

to feed power to other equipment. Current ca-

pacity of the wire is limited.

CAUTION

!To prevent water from entering the amplifier,

attach a cover or cap to each terminal when

not in use.

!Never shorten any wires, the protection circuit

may malfunction.

Connecting the units

!Never wire the speaker negative cable directly

to ground.

!Never band together multiple speaker s nega-’

tive cables.

!If the system remote control wire of the ampli-

fier is connected to the power terminal via the

ignition switch (12 V DC), the amplifier will re-

main on with the ignition whether the stereo

is on or off, which may exhaust battery if the

engine is at rest or idling.

!Install and route the separately sold battery

wire as far as possible from the speaker wires.

Install and route the separately sold battery

wire, ground wire, speaker wires and the am-

plifier as far away as possible from the anten-

na, antenna cable and tuner.

About bridged mode

!Do not install or use this amplifier by wiring

speakers rated at 2 (or lower) in parallel toW

achieve a 1 (or lower) bridged mode (Dia-W

gram B).

Amplifier damage, smoke, and overheating

could result from improper bridging. The am-

plifier surface could also become hot to the

touch and minor burns could result.

To properly install or use a bridged mode and

achieve a 2 load, wire two 4 speakers inW W

parallel with Left and Right (Diagram A)+ *

or use a single 2 speaker.W

In addition, refer to the speaker instruction

manual for information on the correct connec-

tion procedure.

!For any further enquiries, contact your local

authorized Pioneer dealer or customer

service.

About suitable

specification of speaker

Ensure speakers conform to the following

standards, otherwise there is a risk of fire,

smoke or damage. Speaker impedance is 2 W

to 8 W, or 4 W Wto 8 for two-channel and other

bridge connections.

Subwoofer

Speaker channel Power

Four-channel output Nominal input:

Min. 75 W

Two-channel output Nominal input:

Min. 200 W

Three-channel

output

Speaker output

Nominal input:

Min. 75 W

Speaker output

Nominal input:

Min. 200 W

Other than subwoofer

Speaker channel Power

Four-channel output Max. input:

Min. 150 W

Two-channel output Max. input:

Min. 400 W

Three-channel

output

Speaker output

Max. input:

Min. 150 W

Speaker output

Max. input:

Min. 400 W

Connecting the units

Produktspezifikationen

Marke:	Pioneer
Kategorie:	Empfänger
Modell:	GM-ME400X4

Brauchst du Hilfe?

Wenn Sie Hilfe mit Pioneer GM-ME400X4 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Empfänger Pioneer

Pioneer SX-303RDS Bedienungsanleitung

10 Oktober 2024

Pioneer DMH-340EX Bedienungsanleitung

18 September 2024

Pioneer A-10 Bedienungsanleitung

14 September 2024

Pioneer VSX-535 Bedienungsanleitung

2 September 2024

Pioneer DMH-C2550NEX Bedienungsanleitung

25 August 2024

Pioneer VSX-932 Bedienungsanleitung

25 August 2024

Pioneer AVH-P5050DVD Bedienungsanleitung

25 August 2024

Pioneer A-10EB Bedienungsanleitung

22 August 2024

Pioneer VSX-531D-B Bedienungsanleitung

20 August 2024

Pioneer DEH-3850MP Bedienungsanleitung

16 August 2024

Bedienungsanleitung Empfänger

Neueste Bedienungsanleitung für -Kategorien-

Rotel RA‑1592MKII Bedienungsanleitung

16 Oktober 2024

Denon AVR-S900W Bedienungsanleitung

16 Oktober 2024

Pro-Ject Amp Box DS2 Bedienungsanleitung

15 Oktober 2024

AKG HP12U Bedienungsanleitung

15 Oktober 2024

Sennheiser EM 9046 SU Bedienungsanleitung

14 Oktober 2024

Yamaha MusicCast RX-V481 Bedienungsanleitung

14 Oktober 2024

JL Audio VX600/6i Bedienungsanleitung

12 Oktober 2024

Technics SA-160L Bedienungsanleitung

8 Oktober 2024

Avantree Audiplex Bedienungsanleitung

7 Oktober 2024

Avantree Oasis Plus Bedienungsanleitung

7 Oktober 2024