Philips SpeedPro Max Aqua FC6903 Bedienungsanleitung

Philips Besen SpeedPro Max Aqua FC6903

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Philips SpeedPro Max Aqua FC6903 (2 Seiten) in der Kategorie Besen. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

3000.086.8922.1 (1/2022)

>75% recycled paper

>75% papier recyclé

FC6903

SpeedPro Max

Aqua

English

Congratulations on your purchase and welcome to Philips! To fully

benet from the support that Philips oers, register your product at

www.philips.com/MyVacuumCleaner.

Important safety information

Read this important information carefully before you use the appliance and its

accessories and save it for future reference. The accessories supplied may vary

for dierent products.

Danger

- Never vacuum up water or any other liquid. Never vacuum up ammable

substances and do not vacuum up ashes until they are cold.

- Never immerse the appliance or the adapter in water or any other liquid,

nor rinse it under the tap.

Warning

- Check if the voltage indicated on the adapter corresponds to the local mains

voltage before you connect the appliance.

- Always check the appliance before you use it. Do not use the appliance or

the adapter if it is damaged. Always replace a damaged part with one of the

original type.

- The adapter contains a transformer. Do not cut o the adapter to replace it

with another plug, as this causes a hazardous situation.

- This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

- Children should be supervised to ensure that they do not play with the

appliance.

- Keep the appliance and its cord out of the reach of children.

- Always keep the magnetic charging disc away from very small children.

- The plug must be removed from the socket-outlet before cleaning or

maintaining the appliance.

- Unplug the adapter if you are not going to use the appliance for some time.

- When storing the appliance for more than a month (without usage or

charging), make sure that the battery is charged to at least 50%. Storing

the appliance with an empty battery may lead to irreversible damage to the

battery.

- Also make sure that the adapter is unplugged when the appliance is stored.

- Do not let the motorized brush move over the mains cords of other appliances

or other cables as this may cause a hazard.

- Keep loose clothing, hair and body parts away from the motorized brushes.

- Do not cover or block the ventilation openings when the appliance is

operating.

- This vacuum cleaner is designed for household use only. Do not use this

vacuum cleaner to vacuum up building waste, cement dust, ashes, ne sand,

lime and similar substances. Never use the vacuum cleaner without any of

the lters. This could damage the motor and shorten the life of the vacuum

cleaner. Always clean all parts of the vacuum cleaner as shown in the user

manual. Do not clean any parts with water and/or cleaning agents if this is

not specically shown in the user manual.

- This product contains a rechargeable battery. The battery may only be

replaced by a qualied service engineer.

- Only charge the appliance with the adapter supplied. Only use 25V adapter

ZD12D250050 or 30V adapter ZD12D300050.

- Charge, use and store the product at a temperature between 5°C and 40°C.

- Do not open, modify, pierce, damage or dismantle the product or battery to

prevent batteries from heating up or releasing toxic or hazardous substances.

Do not short-circuit, overcharge or reverse charge batteries.

- Keep product and batteries away from re and do not expose them to direct

sunlight or high temperatures.

- If the product becomes abnormally hot or smelly, changes color or if charging

takes longer than usual, stop using and charging the product and contact

Philips.

- Do not place products and their batteries in microwave ovens or on induction

cookers.

- If batteries are damaged or leaking, avoid contact with the skin or eyes. If this

occurs, immediately rinse well with water and seek medical care.

- This product contains a rechargeable battery. The battery may only be

replaced by a qualied service engineer.

- Take the appliance to an authorized Philips service center when you can no

longer recharge it or when it runs out of power quickly.

- Do not open the appliance to replace the rechargeable battery.

- Take the appliance to an authorized Philips service center when you can no

longer recharge it or when it runs out of power quickly.

- To prevent damage, never put ethereal oils or similar substances in the water

tank or let the appliance pick them up.

- Do not lift or tilt the nozzle when the water tank is assembled and full, as

water may spray out of the water tank.

Caution

- During charging, the adapter becomes warm to the touch. This is normal.

- Do not plug in, unplug or operate the appliance with wet hands.

- Do not remove the adapter from the wall socket by pulling at the cord (Fig.1).

When you do not use the charging station for charging, always unplug the

appliance by rst detaching the magnetic charging disc from the underside of

the appliance (Fig. 2).

- Always switch o the appliance after use and before you charge it.

- Never block the exhaust air openings during vacuuming.

- Do not clean the dust container and the dust container lid in the dishwasher.

They are not dishwasher-proof.

- Do not clean the white material of the lter with a normal vacuum cleaner or

a brush to avoid damage to the material.

- Always use the vacuum cleaner with the lter assembled.

- When you clean the washable sponge lter with water, make sure it is

completely dry before you put it back into the lter holder and dust container.

Do not dry the sponge lter in direct sunlight, on the radiator or in the tumble

dryer. Do not clean the lter holder with water. This part is not washable.

- Replace the lter if it can no longer be cleaned properly or if it is damaged

(see ‚Ordering accessories‘).

- Never use any accessories or parts from other manufacturers or that Philips

does not specically recommend. If you use such accessories or parts, your

warranty becomes invalid.

- Make sure that the appliance is installed with the charging station attached to

the wall according to the instructions in the user manual.

- Be careful when you drill holes in the wall to attach the charging station, to

avoid the risk of electric shock.

- As this appliance uses water to clean, the oor may remain wet and slippery

for a while (Fig. 3).

- To prevent damage, do not use liquid oor cleaners that are not transparent

or even milky.

- To prevent damage, never put wax, oil, oor maintenance products or liquid

oor cleaners that are not water-dilutable in the water tank.

- Do not mix dierent types of liquid oor cleaner. When you have used one

liquid oor cleaner, rst empty and rinse the water tank before you add

another liquid oor cleaner to the water in the water tank.

- Never exceed the maximum quantities mentioned on the bottle when you

use a liquid oor cleaner. Do not add more than a few drops to the water in

the water tank, as this tank has a capacity of 200ml.

- Do not clean the metal wetting strip with a sharp object, as this may damage

the strip. Only clean the wetting strip by rinsing it under the tap. Replace the

wetting strip when you can no longer clean it.

- Replace the wetting strip only with an original strip. For ordering a new strip,

see chapter ‚Ordering accessories‘.

- Clean the water tank according to the instructions. The water tank is not

dishwasher-proof.

- Do not use aggressive cleaning agents or tools to clean the Aqua Boost pedal.

- After mopping the oors, do not store the appliance with the water tank

attached on the charging station. If you do this, the wet mopping pad will

touch the wall and this may damage the wall. Always remove the water tank

before you store the appliance.

- To guarantee good cleaning results and proper functioning of the appliance

and water tank, always use original Philips cleaning pads.

Electromagnetic elds (EMF)

This Philips appliance complies with all applicable standards and regulations

regarding exposure to electromagnetic elds.

Using the appliance

Usage restrictions

- Only use the water tank on hard oors with a water-resistant top coat (such

as linoleum, enameled tiles and varnished parquet) and stone oors (such as

marble). If your oor has not been treated to make it water-resistant, check

with the manufacturer if you can use water to clean it. Do not use the water

tank on hard oors of which the water-resistant top coat is damaged.

- Only use the water tank on linoleum oors that are properly axed to

prevent linoleum from being drawn into the mopping nozzle.

- Do not use the water tank to clean carpets.

- Do not move the appliance with water tank assembled sideways, as this

leaves water traces. Only move forwards and backwards.

Note: The operating time depends on the power level used during cleaning.

Mopping pad and wetting strip

The appliance comes with one wetting strip and two microber mopping pads.

With the water tank, wetting strip and microber mopping pad attached to the

standard oor nozzle, you can clean hard oors.

The aqua-colored mopping pad with wide stripes (FC8063) is suitable for

mopping stone and tiled oors. FC6903 comes with two FC8063 mopping pads.

Using liquid oor cleaner in the water tank

If you want to add a liquid oor cleaner to the water in the water tank, make

sure that you use a low-foaming or non-foaming liquid oor cleaner that can be

diluted in water. As the water tank has a capacity of 200ml, you only have to add

a few drops of liquid oor cleaner to the water.

Cleaning the water tank

To clean the water tank, mix one part vinegar with three parts water. Pour this

mixture into the water tank and close the cap. Shake the water tank and put the

water tank on a water-resistant surface. Leave the water-vinegar mixture in the

water tank overnight. Then empty the water tank, rinse it thoroughly with fresh

water, and use it normally again.

Caution: Water will leak from the water tank during cleaning, with and

without the wetting strip attached to the nozzle.

To empty the water tank, hold the water tank over a sink, remove the cap and

tilt the water tank to the side of the lling hole. Then turn the water tank over to

let the water ow into the sink. To remove the remaining water from the water

tank, turn the water tank on its long side with the lling hole pointing towards

the sink. Then tilt the water tank forwards to let the remaining water ow out of

the water tank.

Note: Always store the water tank with the cap removed from the lling hole.

Ordering accessories

To buy accessories or spare parts, visit www.philips.com/parts-and-accessories

or go to your Philips dealer. You can also contact the Philips Consumer Care

Center in your country (see the international warranty leaet for contact details).

Warranty and support

If you need information or support, please visit www.philips.com/support or

read the international warranty leaet.

Recycling

- Do not throw away the product with the normal household waste at the end

of its life, but hand it in at an ocial collection point for recycling. By doing

this, you help to preserve the environment.

- This product contains a built-in rechargeable battery which shall not be

disposed of with normal household waste. Please take your product to an

ocial collection point or a Philips service center to have a professional

remove the rechargeable battery.

- Follow your country’s rules for the separate collection of electrical and

electronic products and rechargeable batteries. Correct disposal helps prevent

negative consequences for the environment and human health.

Removing the rechargeable battery

Only remove the rechargeable battery when you discard the product.

Before you remove the battery, make sure that the product is

disconnected from the wall socket and that the battery is completely

empty.

Take any necessary safety precautions when you handle tools to open

the product and when you dispose of the rechargeable battery.

To remove the rechargeable battery, follow the instructions below.

1 Disconnect the appliance from the wall socket and let it run until the motor

stops.

2 Remove the dust container from the appliance (Fig. 5).

3 Undo the three screws that x the battery holder to the housing of the

appliance (Fig. 6).

4 Pull the battery holder out of the appliance (Fig. 7).

Troubleshooting

This chapter summarizes the most common problems you could encounter

with the appliance. If you are unable to solve the problem with the information

below, visit www.philips.com/support for a list of frequently asked questions or

contact the Consumer Care Center in your country.

Problem Possible cause Solution

The appliance does

not work when I

push the button.

When the battery is

empty, '00' ashes on

the display.

To charge the battery, connect

the appliance to the charging

base or attach the handheld

vacuum cleaner directly to the

magnet on the charging base.

You have to push

the slider forward

to switch on the

appliance.

Push the slider forward to

setting 1 to switch on. Increase

the suction power further by

pushing the slider to setting 2 or

select the turbo setting to clean

very dirty patches at the highest

suction power.

The appliance

suddenly stops

working.

When there is a

problem, the buttons

will not respond and

the screen will remain

blank.

Connect the appliance to the

charging station or attach the

handheld vacuum cleaner

directly to the magnet on the

charging station. Check the

display. Once the appliance

starts charging, you may

continue to use the appliance as

usual. If an error code appears,

you can nd its meaning in this

booklet.

The appliance has a

lower suction power

than usual.

The lter and the

cyclone are dirty.

Clean the lter and the cyclone.

The lter light lights up after

several hours of use to indicate

that you have to wash the

sponge lter. Make sure that

you wash the sponge lter at

least once a month if you use

the appliance regularly.

You have not attached

the dust container

lid properly to the

dust container. You

have not attached the

dust container to the

appliance properly. In

both cases, there will

be a loss of suction

power.

Make sure that you attach the

dust container lid to the dust

container and the dust container

to the appliance properly.

Dust escapes from

the appliance.

The lter is dirty. Clean the lter.

The lter is not

present in the

appliance.

Make sure that the lter is in

the appliance and assembled

correctly.

Something blocks the

cyclone.

Check the cyclone for objects

stuck in it and remove any

object that blocks the cyclone.

If dust falls out of the

dust container, the

dust container lid is

probably not attached

properly to the dust

container.

Empty the dust container and

attach the dust container lid

correctly.

The appliance does

not move smoothly

across the oor

when cleaning a

carpet.

You selected a too

high suction power.

Reduce the suction power by

choosing setting 1.

The brush does not

turn anymore.

The brush encounters

too much resistance.

Clean the brush with a pair of

scissors or by hand.

The brush may stop

turning when it

encounters too much

resistance from high-

pile carpet.

Switch o the appliance ad then

switch it back on again.

You have not installed

the roller brush in the

nozzle properly after

cleaning.

Follow the instructions in the

cleaning chapter of the user

manual to slide the roller brush

into the nozzle properly and

secure it inside the nozzle by

snapping home the locking

lever.

The LEDs in the

nozzle do not come

on.

You have not attached

the nozzle to the

appliance or handheld

properly.

Attach the nozzle to the

appliance or handheld properly.

The appliance is not

charging.

The magnetic

connector is not not

connected correctly

to the charging disk

or the adapter is not

inserted into the wall

socket properly.

Make sure that the magnetic

connector is connected properly

to the charging disk and that

the adapter is inserted into the

wall socket properly.

You have not

connected the correct

adapter and cord.

Make sure that you use the

correct adapter and cord.

If you have checked the above

and the appliance still does not

charge, take it to a Philips service

center or contact the Consumer

Care Center.

When I use my

vacuum cleaner

I sometimes feel

static electricity

shocks.

Your vacuum cleaner

builds up static

electricity. The lower

the air humidity, the

more static electricity

the appliance builds

up.

Discharge the appliance by

frequently holding the tube

against other metal objects in

the room (for example the legs

of a table or chair, etc.). You can

also raise the air humidity level

in the room.

The water ow from

the water tank is

reduced.

The wetting strip is

blocked by excessive

residue.

Remove the wetting strip and

clean it.

The microber

mopping pad is not

placed correctly and

blocks the wetting

strip as a result. This

prevents water from

owing out of the

wetting strip.

Make sure that you place the

mopping pad correctly. Check

the user manual for proper

placement.

The water tank is

empty or nearly

empty.

Rell the water tank.

You use a microber

mopping pad that

is not supplied by

Philips.

Only use an original Philips

microber mopping pad. You

can buy these mopping pads in

the online Philips shop at www.

shop.philips.com/service or at

your Philips dealer.

The output of water

is faster and larger

than normal.

If the water tank

produces an

uncontrolled and

too large amount of

water, the cap of the

tank is probably not

closed properly.

Check the cap and make sure it

is fully and properly closed.

The strip is not placed

properly in the bottom

of the water tank.

Check the strip and make sure

that it is tted properly in the

bottom plate of the water tank.

The oor dries with

stripes when I use

the water tank.

You added too much

liquid cleaner to the

water.

Use only a few drops or use a

cleaner that foams less.

Error codes

Error code Meaning

E1 The appliance is stored or charged at a temperature below

5°C. Move the appliance to a warmer room. Do not store or

charge the appliance at a temperature below 5°C or above

40°C.

E4 The roller brush in the motorized oor nozzle as become

blocked and cannot turn freely. Switch o the appliance and

check the roller brush for obstructions.

E6 No current passes through the adapter.Check if the adapter is

inserted into the wall socket properly. If the adapter is inserted

properly and the charging disk (magnet) is attached properly

and the appliance does not start to charge, the adapter may

be defective. In that case, please contact the Consumer Care

Center or take the appliance to an authorized Philips service

center.

E7 You use the wrong adapter. Connect the correct adapter.

If the correct adapter does not work, please contact the

Consumer Care Center or take the appliance to an authorized

Philips service center.

SE Please take the appliance to an authorized Philips service

center.

www.philips.com/support

140-150 cm

Max. 40 C0

Min. 5 C0

1 2 3

5 hrs.

1 2

1 2 3

www.philips.com/support

CP0178/01

www.philips.com/support

67 8

www.philips.com/support

FC5005

2 3

www.philips.com/support FC5005

www.philips.com/support

CP0667/01

www.philips.com/support

XV1700/01

www.philips.com/support

CP0381/01

www.philips.com/support

3 ml

5 6

2 3

7 8

14 15

1 2

21 3

4 5 6

5 64

7 8 9

10 11

EN Descaling

DE Entkal nke

FR Détartrage

CZ Odvápnění

HU Vízkőmentesítése

PL Usuwanie kamienia

UK видалення накипу

12 hrs.

9 10

www.shop.philips.com/service

XV1700/01

1 2

1 2 3

Produktspezifikationen

Marke:	Philips
Kategorie:	Besen
Modell:	SpeedPro Max Aqua FC6903
Gewicht:	2732 g
Produktfarbe:	Blau
Akku-/Batterietechnologie:	Lithium-Ion (Li-Ion)
Energiequelle:	Akku
Geräuschpegel:	84 dB
Anzahl:	1
Akku-/Batteriespannung:	25.2 V
Maximaler Luftstrom:	1000 l/min
Ladezeit:	5 h
Reinigungsart:	Trocken
Staubbehälter Typ:	Beutellos
Staubkapazität:	- l
Abnehmbarer Handstaubsauger:	Ja
Schmutzaufnahmekapazität (Trockenanwendung):	0.6 l
Maximale Eingangsleistung:	- W
Laufzeit:	75 min
Staubsauger-Stabmontage:	Ja
Kapazität Flüssigkeitstank:	0.28 l