Peerless PS200 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Peerless PS200 (21 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/21
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
ISSUED: 06-08-07 SHEET #: 083-9004-4 05-25-10
Installation and Assembly:
Paramount™ A/V Component Shelf
Model: PS200
Maximum UL Load Capacity:
100 lb (45.4 kg)
This product is intended for use with UL
Listed products and must be installed by a
quali ed professional installer.
2 of 21 ISSUED: 06-08-07 SHEET #: 083-9004-4 05-25-10
Note: Read entire instruction sheet before you start installation and assembly.
Tools Needed for Assembly
stud nder ("edge to edge" stud nder is recommended)
phillips screwdriver
drill
5/16" bit for concrete and cinder block wall
1/2" bit for metal stud wall
5/32" bit for wood stud wall
level
For customer care call (800) 865-2112 or (708) 865-8870.
Accessories (sold separately)
2 piece Metal Stud Fastener Kit (ACC 215) (Metal Stud
not evaluated by UL)
Safety Belt (ACC 322)
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Wood Stud Wall ................................................................................................................................................4
Installation to Solid Concrete or Cinder Block ........................................................................................................................5
Installing Support Arms and Wall Plate Cover ........................................................................................................................6
Installing Safety Belt (ACC 322 sold separately) ....................................................................................................................7
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum Load Capacity. See page one.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of
an "edge to edge" stud nder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
• This product was designed to be installed on the following wall construction only;
WALL CONSTRUCTION HARDWARE REQUIRED
Wood Stud Included
Wood Beam Included
Solid Concrete Included
Cinder Block Included
Metal Stud Do not attach except with Peerless Metal Stud Accessory Kit;
(not evaluated by UL)
Brick Contact Quali ed Professional (not evaluated by UL)
Other or unsure? Contact Quali ed Professional
WARNING
3 of 21 ISSUED: 06-08-07 SHEET #: 083-9004-4 05-25-10
DE
Before you begin, make sure all parts shown are included with your product.
Parts may appear slightly dierent than illustrated.
A
C
B
For mounting under a surface
Measure the height of the component to be placed onto
the mount, this measurement will be referred to as .H
Determine minimum distance from surface bottom to X
mounting hole centers using the formula X = H - 0.5" or
X = H - 13 mm
Note: If height of component is less than 4.5" (114
mm), a minimum distance of 4" (102 mm) is required for
X.
For mounting above a surface locate mounting hole
centers no less than 7.25" from surface top.
X = H - 0.5"
X = H - 13 mm
H
SIDE VIEW
1
E
X
B
7.25"
(184 mm)
MINIMUM
SURFACE TOP
SURFACE BOTTOM
DVD PLAYER,
AMPLIFIER, ETC.
F
PS200
Description Qty. Part #
A
support arm 2 083-0016
Bwall plate 1 083-P1019
Cwall plate cover 1 590-1281
Dconcrete anchor 2 590-0320
E#14 x 2.5" wood screw 2 5S1-015-C03
Fsafety belt 1 083-8015
Parts List


Produktspezifikationen

Marke: Peerless
Kategorie: Nicht kategorisiert
Modell: PS200

Brauchst du Hilfe?

Wenn Sie Hilfe mit Peerless PS200 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Peerless

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-