Peavey 6505 1992 Original Bedienungsanleitung
Peavey
Gitarrenverstärker
6505 1992 Original
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Peavey 6505 1992 Original (2 Seiten) in der Kategorie Gitarrenverstärker. Dieser Bedienungsanleitung war für 13 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
OPERATING GUIDE
SPEAKER CONNECTION
When connecting the amplifier to the speaker enclosure,
make. sure to set the impedance selector switch on the rear
of the unit to the impedance that matches your enclosure.
When two enclosures of equal impedance are used, set the
switch to one half the impedance of one enclosure (e.g.
two 16 ohm enclosures: set switch to 8 ohms; two 8 ohm
enclosures: set switch to 4 ohms). The 6505 1992 Original
is designed to operate into a minimum of 4 ohms.
EFFECTS PATCHING
USING THE EFFECTS LOOP
TO PATCH EXTERNAL,NON
GAIN PRODUCING
EFFECTS DEVICES
(DIGITAL DELAY, REVERS,
CHORUS, ETC.)
8 OHMS
SET SWITCH
TO 4 OHMS
8 OHMS
16 OHMS
SET SWITCH
TO 8 OHMS
16 OHMS
EFFECT(S) ARE
SELECTABLE USING
1992 ORIGINAL
6505 1992
Original REMOTE
FOOTSWITCH (See
section on REMOTE
FOOTSWITCH JACK)
FROM OUTPUT OF
RACK EFFECTS UNIT
TO 1992 ORIGINAL
6505 1992 Original
EFFECTS RETURN
INPUT
FROM 1992
ORIGINAL 6505
1992 Original SEND
OUTPUT TO INPUT
OF RACK EFFECTS
UNIT
IN OUT
SEND RETURN
RACK MOUNT EFFECTS UNIT
BACK PANEL
FLOOR PEDAL
OUT
IN
FROM OUTPUT OF
EFFECTS PEDAL
TO 1992 ORIGINAL
6505 1992 Original
EFFECTS RETURN
INPUT
FROM 1992
ORIGINAL 6505
1992 Original SEND
OUTPUT TO INPUT
OF EFFECTS PEDAL
SEND RETURN
SPECIFICATIONS
POWER AMPLIFIER SECTION
Rated Power & Load:
120 W RMS into 16, 8, or 4 ohms
Power @ Clipping:
(Typically @ 5% THD, 1 kHz, 120 V AC line)
130 W RMS into 16, 8, or 4 ohms
(Bias must be reduced to measure)
Frequency Response:
+0, -3 dB, 50 Hz to 20 kHz, @ 100 W RMS into 8
ohms
Hum & Noise:
Greater than 75 dB below rated power
Power Amp EQ:
Active Presence: +10 dB 2 kHz
Active Resonance: +10 dB @ cabinet resonant
frequency
Power Consumption: (Domestic)
400 watts 50/60 Hz, 120 V AC
PREAMP SECTION
The following specs are measured @ 1 kHz with the
controls preset as follows:
Low & High EQ @ 0
Bright out
Lead & Rhythm Post @ 10
Presence & Resonance @ 0 dB
Nominal levels with Pre Gains @ 5
Minimum levels with Pre Gains @ 10
Preamp High Gain Input:
Impedance: Very high Z, 470K ohms
LEAD CHANNEL (with channel select in)
Nominal Input Level: -80 dBV, -1 mV RMS
Minimum Input Level: 92 dBV. /025 mV RMS
CLEAN CHANNEL: (with channel select out)
Nominal Input Level: +34 dBV, 20 mV RMS
Minimum Input Level: -50 dBV, 3 mV RMS
Maximum Input Level: 0 dBV, 1.0 V RMS
(Subtract 16 dB with Crunch switch in)
Preamp Low Gain Input: (-6 dB pad)
Impedance: High Z 44K ohms
All levels are increased by +6 dB
Effects Send:
Load Impedance: 47K ohms or grater
Nominal Output: -10 dBV, 300 mV RMS
Effects Return:
Impedance: Very high Z, 470K ohms
Designed Level: -10 dBV, 300 mV RMS
Preamp Output:
Load Impedance: 47K ohms or grater
Nominal Output: +10 dBV, 3 V RMS
Remote Footswitch:
Special 2 button unit with LED indicators (supplied)
Channel select & Effects loop bypass
System Hum & Noise @ Nominal Level:
(Clean channel)
120 Hz to 20 kHz unweighted)
Greater than 74 dB below rated power
Equalization:
Custom Low, Mid & High passive type EQ Push
Bright, (Rhythm channel only)
+6 dB @ 2 kHz
Push Crunch (Rhythm channel only) Increases gain
Logo referenced in Directive 2002/96/EC Annex IV
(OJ(L)37/38,13.02.03 and defined in EN 50419: 2005
The bar is the symbol for marking of new waste and
is applied only to equipment manufactured after
13 August 2005
www.peavey.com
Warranty registration and information for U.S. customers available online at
www.peavey.com/warranty
or use the QR tag below
Features and specications subject to change without notice.
Peavey trElec onics Co orrp ation H5022 art ey l Peavey Drive ian, MS 05Merid 393 ) 5(601 483-536 FAX 01) -1 8(6 486 27
FCC/ICES Compliancy Statement
This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS Standard(s). Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received,
that may cause undesired operation.
Le présent appareil est conforme aux CNR d’lndustrie Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes: (1) I’appareil ne doit pas produire de brouillage, et (2) I’utilisateur de I’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Warning: Changes or modifications to the equipment not approved by Peavey Electronics Corp. can void the user’s authority to use the
equipment.
Note – This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
Congratulations! You have purchased
a rock & roll monster. The Peavey
6505® 1992 Original is the result
of an extensive research and
development to produce the ultimate
rock & roll guitar amp. You’re
ready to experience super rock
crunch, harmonic-rich sustain, and
screaming metal drive like you’ve
never heard from another amp.
Before you begin, please take the
time to read this operating guide,
familiarizing yourself with the 6505
1992 Original’s controls and
functions.
INPUTS
The 6505 1992 Original’s input
block features HIGH [1] and
NORMAL [2] gain inputs. The
HIGH gain input has twice
the gain of the NORMAL gain
input and should be used when
maximum overdrive is desired.
When both inputs are used
simultaneously, the 6505 1992
Original automatically switches to
the normal gain mode (6 dB pad).
Situations where both inputs are
used at once (alternating between
two guitars on stage using both
inputs, etc.) should be avoided if
peak overdrive is expected from
the amp. Experimentation with
your particular guitar/pickup into
each input will determine which
input is best for your sound.
CHANNEL SELECT SWITCH
Allows selection of the RHYTHM
or LEAD channel. Depressing
the switch to the “in” position
activates the LEAD channel. The
red LED light will illuminate to
indicate that the LEAD channel is
active. In the “out” position the
RHYTHM channel is activated
and the green LED illuminates.
Channels may be remotely
selected using the 6505 1992
Original’s footswitch. If remote
selection is desired the channel
select switch must be set to the
“in” position (LEAD channel).
LEAD PRE & POST GAIN
The LEAD CHANNEL PRE GAIN
[8] controls the input level and
works with the LEAD CHANNEL
POST GAIN [13] to determine the
overall volume/overdrive of the
LEAD channel. Lower settings of
the PRE GAIN control produce
a relatively clean, undistorted
sound while the middle to high
settings produce harmonically
rich distortion and screaming
overdrive/sustain. Since both PRE
and POST GAIN controls work in
“combo/’ a basic rule-of-thumb
set-up procedure is to begin
with both controls in the lower
settings (0 - 2). Using the PRE
GAIN control, dial in the amount
of overdrive/sustain you want
for the LEAD channel. Then, with
the POST GAIN control adjust for
overall volume.
RHYTHM PRE & POST GAIN
The RHYTHM channel PRE [4]
and POST GAIN [12] operate in
the same manner as the LEAD
channel gain controls. For most
applications, the RHYTHM
channel should be set up with
the PRE GAIN at the lower,
“cleaner” settings (0 - 4) and
the POST GAIN set for overall
volume. The RHYTHM channel
can be converted to a second
“lead” channel by activating the
CRUNCH SWITCH [6].
BRIGHT SWITCH
Activates a preset boost in the
treble frequencies (6 dB at 2
kHz) and affects only the rhythm
channel.
CRUNCH SELECT SWITCH
Boosts the gain of the rhythm
channel to create a second “lead”
channel. Depress to the “in”
position to activate.
EQUALIZATION
The 6505 1992 Original’s
equalization block features
passive LOW, MID, and HIGH EQ.
RESONANCE I PRESENCE
Unique to the 6505 1992 Original,
the RESONANCE [14] control can
be set to boost the gain of the
power amp in the low frequencies
at the resonance/attenuation point
of the speaker cabinet. In simple
terms, the RESONANCE control
works like a low EQ to offset
low-end frequency drop-out. The
PRESENCE [15] control works in
the same manner, boosting the
high frequencies. Experimentation
using your particular speaker
cabinet along with personal taste
will determine your setting for
these important controls.
STANDBY SWITCH
Allows the 6505 to be placed
in a non-operational standby
mode. When the standby switch
is activated, the tubes remain
hot and ready for instantaneous
operation, eliminating warm-up
time. The STANDBY LED indicator
light [16] will illuminate when the
amp is in the operational . mode
POWER SWITCH
Supplies power to the unit.
Depressed to the “ON” position,
the POWER LED indicator light
[17] will illuminate indicating
power is being supplied to the
unit.
FUSE
A 5 amp fuse is located within the
cap of the fuse holder. It must be
replaced with the same type and
value in order to avoid damage
to the equipment and to prevent
voiding the warranty. If the amp
repeatedly blows fuses, it should
be taken to a qualified service
center for repair.
WARNING: The fuse should only
be replaced when the power cord
has been disconnected from its
power source.
LINE CORD (120 V units only)
For your safety, we have
incorporated a 3-wire line (mains)
cable with proper grounding
facilities. It is not advisable to
remove the ground pin under any
circumstances. If it is necessary
to use the 6505 1992 Original
without proper grounding
facilities, suitable grounding
adaptors should be used. Greatly
reduced shock hazard exists
when the unit is operated with the
proper grounded receptacles.
GROUND SWITCH
Three position, rocker-type switch
which, for most applications,
should be operated in the center
(zero) position. If hum or noise
is noticed coming from the
speaker enclosure(s) with the
ground switch in the center
position, place the ground switch
to positive or negative (+or - ) to
minimize hum. Should a hum/
noise problem continue, consult
your authorized Peavey Dealer,
the Peavey factory, or a qualified
service technician. NOTE: The
ground switch is not functional
on 220/240 volt models.
EFFECTS SEND I EFFECTS
RETURN
Signals are supplied to outboard
effects or signal processing
units by patching from the
EFFECTS SEND [23] output into
the outboard unit(s) and back
into the EFFECTS RETURN [24]
input using shielded cable with
¼” phono jacks. Only non gain
effects devices (chorus, reverb,
delay, etc.) should be used in
the effects loop. Remote (on/
off) selection of outboard effects
devices can be achieved using the
6505 1992 Original’s footswitch.
PREAMP OUT
This output can be used to send
a preamped signal from the
6505 1992 Original to a mixing
console, tape recorder, etc., using
shielded cable. Patching from the
PREAMP OUT does not affect the
normal operation of the amplifier.
REMOTE FOOTSWITCH JACK
Provided for the connection of
the supplied remote footswitch.
When the footswitch is plugged
into the remote footswitch jack,
the channel select switch [3]
must be pressed to the “in”
position for remote selection to
operate. Remote selection of the
LEAD or RHYTHM channel (left
footswitch button) or outboard
devices in the effects loop (right
footswitch button) is possible
with the remote footswitch.
SPEAKER OUTPUTS
Paralleled ¼’’ OUTPUTS output
jacks for connecting speaker
enclosure(s) to the amplifier
(minimum: 4 ohms). When using
more than one enclosure, be sure
to calculate the total impedance
and set the impedance switch
[28] accordingly. (See section on
IMPEDANCE SWITCH.)
Important: Use only high quality,
Unshielded cable for speaker
connections.
IMPEDANCE SELECTOR
SWITCH
Use to select the appropriate
impedance of the speaker
enclosure(s). If two enclosures
of equal impedance are used, the
switch should be set at one half
of that value (e.g.,two 16 ohm
enclosures: set switch to 8 ohms;
two 8 ohm enclosures: set switch
to 4 ohms).
1
4
2
12
5
6
9
10
14
11
15
18
19
20
21
22
23
26 27 28
24
25
3
8
13
OPERATING GUIDE
1 3 6 10 28262420 27
18 21 23 25 2717151413121198542
1916
PUSH
CRUNCH
PUSH
BRIGHT
PRE POST
TUBE STAGES
CHANNEL
SELECT
FOOTSWITCH
FOOTSWITCH
LOW MID HI
RHYTHM
LEAD
TUBE BUFFER
EFFECTS
SEND
RETURN
TUBE STAGES
TUBE
POWER
AMP IMPEDANCE
SWITCH
OUTPUT
RESONANCE PRESENCE
PREAMP
OUT
SWITCH
LOGIC
TUBE STAGE
INPUT SWITCH
LOGIC
TUBE STAGES
SIGNAL FLOW BLOCK DIAGRAM
Produktspezifikationen
| Marke: | Peavey |
| Kategorie: | Gitarrenverstärker |
| Modell: | 6505 1992 Original |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Peavey 6505 1992 Original benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Gitarrenverstärker Peavey
19 September 2024
16 September 2024
6 September 2024
1 September 2024
1 September 2024
6 August 2024
3 August 2024
1 August 2024
30 Juli 2024
28 Juli 2024
Bedienungsanleitung Gitarrenverstärker
- Gitarrenverstärker Valeton
- Gitarrenverstärker Roland
- Gitarrenverstärker Vox
- Gitarrenverstärker Yamaha
- Gitarrenverstärker Marshall
- Gitarrenverstärker Fender
- Gitarrenverstärker Behringer
- Gitarrenverstärker Boss
- Gitarrenverstärker Line 6
- Gitarrenverstärker Radial Engineering
- Gitarrenverstärker Hartke
- Gitarrenverstärker ART
- Gitarrenverstärker Orange
- Gitarrenverstärker Harley Benton
- Gitarrenverstärker Electro Harmonix
- Gitarrenverstärker Blackstar
- Gitarrenverstärker Bugera
- Gitarrenverstärker TC Electronic
- Gitarrenverstärker Palmer
- Gitarrenverstärker Ampeg
- Gitarrenverstärker Laney
- Gitarrenverstärker SPL
- Gitarrenverstärker Ashdown Engineering
- Gitarrenverstärker Suhr
- Gitarrenverstärker AER
- Gitarrenverstärker Markbass
- Gitarrenverstärker EBS
- Gitarrenverstärker Fishman
- Gitarrenverstärker Voodoo Lab
- Gitarrenverstärker GR Bass
- Gitarrenverstärker Two Notes
- Gitarrenverstärker Hughes & Kettner
- Gitarrenverstärker Dimavery
- Gitarrenverstärker AMT
- Gitarrenverstärker Budda
- Gitarrenverstärker Empress Effects
- Gitarrenverstärker DACS Audio
- Gitarrenverstärker Rivera
- Gitarrenverstärker DV Mark
Neueste Bedienungsanleitung für -Kategorien-
3 Oktober 2024
3 Oktober 2024
3 Oktober 2024
3 Oktober 2024
3 Oktober 2024
23 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024