Peak PKC0J6 Bedienungsanleitung

Peak Ladegerät PKC0J6

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Peak PKC0J6 (7 Seiten) in der Kategorie Ladegerät. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/7
600 Peak Amp
Jump-Starter
Model No.: PKC0J6
Owner’s Manual
and Warranty Information
Read these instructions completely before using this product.
Retain this Owner’s Manual for future reference.
 Do not expose battery to fi re or intense heat since it can explode.
 Before recycling or disposing of a battery, protect exposed terminals with heavy-duty electrical tape
to prevent shorting (shorting can result in personal injury or fi re).
 Always wear protective eyewear when using this product. Contact with battery acid can cause
blindness and/or severe chemical burns.
 Follow these fi rst aid procedures in case of accidental contact with battery acid.
FIRST AID
SKIN: Wash skin thoroughly if battery acid comes in contact with skin. Seek medical attention
immediately.
EYES: Flush eyes with cool water for at least ten minutes. Seek medical attention immediately.
CONTACT POISON CONTROL CENTER IMMEDIATELY IF INGESTED.
 Never touch battery clamps together or to a common piece of metal. Sparking, explosion or
damage to the unit can result. Always store the battery clamps on the appropriate case clamp posts
on the back of the unit after use.
 Place this unit as far away from the battery being charged as the charging cables will permit.
 When using the Jump-Starter close to the vehicle’s battery and engine, place the unit on a fl at,
stable surface, and keep all clamps, cords, clothing and body parts away from moving parts of the
vehicle.
 Follow these instructions and those published by the battery manufacturer and manufacturer of
any equipment you intend to use near the battery. Pay attention to all hazard precautions on these
products and on the engine before charging.
 This system is designed to be used only on vehicles with a 12-volt DC battery system. Do not
connect to a 6-volt or 24-volt battery system.
 Remove all jewelry or metal objects that could cause short circuits or react with battery acid. A lead-
acid battery produces a short-circuit current high enough to weld a ring or other similar objects to
metal, causing a severe burn.
 When w orking on electrical equipment, always ensure someone is nearby to help you in an
emergency.
 Keep a supply of baking soda on hand when working on batteries. Baking soda neutralizes lead-
acid battery electrolyte.
All messages that follow have NOTICE level hazards. Failure to comply could
result in property damage.
 Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump-
started. Before jump-starting, read the vehicle’s owner’s manual to con fi rm that external-starting
assistance is suitable.
 Excessive engine cranking can damage a vehicle’s starter motor. If the engine fails to start after
the recommended number of attempts, discontinue these jump-start procedures and look for other
problems that may need to be corrected.
 This Jump-Star ter is not designed to be used as a replacement for a vehicle’s battery. Do not
attempt to operate a vehicle that does not have a battery installed.
 After connecting the batter y charging clamps to the discharged battery and before turning on the
jump-starter ON/OFF switch, check the power/polarity indicator light on the front of the unit. If the
light is GREEN, the clamp connections are correct. If the light is RED and an alarm sounds, the
clamp connections are incorrect and need to be reversed.
 This Jump-Starter is delivered in a partially charged state. Fully charge unit with the supplied
110/120-volt AC charger to the recommended maximum and initial charge time of 24 hours.
Thereafter, an AC typical charge time is 8 to 12 hours when using the AC charger.
 Although this unit contains a sealed batter y, it is recommended that unit be kept upright during
storage, use and recharging. To avoid possible damage that may shorten the unit’s working life,
protect it from direct sunlight, direct heat and/or moisture.
 Never allow battery acid to come in contact with this unit.
 All ON/OFF switches should be in the OFF position when charging the Jump-Starter or when not in
use. Make sure all switches are in the OFF position before connecting to a power source or load.
 Do not use any accessory that is not recommended or provided by the manufacturer.
INTRODUCTION
This Jump-Starter has been carefully engineered and manufactured to give you dependable operation.
Please read this manual thoroughly before operating your new Jump-Starter, as it contains the
information you need to become familiar with its features and obtain the performance that will bring you
continued enjoyment for many years. Please keep this manual on fi le for future reference.
FEATURES
 Built-in 600 peak amps batter y jump-starter with quick storing cables and clamps
 Built-in 12-volt DC power socket for powering DC appliances
 Built-in USB power outlet
 Batter y indicator display (indicates % of charge)
 Reverse polarity connection LED indicator with sound alarm
 Includes sealed, maintenance-fr ee, heavy-duty, lead-acid battery
 Requires no maintenance (other than recharging) for optimal operation
 110/120-volt AC charging plug
 Safe to use, transport and store
 Molded high-impact case is tough and durable
 Low Charge Alert (LCA)™
1
234
5
6
9
11
12
8
7
10
Legend
1. Jump-Starter/USB Port ON/OFF
Switch
2. Jump-Starter/USB Port ON LED
3. Battery Indicator Display
4. Display Button
5. 12-volt DC Power Socket
6. USB Port
7. Low Charge Alert (LCA) Port
8. Reverse Polarity Indicator LED
9. Low Charge Alert (LCA) Storage
Port
10. 110/120-volt AC Charging Plug
11. Red Positive (+) Jumper Cable
12. Black Negative (-) Jumper Cable
Low Charge Alert and LCA are trademarks of Old World Industries, LLC. Used with permission. All rights
reserved.

Produktspezifikationen

Marke: Peak
Kategorie: Ladegerät
Modell: PKC0J6

Brauchst du Hilfe?

Wenn Sie Hilfe mit Peak PKC0J6 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Ladegerät Peak

Peak

Peak PKC0J6 Bedienungsanleitung

13 August 2024
Peak

Peak PKC0AZ Bedienungsanleitung

27 Mai 2024

Bedienungsanleitung Ladegerät

Neueste Bedienungsanleitung für -Kategorien-

MSW

MSW S-CHARGER-20A.2 Bedienungsanleitung

16 Oktober 2024
MSW

MSW S-CHARGER-10A.2 Bedienungsanleitung

16 Oktober 2024
ABB

ABB EVLunic Bedienungsanleitung

9 Oktober 2024
Powerplus

Powerplus POWDP9062 Bedienungsanleitung

8 Oktober 2024
Cellular Line

Cellular Line Wireless Power Dock Bedienungsanleitung

7 Oktober 2024
HQ

HQ CHARGER14 Bedienungsanleitung

4 Oktober 2024
Makita

Makita DC18RD Bedienungsanleitung

4 Oktober 2024
HQ

HQ CH02E Bedienungsanleitung

2 Oktober 2024
Venom

Venom VS5007 Bedienungsanleitung

1 Oktober 2024
Venom

Venom VS5010 Bedienungsanleitung

1 Oktober 2024