Paxton Net2Air Bridge Bedienungsanleitung

Paxton WLAN-Repeater Net2Air Bridge

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Paxton Net2Air Bridge (4 Seiten) in der Kategorie WLAN-Repeater. Dieser Bedienungsanleitung war für 39 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

PAGE 1

Ins-40085-US Net2Air Ethernet bridge - UL

01/28/2013

The access control unit connects to the Net2 software running on the PC using Paxton Net2Air proprietary wireless

technology. A Net2Air bridge enables communication from the Net2 software to the Paxton wireless products.

Radio signals do not always behave as you might expect. For example, a cell phone that displays a full signal on

one part of the site will lose signal completely only a few feet away. These problems can be addressed by using the

Net2 site surveyor kit (690-200-US)

See also: XAN1095 - Net2 nano - How does it work? < http://paxton.info/974 >

X AN1096 - How to plan a Net2 nano installation < http://paxton.info/975 >

X Ins-30096-US - Net2Air site surveyor < http://paxton.info/1193 >

Net2Air wireless communication

Reader

Control unit

Net2Air Ethernet bridge

This unit is for supplemental use only, and is to be employed as a programming/downloading/monitoring tool only.

The unit will continue to operate in a 'standalone' mode if the PC is shut down. Any Events that occur during this

period are stored in the unit and the PC is updated when it comes back on line.

Part number Description

477-384-US Net2Air Ethernet bridge

Options

Paxton

Radio frequency

This product should not be installed within 10 feet of other wireless equipment operating on a 2.4Ghz frequency.

To ensure optimum performance other wireless networks should avoid WiFi channels 11, 12 and 13 to reduce the

possibility of interference.

**IMPORTANT - THIS IS A NETWORK DEVICE**

Please contact your IT Administrator before installing this product.

Technical Support

Technical help is available: Monday - Friday from 02:00 AM - 8:00 PM (EST)

1.800.672.7298 supportUS@paxton-access.com

Documentation on all Paxton products can be found on our web site - http://www.paxton-access.com/

For instructions in alternative languages - http://paxton.info/1000

PAGE 2

Enclosure

Power

Net2Air activity

TCP/IP LAN

connection

The bridge should be mounted vertically in the

supplied base to achieve the optimum range

Ethernet

Mac Address:

00-01-02-03-04

Access hole for reset button

Paxton

Access

Server Connected - The TCP/

IP interface is communicating

with the PC Net2 server

This equipment must not be co-located with any other transmitter and must be used at a distance in excess

of 20cm (7.9 inches) to the user.

The party that incorporates this equipment into another host device is responsible for verication of the

emissions produced by the nal product and must adhere to the limits specied in FCC Part 15.

Furthermore, a label must be applied to the exterior of the nal product referring to this enclosed module,

which states : "Contains FCC ID: USE477268"

Following the completed installation of this equipment, no further maintenance or testing is required.

It is advisable to ensure that any third party backup power supplies or recovery procedures are checked regularly

to ensure that the operation of the Paxton system is not compromised.

Maintenance

Fitting kits

Part number Description

fk1-088 2 off - No8 x 1in pozi round woodscrew - zinc

2 off - Wall plugs

Parts Kit

Power

Power Supply

Wiring methods shall be in accordance with the National Electrical Code (ANSI/NFPA70), local codes, and the

authorities having jurisdiction.

Power over Ethernet.

This unit can be powered over the ethernet link with POE compatible hardware. Where used, any POE injector

must be UL294 listed.

The unit is powered from a supplied mains power adaptor via a plug connection.

All interconnecting devices must be UL Listed.

The use of any add-on, expansion, memory or other module manufactured or supplied by the manufacturer's

representative will invalidate the CAN/ULC-S319 certication.

For CAN/ULC-S319 installations, terminals, leads and wiring methods must comply with CSA, C22.1, Canadian

electrical code, Part 1, safety standards for electrical installations.

PAGE 3

Click on and the MAC address of the device(s) will appear in the table. You must then use the "IP address ;Detect

conguration" tab to manually assign the IP address, subnet mask and gateway.

Be aware that if the IP address that you give the device is not in the same IP range as the PC, the device will no

longer respond until you connect to it with a PC that is in the same IP range.

Some rewall/virus protection software and other wireless hardware can block the IP detection process. Disable

these and try to detect the device again. Please contact Technical Support if you require further advice.

If you detect the MAC address but the device now shows 'Not Responding', you must check the IP address, to

make sure it is still in range with the PC or network. If it is not, you should either change the IP address of the

PC or the IP address of the device so they are both again in the same range. Our Technical team can talk you

through this if you need help.

If the MAC address does not appear when you click ensure that the following ports are open on all devices ;Detect,

between this unit and the Net2 PC:-

69 UDP

6486 TCP

6488 UDP

6489 UDP

Connecting to the PC via the Ethernet port

The IP address should be assigned a xed value, or should be given a DHCP reservation. Unreserved IP addresses

issued by DHCP servers are not guaranteed to be constant, leading to potential failure of communication between

Net2 software and the bridge.

To congure the unit, run the Net2 Server Conguration Utility (Start/Programs/Net2) and Click on Net2Air Bridge.

If you still cannot detect the MAC address of the device, connect it directly to your PC via a network cable and call

our Technical Help line.

This unit is designed to connect to an Ethernet port and supply the data at the required communications protocol

necessary for Paxton Net2 equipment.

Installation This unit is for Indoor use only

The unit is supplied in a plastic housing with a clip-on mounting (See Enclosure section). Suitable fasteners; two

screws and wall plugs are also provided if the base is to be xed to a wall or ceiling.

Sounder

The device will 'beep' when detected by the Net2 Server Conguration Utility or when new IP settings are applied.

The sounder will also respond to a direct 'Ping' over the network. This is a feature to assist with nding devices

hidden from view.

Produktspezifikationen

Marke:	Paxton
Kategorie:	WLAN-Repeater
Modell:	Net2Air Bridge
Produkttyp:	Netzwerkbrücke
Produktfarbe:	Black, Grey
AC Eingangsspannung:	100-240 V
Betriebstemperatur:	-20 - 55 °C
Netzstandard:	IEEE 802.3af
Power over Ethernet (PoE):	Ja
Maximale Datenübertragungsrate:	100 Mbit/s
Frequenzband:	2.4 GHz
Abmessungen (BxTxH):	70 x 100 x 195 mm
Wandmontage:	Ja