Panduit PED10B1 Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Panduit PED10B1 (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp
INSTRUCTIONS CM592A
© Panduit Corp. 2014
Door
Part Number Single Sided Dual Sided
PED6B1 PEVF6 PEV6
PED8B1 PEVF8 PEV8
PED10B1 PEVF10 PEV10
PED12B1 PEVF12 PEV12
Corresponding Vertical Manager
Page 1 of 5
PatchRunnerTM High Capacity Vertical Doors
Part Numbers: PED6B1, PED8B1, PED10B1, PED12B1, PED696B1, PED896B1,
PED1096B1, PED1296B1
Installation Instructions-Mounting Door to PEV Manager-
Step 3: Ensure that both handles are in the
disengaged position.
Handles
disengaged
Step 4: Set door onto ends of door bracket located
on the bottom of the manager. Then ensure that
activation tabs on the door bracket fit into windows
on the door.
Activation Tabs
Windows on door
Step 5: Fit activation tabs located on the top door
bracket into the windows located on top of the door.
Activation Tabs
Windows on door
Handles engaged
Step 6: Grasp fingers of manager with fingers and
apply thumb to door face. Then squeeze together
until handles pop into engaged position.
Step 1: Using a flat object, remove the grommets
from the rear of the door. The door brackets can
now be installed.
Door brackets
Remove grommets
Bottom of manager
Top of manager #12-24 Screws
Step 2: Install door brackets to manager as shown
using #12-24 screws Tighten screws to 15 in-lbs.
7FT Sizes
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTRUCTIONS CM592A
Installation Instructions-Mounting Door to PRV Manager-7ft Sizes
Door
Part Number Single Sided Dual Sided
PED6B1 PRVF6 PRV6
PED8B1 PRVF8 PRV8
PED10B1 PRVF10 PRV10
PED12B1 PRVF12 PRV12
Corresponding Vertical Manager
Step 1: Using a flat object, remove the grommets
from the rear of the door. The door brackets can
now be installed.
Door brackets
Remove grommets
Bottom of manager
Top of manager
#12-24 Screws
Step 2: Install door brackets to manager as shown
using #12-24 screws. Use holes closest to the front
of the manager. Tighten screws to 15 in-lbs.
Top Bracket
#12-24 Screws
Bottom Bracket
Outer holes
Step 3: Ensure that both handles are in the
disengaged position.
Handles
disengaged
Step 4: Set door onto ends of door bracket located
on the bottom of the manager. Then ensure that
activation tabs on the door bracket fit into windows
on the door.
Activation Tabs
Windows on door
Step 5: Fit activation tabs located on the top door
bracket into the windows located on top of the door.
Activation Tabs
Windows on door
Handles engaged
Step 6: Grasp fingers of manager with fingers and
apply thumb to door face. Then squeeze together
until handles pop into engaged position.
Page 2 of 5
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTRUCTIONS CM592A
Installation Instructions-Mounting Door to PEV Manager-8ft Sizes
PED696B1 PEVF696 PEV696
PED896B1 PEVF896 PEV896
PED1096B1 PEVF1096 PEV1096
PED1296B1 PEVF1296 PEV1296
Door
Part Number Single Sided Dual Sided
Corresponding Vertical Manager
Step 3: Ensure that both handles are in the
disengaged position.
Handles
disengaged
Step 4: Set door onto ends of door bracket located
on the bottom of the manager. Then ensure that
activation tabs on the door bracket fit into windows
on the door.
Activation Tabs
Windows on door
Step 5: Fit activation tabs located on the top door
bracket into the windows located on top of the door.
Activation Tabs
Windows on door
Handles engaged
Step 6: Grasp fingers of manager with fingers and
apply thumb to door face. Then squeeze together
until handles pop into engaged position.
Page 3 of 5
Step 1: Remove all brackets from the door. Identify
proper brackets for application and discard others.
Brackets used for mounting
to PRV Manager
No mark
Step 2: Install door brackets to manager as shown
using #12-24 screws. Use common brackets with “D”
cutout on the tongue. Tighten screws to 15 in-lbs.
Bottom of manager
Top of manager
#12-24 Screws
Common Bracket
with “D”
#12-24 Screws
Common Bracket
with “D”
Bottom bracketTop Bracket
Diamond
Bracket used for mounting
to PEV Manager (2 places)
Common Bracket
with “D”
“D” Shape


Produktspezifikationen

Marke: Panduit
Kategorie: Nicht kategorisiert
Modell: PED10B1
Breite: 257 mm
Tiefe: 38 mm
Produktfarbe: Schwarz
Höhe: 2104 mm
Gehäusematerial: Stahl
Nachhaltigkeitszertifikate: RoHS
Kompatibilität: PatchRunner
Rack-Kapazität: 45U

Brauchst du Hilfe?

Wenn Sie Hilfe mit Panduit PED10B1 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Panduit

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-