Panduit FSCRIBE Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Panduit FSCRIBE (11 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/11
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2018 FS119A
LC Fiber Optic Connectors
Field Polish Termination - Singlemode and Multimode
ITEM PART NUMBER DE CRIPTIONS
1 CST-115 Fiber C ble Ja acket tripperS
2 FALC Alcohol Bottle (empty)
3 S u SFBF P Fiber B ffer tripper
4 FLPT LC Crimp Tool
5 FS a SCRIBE C rbide cribe
6 FGLS Safety Gl eass s
7 FLCPK LC Poli hing P ck (1.25mm Ferr le)s u u
8FJPMR Primer
9 a sFJPXY An erobic Adhe ive
10 FH CT (or)S
FH CT-WS
He t hrink C ring Tool (110VAC / 60Hz for 1.6mm/2.0mm in t ll tion)a S u s a a
He t hrink C ring Tool (2 0VAC / 50Hz for 1.6mm/2.0mm in t ll tion)a S u 3 s a a
11 FK ArS amid Yarn S a she r
12 FPP5-L 5µm Poli hing Film (Als umin m Oxide)u
1 FPF1-V 1µm Di mond Poli hing Film3 a s
14 FLCPAD 5 D rometer Poli hing P8 u s ad
15 F CDVR crewdriverS S
16 F COPE 200x Micro copeS s
17 FLCA CP 1.25mm Ad pter for F COPES a S
1 F TY fety for fiber cr8 S Sa Stickers s a sp
1 F WB-C Cle ning w b9 S a S a s
20 F YR-X yringe with needle tipS S s s
21 FTWZR Tweezers
22 FWP-C Cloth Wipes
2 PFX-0 Indelible Ink M rking Pen3 a
24 FLOUPEX10 Eye Lo pe 10X Poweru
25 -- I opropyl Alcohol (Re gent Grs a a 9 ude, 0% minim m concentration; not av ila able from Pa und it)
26 FLCFPLF-X .05µm L pping Film (For inglemode termin tion only) a s a s
27 FWBTL Distilled Water Bottle (empty)
-- -- Distilled Wa ater (not va ail ble from Pa und it)
OPTIONAL PN 5* LC Connector 33 Stripping Template
DUPLEX
Duplex Clip
CONNECTOR ASSEMBLY
ITEMS REQUIRED FOR TERMINATION
SIMPLEX Dust cap
Connector Body
Backbone
Crimp Sleeve
900µm Boot
Jacketed Boot
with heat shrink
tubing
READ ALL INSTRUCTIONS COMPLETELY BEFORE PROCEEDING
Page 1 of 11
COMPONENT IDENTIFICATION
* denotes stripping template revision letter.
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2018 FS119A
TABLE OF CONTENTS Page(s)
Safety Precautions 2
900µm Tight-Buffered Fiber Termination 3-6
1.6mm - 2.0mm Jacketed Ca le Termination 7-11b
1. SAFETY GLASSES
WARNING: IT IS STRONGLY RECOMMENDED THAT SAFETY GLASSES BE
WORN WHEN HANDLING BARE OPTICAL FIBER. THE BARE FIBER IS VERY
SHARP AND CAN EASILY DAMAGE THE EYE.
2. ISOPROPYL ALCOHOL
WARNING: ISOPROPYL ALCOHOL IS FLAMMABLE. CONTACT WITH THE
ALCOHOL CAN CAUSE IRRITATION TO THE EYES. IN CASE OF CONTACT
WITH THE EYES, FLUSH WITH WATER FOR AT LEAST 15 MINUTES. ALWAYS
USE ISOPROPYL ALCOHOL WITH PROPER LEVELS OF VENTILATION. IN
CASE OF INGESTION, CONSULT A PHYSICIAN IMMEDIATELY.
3. RECOMMENDED ADHESIVE AND PRIMER
WARNING: THE RECOMMENDED ADHESIVE (PANDUIT PART# FJPXY) MAY
CONTAIN MALEIC ACID AND METHACRYLIC ESTER. IN CASE OF EYE
CONTACT, FLUSH WITH WATER FOR 15 MINUTES AND GET MEDICAL
ATTENTION. WASH SKIN AFTER CONTACT. REQUEST M.S.D.S. FOR
FURTHER SAFEGUARDS. CHECK “USED BY” DATE ON BOTTLE TO ENSURE
BEST PERFORMANCE.
WARNING: THE RECOMMENDED PRIMER (PANDUIT PART# FJPMR) MAY
CONTAIN ACETONE. THE PRIMER IS HARMFUL IF INHALED OR
SWALLOWED. IN CASE OF CONTACT WITH EYES OR SKIN, FLUSH WITH
WATER. GET MEDICAL ATTENTION IN CASE OF INGESTION OR CONTACT
WITH EYES. DO NOT INDUCE VOMITING. CHECK “USED BY” DATE ON
BOTTLE TO ENSURE BEST PERFORMANCE.
4. DISPOSAL OF BARE FIBERS
WARNING: PICK UP AND DISCARD ALL PIECES OF BARE FIBER WITH
STICKY TABS. DO NOT LET CUT PIECES OF FIBER STICK TO CLOTHING OR
DROP IN THE WORK AREA WHERE THEY ARE HARD TO SEE AND CAN
CAUSE INJURY.
5. LASER LIGHT PROTECTION
WARNING: LASER LIGHT IS INVISIBLE. THE INVISIBLE LIGHT IS POWERFUL
ENOUGH TO DAMAGE YOUR EYES. SERIOUS DAMAGE TO THE RETINA OF
THE EYE IS POSSIBLE. NEVER LOOK INTO THE END OF A FIBER WHICH MAY
HAVE A LASER COUPLED TO IT. SHOULD ACCIDENTAL EYE EXPOSURE TO
LASER LIGHT BE SUSPECTED, ARRANGE FOR AN EYE EXAMINATION
IMMEDIATELY.
6. CABLE HANDLING
WARNING: FIBER OPTIC CABLE CAN BE DAMAGED BY EXCESSIVE
PULLING, TWISTING, CRUSHING OR BENDING STRESSES. CONSULT THE
APPROPRIATE SPECIFICATION SHEETS AS PROVIDED BY YOUR CABLE
VENDOR. ANY DAMAGE MAY DECREASE OPTICAL PERFORMANCE.
CLASS II LASER
Page 2 of 11
SAFETY PRECAUTIONS
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2018 FS119A
1. PREPARING ADHESIVE AND PRIMER
1.1 Remove the plunger from a syringe. Squeeze about 0.5ml of
FJPXY Anaerobic Adhesive into the back of the syringe barrel.
Insert the plunger. Point opening upward, and squeeze any air
out of the barrel. Attach needle to syringe. Adhesive that is
stored in a syringe may start to harden within 24 hours.
2. STRIPPING 900µm TIGHT-BUFFERED FIBER
2.1 Insert the fi er end through the small end of the 900b µ bm oot.
Slide the b boot ack out of the way.
2.2 Following the stripping dimensions, use the marking pen to
place a mark .53" (13.5mm) from the end of the buffer.
2.3 With the fib ber uffer stripper provided, strip the buffer.
BUFFER STRIPPING GUIDELINES:
• Panduit recommends that you remove no more than
1/4" (6.4mm) of buffer at a time to avoid breaking the
fiber. Refer to cable manufacturer's buffer stripping
guidelines for specific recommendations.
• Hold the buffer stripper such that the arrow on the tool
points in the direction of buffer removal.
• Noting the location of the tool's blades, position the
fiber in the tool's V-notches. Squeeze the handles
firmly, and pull tool in the direction of the arrow on the
tool.
• Clean the buffer stripper blades after each strip by
holding the handles open, pulling the casings back
away from the blades, and letting them snap back
against the blades.
3. ATTACHING FERRULE TO 900µm TIGHT-BUFFERED FIBER
Instructions intended for anaerobic adhesive only.
3.1 Clean the bare fiber using an alcohol (90% minimum
concentration) soaked lint-free wipe. The fib bers should e free
of all coating and residue. Insert fiber without adhesive or
primer into ferrule assembly to ensure a proper fit and to
remove any debris which may b be locking the ferrule hole.
Remove fiber, clean fiber again, and proceed to the next step.
ADHESIVE
1.1
Page 3 of 11
1/4" (6.4mm) MAX 2.3
3.1
900µm Tight-Buffered Fiber Termination
900µm TIGHT-BUFFERED STRIPPING DIMENSIONS
IMPORTANT! Due to printing variations, use a rigid
Panduit laminated template.
scale for stripping dimensions, or the appropriate
2.2
2.1


Produktspezifikationen

Marke: Panduit
Kategorie: Nicht kategorisiert
Modell: FSCRIBE

Brauchst du Hilfe?

Wenn Sie Hilfe mit Panduit FSCRIBE benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Panduit

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-