Panduit FHC39N-08H-LAA Bedienungsanleitung

Panduit Nicht kategorisiert FHC39N-08H-LAA

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Panduit FHC39N-08H-LAA (3 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/3
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2015 FS117
Page 1 of 3
HD Flex LC Splice Cassette and
Fiber Adapter Panel (FAP)
Part Numbers: See chart below
Product Family Cassette Part
Number Cassette Description
12-Fiber LC Splice/FAP Cassette
(LC pigtails not included)
FHSXN-12-10N FAP (Fiber Adapter Panel) Cassette w/ Aqua Zirconia Adapters
FHS9N-12-10N FAP (Fiber Adapter Panel) Cassette w/ Blue Zirconia Adapters
12-Fiber LC Splice Cassette
(Pre-loaded with Discrete Pigtails)
FHSXO-12-10P 12-Fiber OM3 LC Discrete Pigtails; Optimized IL
FHSZO-12-10P 12-Fiber OM4 LC Discrete Pigtails; Optimized IL
FHSZA-12-10P 12-Fiber OM4 LC Discrete Pigtails; Ultra IL
FHS9N-12-10P 12-Fiber OS2 LC Discrete Pigtails; Standard IL
12-Fiber LC Splice Cassette
(Pre-loaded with Ribbon Pigtail)
FHSXO-12-10R 12-Fiber OM3 LC Ribbonized Pigtail; Optimized IL
FHSZO-12-10R 12-Fiber OM4 LC Ribbonized Pigtail; Optimized IL
FHSZA-12-10R 12-Fiber OM4 LC Ribbonized Pigtail; Ultra IL
FHS9N-12-10R 12-Fiber OS2 LC Ribbonized Pigtail; Standard IL

General Information and Contents
1. HD Flex LC Fiber Adapter Panel (FAP)
• Configured to accommodate pre-terminated cable assemblies.
2. HD Flex LC Preconfigured Splice Cassette – Available in 2 Configurations:
• Configured with 12 Discrete Pigtails, (12) 40mm Discrete Splice Sleeves, and 2 Pan-Ty Cable Ties.
• Configured with a 12-Fiber Ribbon Pigtail, (1) 40mm Ribbon Splice Sleeve, and 2 Pan-Ty Cable Ties.
WARNING: UNMATED CONNECTORS MAY EMIT INVISIBLE LASER RADIATION. MAINTAIN DUST CAPS ON UNMATED
CONNECTORS.
CAUTION:
Fiber optic cable is sensitive to excessive pulling, bending, and crushing forces. Consult the manufacturer’s cable specification sheet
for the specific cable in use.
Part Numbers
Cassette base Cassette cover Screw – Aramid yarn
strain relief
Cable tie strain relief
Cover removal latch
Splice sleeve holders
(12 discrete / 1 ribbon)
Cassette release latches
6 Duplex shuttered
LC Adapters
Figure 1
(Fibers not shown)
For complete HD Flex Fiber Cassette Enclosure installation instructions, visit www.panduit.com and search FS111*.
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2015 FS117
Page 2 of 3
1
2 3
4 5
6 7
8 9
10 11
12
(Front of Cassette)
Fiber Color Coding – Telcordia (Standard)
Fiber Color Key
Fiber 1 – Blue Fiber 7 – Red
Fiber 2 – Orange Fiber 8 – Black
Fiber 3 – Green Fiber 9 – Yellow
Fiber 4 – Brown Fiber 10 – Violet
Fiber 5 – Slate Fiber 11 – Rose
Fiber 6 – White Fiber 12 – Aqua

Figure 3
Patch cords
Install patch cords and route cables as shown.
Re-install cover.
Figure 2
Internal dust caps
Remove cover and internal dust caps.
It is recommended to use Panduit cable assemblies.
Note: When using jacketed patch cords, use
maximum cable diameter of 2.0mm and maximum
connector length of 2.0 inches (from end of ferrule to
end of boot).
FAP Termination – Fiber Adapter Panel Cassette
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2015 FS117
E-mail:
techsupport@panduit.com
Phone:
866-405-6654
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp www.panduit.com
Page 3 of 3
Figure 5
Incoming field Discrete splice sleeves
Routing tabs
Pan-Ty
Cable Ties
Kevlar
Cable jacket
(Ribbon sleeveoptional)
fibers
Strip incoming field cable outer jacket 20 inches.
Secure with Pan-Ty Cable Ties, and Kevlar with
screw (optional). Max cable diameter: 7.4mm
Expose all fiber ends for splicing. Slide a splice
sleeve onto either the (pigtail or field) fiber. Strip off
approximately 35mm of coating from each fiber.
Wipe the bare fiber with a lint-free tissue soaked with
isopropyl alcohol. Cleave the fiber so that 10mm
(both for 250µm and 900µm coating diameter) of
bare fiber extends past the fiber coating.
Note: Do not clean the bare fiber after it has been
cleaved, and do not let it come in contact with any
surfaces.
Splice all fibers and heat splice sleeve(s). Refer to
splicer manufacturer best practice instructions.
Route spliced fibers into cassette ensuring fibers
are located under the routing tabs. Incoming field
fibers are shown as black dashed lines.
Secure splice sleeves within splice organizer.
Re-install cover.
Figure 4
Screw
Pre-loaded pigtail fibers
Splice
organizer
(12 discrete)
Splice organizer (ribbon)
Pigtail Termination – LC Splice Cassettes
Remove the cover.
Pre-loaded pigtail fibers are shown as grey dashed
lines.


Produktspezifikationen

Marke: Panduit
Kategorie: Nicht kategorisiert
Modell: FHC39N-08H-LAA

Brauchst du Hilfe?

Wenn Sie Hilfe mit Panduit FHC39N-08H-LAA benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Panduit

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-