Panduit CT-160 Bedienungsanleitung
Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Panduit CT-160 (2 Seiten) in der Kategorie Niemals. Dieser Bedienungsanleitung war fĂĽr 46 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
CAUTION:
Verify power is “OFF” before working on wiring with this tool.
The plastic grips are for the user’s comfort,
and are not intended to insulate against electrical shock
while working on live electrical circuits.
CT-160
CRIMPING TOOL
OPERATION INSTRUCTIONS
10-32
.80
1.0
1.3
1.6
2.0
2
.6
MM
CUT COPPER ONL
Y
22
20
18
16
14
1
2
10
AWG
8-32
6
-32
M5
M4
M3
.5
INSULA
TION
AUTO
7
-8
MM
INS
INS
NO
N
INS
NO
N INS
12
-1 0
22
-1 4
12
-1 0
22
-1 4
CLO ESHERE
I
N
S
E
R
T
S
C
R
E
W
S
T
H
I
S
S
I
D
E
CT-160
NON-INSULATED BUTT SPLICE
INSTRUCTIONS
1. Insert stripped wire into end of the butt
splice to internal wire stop. (See product
packaging for proper strip lengths.)
2. Locate butt splice in proper non-
insulated crimp pocket.
3. Position crimp pocket on the center of
the metal barrel half with wire inserted.
4. Squeeze handles firmly.
5. Repeat for other end of butt splice.
Page: 1 of 2
PA24427A01
REV.: 02 5-2014
OPERATION INSTRUCTIONS
© Panduit Corp. 2014
CT-160
For Technical Support:
1-888-506-5400, ext. 83255
E-mail:
techsupport@panduit.com
See product packaging or contact Customer Service for
UL/CSA approved tooling/product combinations.
INSULATED BUTT SPLICE
INSTRUCTIONS
1. Insert stripped wire into end of the butt
splice to internal wire stop. (See product
packaging for proper strip lengths.)
2. Locate butt splice in proper insulated
crimp pocket.
3. Position crimp pocket on the center of
the metal barrel half with wire inserted.
4. Squeeze handles firmly.
5. Close insulation if desired.
6. Repeat for other end of butt splice.
WIRE STRIPPER for removing plastic or
rubber wire insulation. Strip length should
allow a minimum of 1/32” of conductor to
extend beyond terminal barrel.
WIRE CUTTER for No. 10 AWG and
smaller copper wire.
CUTTERS for machine screws of sizes
shown. Open handles, thread screw in this
side. Close handles to cut screw.
CRIMPING POCKETS for Pan-Term non-
insulated and insulated terminals,
disconnects, splices and wire joints on No.
22 to 10 AWG stranded wire. See product
packaging for proper crimping pockets.
This tool is made of hardened steel and is
protected with a light coat of oil.
NON-INSULATED AND INSULATED
PARALLEL SPLICE INSTRUCTIONS
1. Insert stripped wire into each end of the
parallel splice. (See product packaging
for proper strip lengths.)
2. Locate parallel splice in proper crimp
pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
CRIMP POCKET
CRIMP POCKET
CRIMP POCKET
CRIMP POCKET
NON-INSULATED
INSULATED
www.panduit.com
Page: 2 of 2
OPERATION INSTRUCTIONS
NON-INSULATED
TERMINAL AND DISCONNECT
INSTRUCTIONS
1. Insert stripped wire into terminal or
disconnect until a minimum of 1/32" of
conductor extends beyond barrel. (See
product packaging for proper strip
lengths.)
2. Locate terminal or disconnect in proper
non-insulated crimp pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
INSULATED
TERMINAL AND DISCONNECT
INSTRUCTIONS
1. Insert stripped wire into terminal or
disconnect until a minimum of 1/32" of
conductor extends beyond barrel. (See
product packaging for proper strip
lengths.)
2. Locate terminal or disconnect in proper
insulated crimp pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
5. Close insulation if desired.
NON-INSULATED WIRE JOINT
INSTRUCTIONS
1. Twist ends of stripped wire together,
trim and insert into wire joint. (See
product packaging for proper strip
lengths and trimming instructions.)
2. Locate wire joint in proper non-insulated
crimp pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
INSULATED WIRE JOINT
INSTRUCTIONS
1. Twist ends of stripped wire together,
trim and insert into wire joint. (See
product packaging for proper strip
lengths and trimming instructions.)
2. Locate wire joint in proper insulated
crimp pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
5. Close insulation if desired.
CRIMP POCKET
CRIMP POCKET CRIMP POCKET
CRIMP POCKET
CT-160
© Panduit Corp. 2014
NOTE:
In the interest of higher
quality and value, Panduit is
constantly improving and
updating our products.
Consequently, pictures herein may
vary from the actual product.
Produktspezifikationen
| Marke: | Panduit |
| Kategorie: | Niemals |
| Modell: | CT-160 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Panduit CT-160 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Niemals Panduit
28 Februar 2024
24 Dezember 2023
Bedienungsanleitung Niemals
- Niemals 3M
- Niemals Scarlett
- Niemals Leatherman
- Niemals Monoprice
- Niemals Gefen
- Niemals Park Tool
- Niemals Fixpoint
Neueste Bedienungsanleitung fĂĽr -Kategorien-
16 Juni 2024
15 Juni 2024
15 Juni 2024
18 Mai 2024
4 April 2024
28 März 2024
21 März 2024
20 März 2024
15 März 2024
28 Januar 2024