Panasonic WVST165 Bedienungsanleitung

Panasonic Überwachungskamera WVST165

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Panasonic WVST165 (2 Seiten) in der Kategorie Überwachungskamera. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
Option
Precautions for use Precautions for Installation
Standard accessories
This system is designed to be used indoors. This product is not operable outdoors.
This product has no power switch.
When turning off the power, disconnect the power supply from the 12 V DC power supply or the
PoE device. (When using both the 12 V DC power supply and the PoE device for power supply, dis-
connect both the connections.)
To keep on using with stable performance
Do not use this camera in hot and humid conditions for a long time. Failure to observe this causes
component degradation resulting in life shortening of this product.
Do not expose this camera to direct heat sources such as a heater.
Do not touch the lens cover with your bare hands.
A dirty lens cover causes deterioration of picture quality.
Handle this camera with care.
Do not drop this camera, nor apply shock or vibration to this camera. Failure to observe this may
cause trouble.
About the PC monitor
Displaying the same image on a monitor for a long time may damage the monitor. It is recommend-
ed to use a screen-saver.
When an error is detected, this product will restart automatically.
This product will be inoperable for around 2 minutes after the restart just as when the power is turned on.
Product disposal/transfer
Data saved on this product or a storage device used with this product may lead to personal
information leakage. When it is necessary to dispose or give this product to someone, even when
for repair, make sure that there is no data on this product.
Cleaning this product body
Be sure to turn off the power before cleaning. Failure to observe this may cause injury. Do not use
strong abrasive detergent when cleaning this product. Otherwise, it may cause discoloration. When
using a chemical cloth for cleaning, read the caution provided with the chemical cloth product.
When the dirt is hard to remove, use a damp cloth and wipe the dirty areas. Then, wipe with a dry
cloth to remove any moisture.
Transmission interval
Image transmission interval may become slow depending on the network environment,
PC performance, shooting subject, access number, etc.
About SD memory card
When using an unformatted SD memory card, format it using this camera. Recorded data on the
⿟
SD memory card will be deleted when formatted. If an unformatted SD memory card or an SD
memory card formatted with other devices is used, this product may not work properly or perfor-
mance deterioration may be caused. Refer to the Operating Instructions (included in the
CD-ROM) for how to format a SD memory card.
When some SD memory cards are used with this product, the product may not work properly or
⿟
performance deterioration may be caused. Use the SD memory cards recommended.
Code label
The code labels (accessory) are required at inquiry for trouble. Use caution not to lose these labels.
It is recommended to paste one of the labels onto the CD-ROM case.
About the MOS image sensor
When continuously shooting a bright light source such as a spotlight, the color lter of the MOS
⿟
image sensor may have deteriorated and it may cause discoloration. Even when changing the
xed shooting direction after continuously shooting a spotlight for a certain period, the discolor-
ation may remain.
When shooting fast-moving subjects or performing panning/tilting operations, objects crossing
⿟
the shooting area may look to be bending askew.
AVC Patent Portfolio License
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE
PERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE
REMUNERATION TO
(i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR
(ii)
DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL
ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC
VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL
INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C.
SEE HTTP://WWW.MPEGLA.COM
Flickering
Due to the inuence of lighting, ickering may sometimes happen. In this case, select “Indoor
scene” for “Light control mode”. Select “Indoor scene(50Hz)” or “Indoor scene(60Hz)” in accor-
dance with the power supply frequency in your locality. Refer to the Operating Instructions (included
in the CD-ROM) for further information about the setting.
Under extremely strong lighting, ickering may happen even when “Indoor scene” is selected for
“Light control mode”. When the brightness (illuminance) level on the screen is set to a relatively low
level with the [Brightness] buttons, ickering may frequently happen. In such cases, either of the fol-
lowing can reduce ickering.
Moderate the illumination intensities of objects by changing the camera direction.
⿟
⿟
Set the brightness (illuminance) level on the screen to a brighter level with the [Brightness] buttons.
White-out on images caused by the effect of light control mode
When “Indoor scene” is selected for “Light control mode”, the tone of the brighter parts on the
screen may be deteriorated than the case when “ELC” is selected.
Color blurring on detailed drawing patterns
When there are detailed drawing patterns on images, color blurring may happen over these parts.
Consumable parts
The following are consumables: Replace them in accordance with their lives. Their lives vary
depending on use environment and conditions. Lifetime is just an indication when using the camera
at +20 °C {68 °F}.
Panning motor, tilting motor, at cable for tilting: Approx. 3.7 million operations.
⿟
Lens and pan/tilt head
If a lens and pan/tilt head are not performed for a long period of time, the grease coating inside
these parts may become sticky. That may obstruct the parts from moving. To prevent this, move
the lens or pan/tilt head periodically.
Panasonic assumes no responsibility for injuries or property damage resulting from
failures arising out of improper installation or operation inconsistent with this
documentation.
This camera is designed to be used indoors.
This camera is not operable outdoors.
Do not expose this camera to direct sunlight for hours and do not install the product near a heater
or an air conditioner. Otherwise, it may cause deformation, discoloration and malfunction. Keep this
camera away from water and moisture.
Do not place this product in the following places:
Locations where it may get wet from rain or water splash
⿟
Locations where a chemical agent is used such as a swimming pool
⿟
Locations subject to humidity, dust, steam and oil smoke
⿟
Locations that have a specific environment that is subject to an inflammable atmosphere or solvents
⿟
Locations where a radiation, an X-ray, a strong radio wave or a strong magnetic field is generated
⿟
Locations where corrosive gas is produced, Locations where it may be damaged by briny air
⿟
such as seashores
Locations where the temperature is not within the specied range (0°to +40°{32°to +104°F}).
⿟
Locations subject to vibrations (This product is not designed for on-vehicle use.)
⿟
Locations subject to condensation as the result of severe changes in temperature
⿟
Be sure to remove this product if it is not in use.
Before installation
When this camera is mounted on a wooden ceiling or a wall, use the wood screws (accessory,
⿟
Screw B). Screws to be used for other materials are not provided. Prepare the screws according
to the material, structure, strength and other factors of the mounting area and the total weight of
objects to be mounted.
Ensure that the mounting surface, anchor and screws are sufciently strong.
⿟
Do not mount this product on a plaster board or a wooden section because they are too weak. If
⿟
this product is unavoidably mounted on such a section, the section shall be sufciently rein-
forced.
Design and engineer the power supply system to turn on/off the power of this
product.
The product has no power switch. When installing the product, use a power supply
device equipped with the ON-OFF switch for servicing.
About the network connection
When connecting to a network using the network cable of this product, observe the following.
When wiring for the network, design and engineer not to be affected by thunder.
Screw tightening
The screws and bolts must be tightened with an appropriate tightening torque according to the
⿟
material and strength of the installation area.
Do not use an impact driver. Use of an impact driver may damage the screws or cause tighten-
⿟
ing excessively.
When a screw is tightened, make the screw at a right angle to the surface. After tightening the
⿟
screws or bolts, perform visual check to ensure tightening is enough and there is no backlash.
Procure xing screws separately.
The screws that secure this product are not supplied. Prepare them according to the material and
strength of the area where the product is to be installed.
Required pull-out capacity of a single screw/bolt is 294 N {66.09 lbf} or more.
Fall prevention measures
When the external safety wire is connected, select a connection point resulting in that nothing will
hit people after the stand is damaged.
Do not remove or loosen the internal camera screws.
Do not loosen the internal camera screws. Otherwise, water exposure may cause damage or mal-
function of camera, or camera dropping may result in injury.
Radio disturbance
When this product is used near TV/radio antenna, strong electric eld or magnetic eld (near a
motor, a transformer or a power line), images may be distorted and noise sound may be produced.
PoE (Power over Ethernet)
Use a PoE hub/device that is compliant with IEEE802.3af standard.
Router
When connecting this product to the Internet, use a broadband router with the port forwarding
function (NAT, IP masquerade). Refer to the Operating Instructions (included in the CD-ROM) for fur-
ther information about the port forwarding function.
Time & date setting
It is necessary to set the time & date before putting this product into operation. Refer to the
Operating Instructions on the provided CD-ROM for descriptions of how to perform the settings.
CPU: Intel® CoreTM 2 Duo 2.4 GHz or faster recommended
Memory: 512 MB or more (A minimum of 1 GB memory is required when using
Microsoft® Windows® 7 or Microsoft® Windows Vista®.)
Network interface: 10BASE-T/100BASE-TX 1 port
Monitor: Image capture size: 1024 x768 pixels or more
Color: 24-bit True color or better
OS: Microsoft® Windows® 7
Microsoft® Windows Vista®
Microsoft® Windows® XP SP3
Web browser: Windows® Internet Explorer® 9.0 (32-bit)
Windows® Internet Explorer® 8.0 (32-bit)
Windows® Internet Explorer® 7.0 (32-bit)
Microsoft® Internet Explorer® 6.0 SP3
Others: CD-ROM drive
(It is necessary to read the operating instructions and use the software on
the provided CD-ROM.)
DirectX® 9.0c or later
Adobe® Reader®
(It is necessary to view PDF le on the provided CD-ROM.)
IMPORTANT
When using a PC that does not meet the above requirements, displaying of images may
⿟
become slower or the web browser may become inoperable.
Microsoft Windows 7 Starter, Microsoft Windows Vista Starter and Microsoft Windows XP
⿟
Professional 64-bit Edition are not supported.
When using IPv6 for communication, use Microsoft Windows7 or Microsoft Windows Vista.
⿟
Note
Refer to “Notes on Windows
⿟®/ Internet Explorer®
versions” (included in the CD-ROM) for fur-
ther information about system requirements for a PC and precautions when using Microsoft
Windows 7, Microsoft Windows Vista or Internet Explorer.
⿟
If using Microsoft Windows XP, screen tearing* may occur when the shooting scene drastically
changes (for example, while shooting fast-moving subjects) due to the GDI restrictions of the OS.
* A phenomenon in which portions of the screen are displayed out of alignment.
For information on the operation verication of the supported operating systems and web
⿟
browsers, refer to our website at http://panasonic.net/pss/security/support/index.html.
System requirements for a PC
Main Unit (1 pc.)
Flexible Stand (1 pc.)
Screw A (1 pc.) Screw B (4 pcs.)
Washer S (1 pc.) Washer L (1 pc.) Safety Wire (1 pc.)
SD Card Cover (1 pc.)
Power cable plug (1 pc.)
−+
Installation Guide (this document) ........ (1 pc.)
Warranty card (P model) ....................... (1 pc.)
CD-ROM*1 ............................................ (1 pc.)
Code label*2 .......................................... (1 pc.)
*1 The CD-ROM contains the operating instructions and different kinds of tool software programs.
*2 This label may be required for network management. The network administrator shall retain the
code label.
Installation Guide
Network Camera
Model No. WV-ST165/WV-ST162
WV-ST165E/WV-ST162E
PGQX1098ZA Cs1011-0
Main functions
● H.264 and JPEG triple encoding
A total of 3 outputs, comprising of 2 H.264 outputs and 1 JPEG output, can be provided.
● Power over Ethernet function
When connecting with a PoE (Power over Ethernet) device, power will be supplied by simply
connecting a LAN cable. (IEEE802.3af compliant)
● Adaptive darkness correction mode
Corrects the blacked-out parts of dark areas of objects that have different illumination intensities.
● Panning/tilting function and preset position function
A single camera provides wide area monitoring.
● Interactive communication with audio
By using the audio output connector and the microphone in connector, receiving audio from the
cameras on a PC and transmitting audio from the PC to the cameras is available.
● SDHC/SD memory card slot equipped
It is possible to save H.264 videos and JPEG images on the SDHC/SD memory card manually at
an alarm occurrence, during the period of the schedule, or on a web browser. It is also possible
to save JPEG images at a network failure occurrence. (Download is possible.)
Adobe, the Adobe logo, and Reader are either registered trademarks or trademarks of Adobe
⿟
Systems Incorporated in the United States and/or other countries.
Microsoft, Windows, Windows Vista, Internet Explorer, ActiveX, and DirectX are either registered
⿟
trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.
⿟
Intel and Intel Core are trademarks or registered trademarks of Intel Corporation in the United
⿟
States and other countries.
iPad, iPhone, and iPod touch are registered trademarks of Apple Inc., registered in the U.S. and
⿟
other countries.
All other trademarks identied herein are the property of their respective owners.
⿟
Trademarks and registered trademarks
Conrm the following items are included in the camera’s packaging.
You will need the following additional items to install and congure the camera.
[Locally procured]
PoE device (When supplying the power using the PoE device)
⿟
a PC (see the system requirements in the Important Information document)
⿟
a router
⿟
a LAN cable (CAT-5 straight cable)
⿟
AC Adaptor (1 pc.)
⿟
* FOR UL LISTED MODEL(S), ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY.
As you will use this unit connected to a network, your attention is called to the following security risks.
A Leakage or theft of information through this unit
B Use of this unit for illegal operations by persons with malicious intent
C Interference with or stoppage of this unit by persons with malicious intent
It is your responsibility to take precautions such as those described below to protect yourself
against the above network security risks.
Use this unit in a network secured by a rewall, etc.
⿟
If this unit is connected to a network that includes PCs, make sure that the system is not infect-
⿟
ed by computer viruses or other malicious entities (using a regularly updated anti-virus program,
anti-spyware program, etc.).
Protect your network against unauthorized access by restricting users to those who log in with
⿟
an authorized user name and password.
Apply measures such as user authentication to protect your network against leakage or theft of
⿟
information, including image data, authentication information (user names and passwords), alarm
mail information, FTP server information and DDNS server information.
After the unit is accessed by the administrator, make sure to close the browser.
⿟
Change the administrator password periodically.
⿟
Do not install the camera in locations where the camera or the cables can be destroyed or dam-
⿟
aged by persons with malicious intent.
Before asking for repairs, check the symptoms with the following table.
Contact your dealer if a problem cannot be solved even after checking and trying the solution in the
table or a problem is not described below.
Symptom Cause/solution
Power is not turned on. u
Are the PoE device and the network cable of the camera
⿟
connected using a LAN cable?
Check whether the connection is appropriately established.
Depending on the PoE device, the power supply will stop
⿟
when the demanded power exceeds its total power limit for
all PoE ports.
Refer to the operating instructions of the PoE device in use.
Distributing, copying, disassembling, reverse compiling and reverse engineering of the software pro-
vided with this product are all expressly prohibited. In addition, exporting any software provided with
this product violating export laws is prohibited.
Precautions
Specications
Limitation of liability
Disclaimer of warranty
Copyright
● Basic
Power source: PoE (IEEE802.3af compliant), 12 V DC
Power consumption:
PoE: 130 mA (Class 2 device), 12 V DC: 430 mA
Ambient operating temperature:
0 °C to +40 °C {32 °F to 104 °F}
Less than 90 % (no condensation)
Ambient operating humidity:
Monitor output:
VBS: 1.0 V [p-p]/75 Ω, composite (BNC), ø3.5 mm mini jack
EXT I/O terminal cable:
ALARM IN 1, ALARM IN 2/ ALARM OUT, ALARM IN 3/ AUX OUT, GND, 12 V DC
Microphone/Line input:
For microphone input
For line input
ø3.5 mm monaural mini jack
Input impedance: Approx. 2.2 kΩ
Applicable microphone: Plug-in power type
Supply voltage: 3.3 V ±0.5 V
Input level: Approx. –10 dBV
Audio output: ø3.5 mm stereo mini jack (monaural output)
Output impedance: Approx. 560 Ω
Line level
Dimensions: 100 mm (W) x 100 mm (H) x 74 mm (D) {3-47/50 inches (W) x 3-47/50
inches (H) x 2-23/25 inches (D)} (excluding projection)
Mass: Main body: 345 g {0.76 lbs}
Finish: Main body : PC/ABS resin, sail white
Dome section: Clear polycarbonate resin
● Camera
Image sensor: 1/4 type MOS image sensor
Effective pixels: Approx. 1.3 megapixels
Scanning area: 3.52 mm (H) × 2.64 mm (V) {7/50 inches (H) × 1/10 inches (V)}
Scanning system: Progressive
Minimum illumination: Color: 0.6 lx {0.06 footcandle}
(F2.2, Auto slow shutter: Off (1/30 s), Gain: On (High))
0.038 lx {0.0038 footcandle}
(F2.2, Auto slow shutter: max. 16/30 s, Gain: On (High))*
BW: 0.5 lx {0.05 footcandle}
(F2.2, Auto slow shutter: Off (1/30 s), Gain: On (High))
0.031 lx {0.0031 footcandle}
(F2.2, Auto slow shutter: max. 16/30 s, Gain: On (High))*
* Converted value
Wide dynamic range: On/Off
Face WDR: On/Off
Gain (AGC): On (Low)/ On (Mid)/ On (High)/ Off
Adaptive black stretch: On/Off
Light control mode setting:
Indoor scene (50Hz/60Hz)/ELC
ELC
(Maximum exposure time):
ELC(1/30 s), ELC(3/100 s), ELC(3/120 s), ELC(2/100 s), ELC(2/120 s),
ELC(1/100 s), ELC(1/120 s), ELC(1/250 s), ELC(1/500 s),
ELC(1/1000 s), ELC(1/2000 s), ELC(1/4000 s), ELC(1/10000 s)
Auto slow shutter: Off (1/30 s), Max. 2/30s, Max. 4/30s, Max. 6/30s, Max. 10/30s,
Max. 16/30s
Day & Night (electrical): Off/Auto
White balance: ATW1/ ATW2/ AWC
Digital noise reduction: High/Low
Video analytics
Face detection:
On/Off (with the XML notication setting)
Privacy zone: On/Off (up to 2 zones available)
Camera title on screen:
Up to 20 characters (alphanumeric characters, marks), On/Off
Video motion detection
(VMD alarm):
On/Off, (available at each preset)
● Lens
Zoom ratio: Extra zoom: 2x (under VGA resolution)
Digital (electronic) zoom:
8x (Max 16x combined with Extra Optical Zoom under VGA)
Focal length: 1.95 mm
Maximum aperture ratio:
1: 2.2
Focus range: ∞ - 0.5 m
Angular eld of view: Horizontal: 85°, Vertical: 68°
● Panning/tilting platform
Panning range: -47.5°- +47.5°
Panning speed:
Manual: Approx. 5 °/s - 80 °/s, Preset: Up to approx. 80 °/s
Tilting range: -45° to +10°
Tilting speed:
Manual: Approx. 5 °/s - 80 °/s, Preset: Up to approx. 80 °/s
Number of the preset positions:
64
Map shot: Preset map-shot
Self return:
10 s/ 20 s/ 30 s/ 1 min/ 2 min/ 3 min/ 5 min/ 10 min/ 20 min/ 30 min/ 60 min
Network security
WARNING
CAUTION
Turn the power off when cleaning this product.
• Failure to observe this may cause injury.
Refer installation work to the dealer.
• Installation work requires technique and experiences. Failure to observe this may cause re,
electric shock, injury, or damage to the product.
Be sure to consult the dealer.•
Stop the operation immediately when something is wrong with this product.
• When smoke goes up from the product, the smell of smoke comes from the product, or the
exterior of the product has deteriorated, continued use will cause a re or fall of the product
resulting in injury, or damage to the product.
Turn the power off immediately and contact qualied service personnel for service.•
Select an installation area that can support the total weight.
•
Selecting an inappropriate installation surface may cause this product to fall down or topple
over, resulting in injury.
Installation work shall be started after sufcient reinforcement.•
Periodic inspections shall be conducted.
• Rust on the metal parts or screws may cause a fall of the product resulting in injury or accidents.
Consult the dealer for the inspections.•
The screws and bolts must be tightened to the specied torque.
• Failure to observe this may cause a drop resulting in injury or accidents.
Do not install this product in locations subject to vibration.
• Loosening of mounting screws or bolts may cause a fall of the product resulting in injury.
The measures of protection against a fall of this product shall be taken.
•
Failure to observe this may cause a drop resulting in injury or accidents. Be sure to install the safety wire.
Install this product in a location high enough to avoid people and objects from
•
bumping the product.
Failure to observe this may cause a drop resulting in injury or accidents.
Turn the power off when do wiring of this product.
•
Failure to observe this may cause electric shock. In addition, short circuit or wrong wiring may
cause re.
Do not attempt to disassemble or modify this product.
• Failure to observe this may cause re or electric shock. Consult the dealer for the repair or
inspections.
Do not insert any foreign objects.
• This could permanently damage this product. Turn the power off immediately and contact
qualied service personnel for service.
Do not use this product in an inammable atmosphere.
• Failure to observe this may cause an explosion resulting in injury.
Avoid installing this product in the locations where salt damage occurs or
•
corrosive gas is produced.
Otherwise, the mounting portions will deteriorate and accidents such as a fall of the product may occur.
Do not strike or give a strong shock to this product.
• Failure to observe this may cause re or injury.
Do not rub the edges of metal parts with your hand.
• Failure to observe this may cause injury.
Do not touch this product or the connected cables during thunder. (even in the
•
process of work)
Failure to observe this may cause electric shock.
Keep SDHC/SD memory cards (option) away from infants and children.
• Otherwise, they may swallow the cards by mistake.
In this case, consult a doctor immediately.•
● Network
Network: 10BASE-T/100BASE-TX, RJ45 connector
Resolution: WV-ST165
Imaging mode: 4:3
H.264 1280x960/ VGA (640x480)/ QVGA (320x240) max.30fps
JPEG 1280x960/ VGA (640x480)/ QVGA (320x240) max.30 fps
Imaging mode: 16:9
H.264 1280x720/ 640x360/ 320x180 max.30 fps
JPEG 1280x720/ 640x360/ 320x180 max.30 fps
WV-ST162
Aspect ratio: 4:3
H.264 SVGA(800x600)/ VGA(640x480)/ QVGA(320x240) max. 30 fps
JPEG SVGA(800x600)/ VGA(640x480)/ QVGA(320x240) max. 30 fps
Aspect ratio: 16:9
H.264 640x360/ 320x180, max. 30 fps
JPEG 640x360/ 320x180, max. 30 fps
Image compression
method:
*1
H.264
I
mage quality: Low/ Normal/ Fine
Transmission type: Unicast/Multicast
Bit rate:
Constant bit rate/ Best effort:
64 kbps/ 128 kbps/ 256 kbps/ 384 kbps/ 512 kbps/
768 kbps/ 1024 kbps/ 1536 kbps/ 2048 kbps/ 3072 kbps/
4096 kbps/ 8192 kbps
Frame rate:
1 fps/ 3 fps/ 5 fps/ 7.5 fps/ 10 fps/ 12 fps/ 15 fps/ 20 fps/
30 fps
JPEG Image quality: 0 SUPER FINE/ 1 FINE/ 2/ 3/ 4/ 5 NORMAL/
6/ 7/ 8/ 9 LOW (10 steps: 0-9)
Transmission type: PULL/PUSH
Transmission interval: 0.1 fps - 30 fps (JPEG frame rate will be restricted when displaying
both JPEG and H.264/ images.)
Audio compression
method:
G.726 (ADPCM) 32 kbps/ 16 kbps
G.711 64 kbps
Bandwidth control: Unlimited/ 64 kbps/ 128 kbps/ 256 kbps/ 384 kbps/ 512 kbps/
768 kbps/ 1024 kbps/ 2048 kbps/ 4096 kbps/ 8192 kbps
Protocol: IPv6: TCP/IP, UDP/IP, HTTP, HTTPS, RTP, FTP, SMTP, DNS, NTP,
SNMP, DHCPv6, MLD, ICMP, ARP
IPv4: TCP/IP, UDP/IP, HTTP, HTTPS, RTSP, RTP, RTP/RTCP, FTP, SMTP,
DHCP, DNS, DDNS, NTP, SNMP, UPnP, IGMP, ICMP, ARP
Maximum concurrent
access number:
14 (Depends on network conditions)
FTP client: Alarm image transmission, FTP periodic transmission
Multi-screen: Up to 16 camera images can be displayed simultaneously on a multi-
screen. (Including the camera itself)
Compatible SDHC/
SD memory card (option):
Manufactured by Panasonic
SDHC memory card: 4 GB, 8 GB, 16 GB, 32 GB
SD memory card: 256 MB, 512 MB, 1 GB, 2 GB
(except miniSD card and microSD card)
Cellular phone
compatibility:
JPEG image, panning/tilting/zoom control, AUX control (by access
level)
Mobile terminal compatibility:
iPad, iPhone, iPod touch (iOS 4.2.1 or later) (As of August, 2011)
*1 Transmission for 2 streams can be individually set in the same compression method.
● Optional accessories
User License Accessory (For H.264) BB-HCA8A (P model)
BB-HCA8CE (E model, Korea*) * Required in Korea
Troubleshooting
Important safety instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other appara-
tus (including ampliers) that produce heat.
9) Only use attachments/accessories specied by the manufacturer.
10) Use only with the cart, stand, tripod, bracket, or table specied by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury
from tip-over.
S3125A
11) Unplug this apparatus during lightning storms or when unused for long periods of time.
12) Refer all servicing to qualied service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
THIS PUBLICATION IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF
THE THIRD PARTY’S RIGHT.
THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL
ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE
IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).
IN NO EVENT SHALL Panasonic System Networks Co., Ltd. BE LIABLE TO ANY PARTY OR ANY
PERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT,
FOR THE CASES, INCLUDING BUT NOT LIMITED TO BELOW:
(1) ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT, SPECIAL,
CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE PRODUCT;
(2) PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENT
OPERATION OF THE USER;
(3) ALL MALFUNCTIONS OR TROUBLES FROM UNAUTHORIZED DISASSEMBLE, REPAIR OR
MODIFICATION OF THE PRODUCT BY THE USER, REGARDLESS OF THE CAUSE OF THE
MALFUNCTION OR TROUBLE;
(4) INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED, DUE TO
ANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;
(5) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISING
OUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY;
(6) ANY CLAIM OR ACTION FOR DAMAGES, BROUGHT BY ANY PERSON OR ORGANIZATION
BEING A PHOTOGENIC SUBJECT, DUE TO VIOLATION OF PRIVACY WITH THE RESULT OF
THAT SURVEILLANCE-CAMERA’S PICTURE, INCLUDING SAVED DATA, FOR SOME
REASON, BECOMES PUBLIC OR IS USED FOR ANY PURPOSE;
(7) LOSS OF REGISTERED DATA CAUSED BY ANY FAILURE.
For U.S. and Canada:
Panasonic System Networks Company of America,
Unit of Panasonic Corporation of North America
www.panasonic.com/business/
For customer support, call 1.800.528.6747
Three Panasonic Way, Secaucus, New Jersey 07094 U.S.A.
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada
(905)624-5010
www.panasonic.ca
© Panasonic System Networks Co., Ltd. 2011
For Europe and other countries:
http://panasonic.net
Importer’s name and address to follow EU rules:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg F.R.Germany
WARNING:
To prevent fire or electric shock hazard, do not expose this apparatus to rain or moisture.
⿟
To prevent injury, this apparatus must be securely attached to the floor/wall/ceiling in accor-
⿟
dance with the installation instructions.
The installation shall be carried out in accordance with all applicable installation rules.
⿟
The connections should comply with local electrical code.
⿟
For U.S.A
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material - spe-
cial handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate/
For U.S. and Canada: WV-ST165/WV-ST162
For Europe and other countries: WV-ST165E/WV-ST162E
UL listed model No. WV-ST165/WV-ST162
For Canada
This Class A digital apparatus complies with Canadian ICES-003.
For U.S.A
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
FCC Caution: To assure continued compliance, (example - use only shielded interface cables
when connecting to computer or peripheral devices). Any changes or modications not express-
ly approved by the party responsible for compliance could void the user’s authority to operate
this equipment.
For U.S.A
The model number and serial number of this product may be found on the surface of the unit.
You should note the model number and serial number of this unit in the space provided and
retain this book as a permanent record of your purchase to aid identication in the event of theft.
Model No. _________________________________
Serial No. __________________________________
For Europe
We declare under our sole responsibility that the product to which this declaration relates is in
conformity with the standard or other normative document following the provisions of Directive
2004/108/EC.
Wir erklären in alleiniger Verantwortung, daß das Produkt, auf das sich diese Erklärung bezieht,
mit der folgenden Norm oder normativen Dokument übereinstimmt. Gemäß den Bestimmungen
der Richtlinie 2004/108/EC.
Nous déclarons sous notre propre responsabilité que le produit auquel se réfère la présente
déclaration est conforme á la norme spéciée ou à tout autre document normatif conformément
aux dispositions de la directive 2004/108/CE.
Nosotros declaramos bajo nuestra única responsabilidad que el producto a que hace referencia
esta declaración está conforme con la norma u otro documento normativo siguiendo las estipu-
laciones de la directiva 2004/108/CE.
Noi dichiariamo sotto nostra esclusiva responsabilità che il prodotto a cui si riferisce la presente
dichiarazione risulta conforme al seguente standard o altro documento normativo conforme alle
disposizioni della direttiva 2004/108/CE.
Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft,
voldoet aan de volgende norm of ander normatief dokument, overeenkomstig de bepalingen van
Richtlijn 2004/108/EC.
Vi erklærer os eneansvarlige for, at dette produkt, som denne deklaration omhandler, er i over-
ensstemmelse med standard eller andre normative dokumenter i følgebestemmelserne i direktiv
2004/108/EC.
Vi deklarerar härmed vårt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i
överensstämmelse med standarddokument eller annat normativt dokument som framställs i
direktiv 2004/108/EC.
Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus koskee, noudattaa
seuraavaa standardia tai muuta ohjeellista asiakirjaa, jotka noudattavat direktiivin 2004/108/EC
säädöksiä.
Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen gjelder for, er i overens-
stemmelse med følgende norm eller andre normgivende dokumenter som følger bestemmelsene
i direktiv 2004/108/EC.
Information for Users on Collection and Disposal of Old Equipment and used Batteries
These symbols on the products, packaging, and/or accompanying documents mean
that used electrical and electronic products and batteries should not be mixed with
general household waste.
For proper treatment, recovery and recycling of old products and used batteries,
please take them to applicable collection points, in accordance with your national leg-
islation and the Directives 2002/96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and the envi-
ronment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries,
please contact your local municipality, your waste disposal service or the point of sale
where you purchased the items.
Penalties may be applicable for incorrect disposal of this waste, in accordance with
national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer
or supplier for further information.
Cd
[Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to discard these
items, please contact your local authorities or dealer and ask for the correct method
of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it
complies with the requirement set by the Directive for the chemical involved.
About the user manuals
There are 2 sets of operating instructions for the WV-ST165, WV-ST162 (P model), WV-ST165E,
WV-ST162E (E model) as follows.
Installation Guide: Explains how to install and connect devices, as well as how to connect and
⿟
congure the network.
Operating Instructions (included in the CD-ROM): Explains how to perform the settings and how
⿟
to operate this camera.
Adobe® Reader® is required to read these operating instructions on the provided CD-ROM.
When the Adobe® Reader® is not installed on the PC, download the latest Adobe Reader from the
Adobe web site and install it.
“WV-ST165, WV-ST162” or “ST165, ST162” shown in the instructions and illustrations used in
these operating instructions indicates the WV-ST165, WV-ST162, WV-ST165E, WV-ST162E.
The screens used in these operating instructions show the cases of P models.
MIC POWER
To the power supply
LAN cable
PoE indicator
LINK indicator
To the hub or
the router
Indicator
When connecting the camera using PoE (Power over
Ethernet)
When connecting the camera using 12 V DC power supply
Caution:
FOR UL LISTED MODEL(S), ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY.
⿟
1 Loosen the screw of the power cord plug (accessory).
2 Connect the cable of the 12 V DC power supply* to the power cord plug.
Strip 3 mm to 7 mm {1/8 inches to 9/32 inches} from the end of the wire, and twist the
stripped part of the wire sufciently to avoid short circuit.
Specication of cable (wire): 16 AWG - 24 AWG, Single core, twisted
Check whether the stripped part of the wire is not exposed and is securely connected.
⿟
3 Tighten the screw of the power cord plug.
4 Connect the power cord plug to the 12 V DC power supply terminal on the rear of the cam-
era.
IMPORTANT
Be sure to use the power cord plug provided
⿟
with this product.
⿟Be sure to fully insert the power cord plug
into the 12 V DC power supply terminal.
Otherwise, it may damage the camera or
cause malfunction.
¢ Installing the camera on the ceiling or wall
Make sure the flexible stand is firmly mounted on a beam of wood (25 mm [1 inch] and
greater) etc. When there is no beam, apply a board on the other side of the ceiling or wall
to make sure the camera does not drop.
When mounting on a mortar or concrete surface
Prepare anchors for 4 mm (3/16 inch) diameter screws for mounting.
Mortar ceilings or walls break easily when drilling. Be careful of pieces
of mortar which may become loose and fall.
1.
Place the exible stand on the ceiling or wall where you plan to mount the
exible stand and mark the points where you are going to make holes.
2. Make holes with an electric drill. Insert anchors (locally procured)
into the holes and push them inside the holes with a hammer.
3. Mount the exible stand using the screws.
Drill for concrete (in case of tile,
use a drill for tile) Perform waterproof treatment
(caulking)
Determining the mounting position Determining the length of the cable
Determining how to wire the cable
Determining how to mount the camera
It is necessary to make a hole in the ceiling or wall to pass the cables
through. Make a hole 25 mm {31/32"} in diameter.
¢ Tripod Mount
It is also possible to mount the camera on a standard tripod stand (locally
procured).
Conrm the distance from the camera's
installation position to the computer and
then prepare the necessary length of LAN
cable (locally procured).
Hole for cables
ø
25 mm (
ø
1 inch)
IMPORTANT
⿟Do not connect 2 wires or more directly to a terminal. When it is necessary to connect 2
or more wires, use a splitter.
⿟Input and output of the external I/O terminal 2 and 3 can be switched by configuring the
setting. The default of EXT I/O terminal 2 is "ALARM IN 2" and of EXT I/O terminal 3 is
"ALARM IN 3". It is possible to determine whether or not to receive input from EXT I/O
terminal 2 and 3 (ALARM IN2, 3) by selecting "Off", "Alarm input", "Alarm output" or "AUX
output" for "Terminal alarm 2" or "Terminal alarm 3" on the [Alarm] tab on the "Alarm setup"
page. Refer to the Operating Instructions (included in the CD-ROM) for further information.
⿟The default of EXT I/O terminals is "Off". When "Off" is selected, it is possible to connect
external devices as well as the input setting.
⿟When using the EXT I/O terminals as the output terminals, ensure they do not cause
signal collision with external signals.
<Ratings>
ALARM IN1, ALARM IN2, ALARM IN3
⿟
Input specication : No-voltage make contact input (4 V - 5 V DC, internally pulled up)
OFF : Open or 4 V - 5 V DC
ON : Make contact with GND (required drive current: 1 mA or more)
ALARM OUT, AUX OUT
⿟
Output specication : Open collector output (maximum applied voltage: 20 V DC)
Open : 4 V - 5 V DC by internal pull-up
Close : Output voltage 1 V DC or less (maximum drive current: 50 mA)
Microphone/line input connector · Audio output terminal
You can connect an external microphone and external speaker to the camera to use the Listen and Talk
features, respectively. The microphone cable should be no longer than 7 m (23 feet). If you use an external
microphone, excessive cable length or a poor quality cable can cause degradation in audio quality.
Monitor out connector for adjustment
Connect a monaural mini plug (ø3.5 mm) (only for checking if images are displayed on the monitor).
Recommended plug: L type
⿟
IMPORTANT
The monitor out connector for adjustment is provided only for checking the adjustment of
⿟
the angular eld of view on the video monitor when installing the camera or when servic-
ing. It is not provided for recording/monitoring use.
Black bands may appear at the top and bottom or right and left of the screen. (That does
⿟
not affect the adjustment because the angular eld of view is not changed.)
Insert a SD memory card
1 Open the cover on the side of the camera.
2
Insert the SD memory card with the label facing the rear of the camera and the pins
facing the front of the camera. Gently push the card with your nger until it clicks.
Note
If the camera’s indicator turns red, remove the SD
⿟
memory card and conrm that the card is not write-
protected. If the indicator is still red, the card must be
formatted before it can be used.
3 Close the cover.
IMPORTANT
Do not mount this product on
a plaster board or a wooden
section because they are too
weak. If this product is
unavoidably mounted on such
a section, the section
shall be sufciently reinforced
.
IMPORTANT
Do not install this by
products that
generates a strong
radio wave or a strong
magnetic eld.
IMPORTANT
Do not install on
locations subject to
humidity and oil
smoke.
IMPORTANT
Do not install near the
strong light source. IMPORTANT
Do not install near
any heat sources.
IMPORTANT
Do not install this on
locations subject to
vibrations.
Note
If the indicator does not turn green, see “Troubleshooting” in the Operating Instructions
⿟
on the provided CD-ROM.
Refer to the operating instructions of the product in use about the operations of the PoE
⿟
device.
IMPORTANT
Use a 4-pair UTP/STP cable.
⿟
Make sure that the PoE device in use is compliant with IEEE802.3af standard.
⿟
For information on recommended PoE devices, refer to our website at
⿟
(http://panasonic.net/pss/security/support/ info.html).
1 Check the installing place
<Front view>
<Side and bottom view>
<Rear view>
Lens cover
Lens
Microphone
Indicator
INITIAL SET button
SD memory card slot
FUNCTION button
(lit when recording)
Stand/tripod mounting hole
Stand mounting hole
12 V DC power supply terminal/
Monitor out connector for adjustment/
External I/O terminals cable hook
LAN port [10BASE-T/100BASE-TX]
Audio output terminal/Microphone/
line input connector cable hook
Microphone/line input connector
[MIC/LINE IN]
Audio output terminal [AUDIO OUT]
Monitor out connector for adjustment
[MONITOR OUT]
External I/O terminals [EXT I/O]
12 V DC power supply terminal [POWER]
External I/O terminals
Pin Function
6 DC power output
Power output voltage 10.5 V ~ 13 V
Power output current 100 mA
5 GND
4 GND
3 EXT I/O terminal 3 (ALARM IN 3/ AUX OUT)
2 EXT I/O terminal 2 (ALARM IN 2/ ALARM OUT)
1 EXT I/O terminal 1 (ALARM IN 1)
About the [INITIAL SET] button
After turning off the power of the camera, turn on the power of the camera while holding down this
button, and wait for around 5 seconds or more without releasing this button. Wait around 3 minute
after releasing the button. The camera will start up and the settings including the network settings
will be initialized. Before initializing the settings, it is recommended to write down the settings in
advance. The initialization will be complete when the live indicator stops blinking orange and lights
off. Note that the preset position settings and the CRT key (SSL encryption key) used for the
HTTPS protocol will not be initialized.
IMPORTANT
Do not turn off the power of the camera during the process of initialization. Otherwise,
⿟
it may fail to initialize and may cause malfunction.
About the [RESTART] button
When the camera is on, you can also restart the camera by pressing the RESTART button. Press
and hold the RESTART button for about one second with a pointed object. Restarting is completed
when the camera's pan/tilt performs its initial movement.
an external microphone/ line input
an external powered speaker
( 3.5 mm mini plug)ø
( 3.5 mm stereo mini plug)ø
cable 2 ±0.3ø
(Output impedance 560 Ω line level)
(Plug-in power 3.3 ±0.5 V) GND
GND
unconnected
signal
signal
3 Connections
2 Major operating controls
−+
＋
−
Strip range
Approx. 3 mm - 7 mm
{1/8 inches - 9/32 inches}
Power cable plug
(accessory)
MIC POWER
INITIAL SETRESTART
FUNCTION
RESTART button
EXT I/O
POWER
- +
12V = IN
654321
10BASE-T/
100BASE-TX
Beam of wood
At least 25 mm (1 inch)
External I/O terminals
Connect external devices to the EXT I/O terminal.
When connecting an external device, remove 9 mm - 10 mm
{11/32 inches - 13/32 inches} of the outer jacket of the cable
and twist the cable core to prevent the short circuit rst.
Specication of cable (wire): 22 AWG - 28 AWG
⿟
Single core, twisted
Strip range
Approx. 9 mm - 10 mm
{11/32 inches - 13/32 inches}
For audio output terminal
For microphone/ line input terminal
To microphone
To speaker input terminal
Adjust the camera to a suitable position/direction while conrming the images actually displayed
on the computer screen.
Wiring without making a hole for a cable in the ceiling or wall
1 Place the exible stand (accessory) on
the ceiling or wall, and determine the
mounting position of the stand.
Make sure the flexible stand is firmly mounted on a
beam of wood (25 mm [1 inch] and greater) etc. When
there is no beam, apply a board on the other side of the
ceiling or wall to make sure the camera does not drop.
2
Secure the safety wire (accessory) to
the camera using screw A (accessory)
and washer S (accessory)
.
3 Remove the tab on the exible stand.
4
Pass the cables through the notch.
When there are many cables to pass through the
notch, pass through the larger cables rst.
IMPORTANT
If the cables cannot be passed through the notch, wrap the cables to the stand shaft using
tape (locally procured) or other materials.
5 Mounting the Camera
Configuring the camera so that it can be accessed from a PC
If you are using firewall software on your PC, the Setup Program may not be able to find any cam-
eras on your network. Configure the setting of the camera after temporarily invalidating the firewall
software.
1 Insert the provided CD-ROM into the CD-ROM drive of your PC
The License Agreement will be displayed. Read the Agreement and choose "I
⿟
accept the term in the license agree-ment", and click [OK].
The launcher window will be displayed.
⿟
If the launcher window is not displayed, double click the "CDLauncher.exe" le on
the CD-ROM.
Note
⿟Refer to "About the CD-ROM" in the Operating Instructions on the provided
CD-ROM for further information about CDLauncher.
Remove a SD memory card
1 Close the slide cover on the side of the camera.
2 Press the FUNCTION button.
When the FUNCTION button is pressed,
recording stops and the green light turns
off. Conrm that the FUNCTION button
green light has turned off before
proceeding to step 3.
3 Push the card slightly to eject it, then remove the card.
4 Close the cover.
Note
To suit the area in which you will install the camera, you can attach the provided SD Card
Cover (Hard type), in order to help prevent SD card theft.
Not all forms of theft can be prevented.
⿟
IMPORTANT
⿟
Make sure that SD memory card recording has stopped and that the card is not being accessed
before removing the card. (The FUNCTION button will light while images are being recorded to the
card.) We recommend pressing the FUNCTION button to stop SD memory card recording before
ejecting the card.
If the SD memory card is removed while it is being recorded to or accessed, the card
⿟
may become unreadable and may need to be formatted (i.e., erased) again before
use.
FUNCTION button
5 Mount the exible stand rmly to the ceiling or wall with screw B
(accessory).
When mounting the flexible stand to the wall, position the flexible stand so that the "p"
marker is facing upward.
6 Attach the camera by screwing the threaded mount into the stand
mounting hole.
Beam of wood
At least 25 mm
(1 inch)
7 Pass the cables through the connector cover, and then connect all
necessary cables (AC adaptor, LAN, audio/video, etc.). Refer to
"Connections".
IMPORTANT
When installing the camera, hook the cord of the AC adaptor (locally procured) and the
cables for the external speaker/external sensor/mic/video, etc. around the hooks when mak-
ing connections.
8 Adjust the camera position and tighten the exible stand grip and
the tightening screw rmly.
The xing position of the tightening screw can be adjusted according to
the direction the camera is facing and its angle.
9 Adjust the length of the safety wire when it is taut, and secure it to
the ceiling or wall using screw B (accessory) and washer L
(accessory).
Attach the safety wire in a position so that if the camera were to become detached, it
would not fall on nearby people.
Wiring through a hole made in the ceiling or wall
Make a hole for cables in the ceiling or wall. Secure the safety wire to the camera and pass the
cables through the notch. Then follow steps 2, 4 to 9.
It is not necessary to remove the tab on the exible stand.
Screw A
(accessory)
Washer S
(accessory)
Safety wire
(accessory)
At least 165 mm
Screw B
Screw B
(accessory)
¢ ¢Ceiling Wall
¢ ¢Ceiling Wall
Grip
Stand mounting hole
Threaded mount
Indicator
Stand/tripod
mounting hole
Grip
* It is possible to attach the stand to the
stand mounting hole, the rear of the
camera.
Audio output terminal/
Microphone/line input
connector cable hook
12 V DC power
supply terminal/
Monitor out connector
for adjustment/
External I/O terminals
cable hook
Screw B
Screw B
¢ ¢Ceiling Wall
Washer L (accessory)
Washer L (accessory)
Screw B
Screw B
¢Ceiling ¢Wall
Hole for cables
ø
25 mm (
ø
1 inch)
Hole for cables
ø
25 mm (
ø
1 inch)
4 Congurethesettingsofthecamera
SD Card Cover
(Hard type)
SD Card Cover
(Soft type)
the tab on the
exible stand
¢ ¢Ceiling Wall
Grip
Tightening screw
Tightening screw
Grip
p
p
Keep a distance of 165 mm
{0.54 feet} or more from a ceiling
Otherwise the camera
cannot be mounted
properly.
2 Click the [Run] button next to [IP Setting Software]
"Panasonic IP Setting Software" page will be displayed. Click the [Network Settings] button
after selecting the MAC address/IP address of the camera to be congured.
3 Select the camera you want to congure, and click [Access Camera].
Note
When cameras are displayed in [IP Setting Software] screen, click the cam-
⿟
era with same MAC address as the MAC address printed on the camera
that you want to congure.
Threaded mount
4 When the [Access Camera] button is clicked, live images of the
selected camera will be displayed.
Note
When no image is displayed on the “Live” page, refer to “Troubleshooting” in the Operating
⿟
Instructions on the provided CD-ROM.
It is possible to enhance the network security by encrypting the access to cameras using
⿟
the HTTPS function. Refer to “Access the camera using the HTTPS protocol” in the
Operating instructions on the provided CD-ROM.
Click the [Setup] button on the “Live” page, the user authentication window will be dis-
⿟
played. Enter the default user name and password as follows, and log in.
User name: admin
Password: 12345

Produktspezifikationen

Marke: Panasonic
Kategorie: Überwachungskamera
Modell: WVST165

Brauchst du Hilfe?

Wenn Sie Hilfe mit Panasonic WVST165 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Überwachungskamera Panasonic

Panasonic

Panasonic WV-SFN480 Bedienungsanleitung

2 Oktober 2024
Panasonic

Panasonic AW-HN130 Bedienungsanleitung

10 September 2024
Panasonic

Panasonic WV-CP630/G Bedienungsanleitung

9 September 2024
Panasonic

Panasonic AW-UE100K Bedienungsanleitung

28 August 2024
Panasonic

Panasonic AW-UR100 Bedienungsanleitung

20 August 2024
Panasonic

Panasonic WV-U2540L Bedienungsanleitung

3 August 2024
Panasonic

Panasonic WV-SF438E Bedienungsanleitung

1 August 2024
Panasonic

Panasonic AW-HN40H Bedienungsanleitung

29 Juli 2024
Panasonic

Panasonic AW-UE150WE Bedienungsanleitung

25 Juli 2024
Panasonic

Panasonic AW-UE50 Bedienungsanleitung

24 Juli 2024

Bedienungsanleitung Überwachungskamera

Neueste Bedienungsanleitung für -Kategorien-

Trebs

Trebs CCD-401C Bedienungsanleitung

15 Oktober 2024
D-Link

D-Link DCS-7510 Bedienungsanleitung

15 Oktober 2024
Foscam

Foscam FI9900EP Bedienungsanleitung

14 Oktober 2024
Alecto

Alecto DVC-215IP Bedienungsanleitung

14 Oktober 2024
Hikvision

Hikvision DS-2CD2326G2-IU Bedienungsanleitung

13 Oktober 2024
Hikvision

Hikvision DS-2TD2166-15/V1 Bedienungsanleitung

13 Oktober 2024
Hikvision

Hikvision DS-2DE7A245IX-AE/S1 Bedienungsanleitung

13 Oktober 2024
Hikvision

Hikvision DS-2CD7A26G0-IZ(H)SY Bedienungsanleitung

11 Oktober 2024
Hikvision

Hikvision DS-2CE79DF8T-AZE Bedienungsanleitung

11 Oktober 2024
Hikvision

Hikvision DS-2XM6726G0-I(D)(S)(M)(/ND) Bedienungsanleitung

11 Oktober 2024