Panasonic WV-S6130 Bedienungsanleitung

Panasonic Überwachungskamera WV-S6130

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Panasonic WV-S6130 (4 Seiten) in der Kategorie Überwachungskamera. Dieser Bedienungsanleitung war für 3 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

This Installation Guide explains the above Ⓐ “Installing the camera to a ceiling

that has adequate structural strength”. When you use mount brackets (optional

accessory), read their operating instructions.

【1】Process the installation surface.

Decide the attachment position and bore

holes for screws or anchors on the ceiling

and a hole for wiring (ø25 mm {31/32

inches}: See the lower-right illustration) as

occasion demands.

◆ If fixed with M4 screws

Fixed dimension:

83.5 mm × 46 mm

{3-9/32 inches × 1-13/16 inches}

◆ If fixed with M6 screws

Fixed dimension:

110 mm × 64 mm

{4-5/16 inches × 2-17/32 inches}

Note:

•

The center point of the cam-

era mount bracket (accessory)

should be more than 100 mm

{3-15/16 inches} away from

obstacles such as a wall.

• The camera mount bracket

(accessory) should be

installed with its “⇧FRONT”

mark in the Panasonic logo

direction (shooting direction)

after installation.

【2】

Attach the camera mount

bracket using 4 fixing screws

(M4 or M6: locally procured).

Minimum pull-out strength: 196 N {44 lbf} (per 1 pc.)

FRONT

OPEN

LOCK

Network Camera

Model No. WV-S6130

Installation Guide

Included Installation Instructions

Important safety instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9) Only use attachments/accessories specified by the manufacturer.

10) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury

from tip-over.

S3125A

11) Unplug this apparatus during lightning storms or when unused for long periods of time.

12) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been dam-

aged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally,

or has been dropped.

Troubleshooting

Open Source Software

• This product contains open source software licensed under GPL (GNU General Public License),

LGPL (GNU Lesser General Public License), etc.

• Customers can duplicate, distribute and modify the source code of the software under license of

GPL and/or LGPL.

• Refer to the “readme.txt” file on the provided CD-ROM for further information about open source

software licenses and the source code.

• Please note that Panasonic shall not respond to any inquiries regarding the contents of the source

code.

The model number and serial number of this

product may be found on the surface of the unit.

You should note the model number and serial

number of this unit in the space provided and

retain this book as a permanent record of your

purchase to aid identification in the event of

theft.

Model No.

Serial No.

NOTE: This equipment has been tested and found

to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference when the

equipment is operated in a commercial environ-

ment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed

and used in accordance with the instruction man-

ual, may cause harmful interference to radio com-

munications.

Operation of this equipment in a residential area is

likely to cause harmful interference in which case

the user will be required to correct the interfer-

ence at his own expense.

FCC Caution: To assure continued compliance,

(example - use only shielded interface cables

when connecting to computer or peripheral devic-

es). Any changes or modifications not expressly

approved by the party responsible for compliance

could void the user’s authority to operate this

equipment.

For U.S.A.

CAN ICES-3(A)/NMB-3(A)

For Canada

WARNING:

• To prevent injury, this apparatus must be secure-

ly attached to the wall/ceiling in accordance with

the installation instructions.

• To prevent fire or electric shock hazard, do not

expose this apparatus to rain or moisture.

• The apparatus should not be exposed to drip-

ping or splashing.

• All work related to the installation of this product

should be made by qualified service personnel

or system installers.

• The installation shall be carried out in accor-

dance with all applicable installation rules.

• The connections should comply with local elec-

trical code.

• Batteries (battery pack or batteries installed)

shall not be exposed to excessive heat such as

sunlight, fire or the like.

CAUTION:

• Any changes or modifications not expressly

approved by the party responsible for compli-

ance could void the user’s authority to operate

the equipment.

• The network camera is only intended for a con-

nection to an ethernet or PoE network without

routing to the outside plant.

Disposal of Old Equipment and Batteries

Only for European Union and countries with recycling systems

These symbols on the products, packaging, and/or accompanying documents mean that used

electrical and electronic products and batteries must not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them

to applicable collection points in accordance with your national legislation.

By disposing of them correctly, you will help to save valuable resources and prevent any potential

negative effects on human health and the environment.

For more information about collection and recycling, please contact your local municipality.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national

legislation.

Note for the battery symbol (bottom symbol)

This symbol might be used in combination with a chemical symbol. In this case it complies with the

requirement set by the Directive for the chemical involved.

About the user manuals

Product documentation is composed of the following documents.

• Installation Guide (this document):

Explains installation, cable connections, mounting and removal.

• Important Information (included in the CD-ROM):

Provides basic information about the product.

• Operating Instructions (included in the CD-ROM): Explains how to perform the settings and how to oper-

ate this camera.

Adobe® Reader® is required to read these operating instructions on the provided CD-ROM.

When the Adobe Reader is not installed on the PC, download the latest Adobe Reader from the Adobe web site

and install it.

The external appearance and other parts shown in this manual may differ from the actual product within the

scope that will not interfere with normal use due to improvement of the product.

Standard accessories

Installation Guide (this document) 1 set ........................

IMPORTANT SAFETY INSTRUCTIONS 1 pc. ...............

Warranty card*1 ...................................................1 set

CD-ROM*2 .......................................................... 1 pc.

Code label*3........................................................ 1 pc.

*1 This product comes with several types of warranties. Each warranty is only applicable to the products pur-

chased in the regions indicated on the relevant warranty.

*2 The CD-ROM contains the operating instructions and different kinds of tool software programs.

*3 This label may be required for network management. Use caution not to lose this label.

Before requesting service, refer to the Important Information (included in the CD-ROM) and

“Troubleshooting” in the Operating Instructions (included in the CD-ROM) and confirm the

trouble.

: Direct current symbol

• Before attempting to connect or operate this product, please read these instructions carefully and

save this manual for future use.

• For information about the basic description of this product, refer to the Important Information on

the provided CD-ROM. For information about how to perform the settings and how to operate the

camera, refer to the Operating Instructions on the provided CD-ROM.

• The model number is abbreviated in some descriptions in this manual.

For U.S. and Canada:

Panasonic System Communications

Company of North America,

Unit of Panasonic Corporation

of North America

www.panasonic.com/business/

For customer support, call 1.800.528.6747

Two Riverfront Plaza, Newark, NJ 07102-5490

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga,

Ontario, L4W 2T3 Canada

(905)624-5010

www.panasonic.ca

For Europe and other countries:

Panasonic Corporation

http://www.panasonic.com

Panasonic Corporation

Osaka, Japan

Authorised Representative in EU:

Panasonic Testing Centre

Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, Germany

avs0717- 7 PGQX2189 A Printed in China210 X

*4 The power cable plug is attached to the camera.

The following parts are used during installation procedures.

Camera mount bracket (with safety wire) 1 pc. ............

Camera fixing screw (M3) 2 pcs. (incl. 1 spare) ...................................

Decorative cover 1 pc. .................................................

Power cable plug*4 ............................................. 1 pc.

Installation

The installation tasks are explained using 4 steps.

Examples of when using mount brackets (optional accessory) to install the camera

Preparations

Detach the camera

Place the camera upside-down

by  xing on the bracket or on a

desktop without  xing

⇨⇨

Step 2

Making connections ⇨

Step 1

Fix the mount bracket

and hang the camera

Step 4

Con gure the network

settings

Step 3

Fixing the camera

Other items that are needed (not included)

Preparations before installation

Prepare the required parts for each installation method before starting the installation. The following

are the requirements for the various installation methods.

Installation method

Mounting

screw

Minimum pull-

out strength*1

Ⓐ Installing the camera to a ceiling that has adequate

structural strength

Use the camera mount bracket (accessory).

M4 or M6

screws/4 pcs. 196 N {44 lbf}

Ⓑ Installing the camera to a ceiling that has inadequate

structural strength

The area of the ceiling that the camera will be installed to

must be sufﬁ ciently reinforced, or the optional ceiling mount

bracket for the camera (WV-Q105A*2, weight approx. 150 g

{0.33 lbs}) must be used.

M10 anchor

bolts/2 pcs.

5 times or more of

the total weight in-

cluding the camera

inadequate structural strength

The area of the ceiling that the camera will be installed

to must be sufﬁ ciently reinforced, or the optional ceiling

embedding bracket for the camera (WV-Q159C*2 / WV-

Q159S*2, weight approx. 800 {1.77 lbs}) must be used.g

M10 anchor

bolts/2 pcs.

5 times or more of

the total weight in-

cluding the camera

ⒹInstalling the camera to a wall

Use the wall mount bracket (WV-Q158C

*2 / WV-Q158S*2,

weight approx. 950 {2.10 lbs}).g

M4 screws/

4 pcs.

196 N {44 lbf}

*1 The minimum pull-out strength is the value per screw.

*2 For details on procedure for attaching mount bracket and camera, read the operating instruc-

tions of each mount bracket.

【1】Insert an SD memory card (locally

procured) as occasion demands.

* SDXC/SDHC/SD memory card is described as

SD memory card.

Insert an SD memory card following the procedure

shown below. For the detailed procedure, refer to

Important Information on the provided CD-ROM.

①As shown in the illustration to the right, push

the left side of the Panasonic logo plate to

unlock, then slide the SD memory card cover in

the direction of the arrow to open.

②Insert an SD memory card fully into the SD

memory card slot, and then push the memory

card straight into the slot until a click is heard.

(The label should face the bottom side of the

camera)

③Shut the SD memory card cover and lock the

cover by pushing the Panasonic logo plate.

Step 1 Fix the mount bracket and hang the camera 【3】Attach the safety wire fixed with

the camera mount bracket to

the camera.

After attaching the safety wire to the

camera, confirm that the ring part at

the end of the safety wire is securely

hooked on the safety wire holder.

Note:

• The camera is not fixed. Take

care not to hit the camera

against periphery (especially the

dome section).

• Retain a work space of 350 mm

{1 ft 1-25/32 inches} or more

from the ceiling when you hang

the camera from the ceiling.

IMPORTANT:

• To prevent an injury and protect the

cable, finish the side through hole for

the cable with a file so that it does not

become sharp.

• Make sure that no cable is pinched by

the decorative cover when installing it.

Ceiling mount bracket

(WV-Q105A)

Ceiling embedding bracket

(WV-Q159S / WV-Q159C)

Wall mount bracket

(WV-Q158S / WV-Q158C)

Ⓑ Ⓒ Ⓓ

【4】

Process the decorative cover

(accessory) as necessary.

Remove the cutout part on the

decorative cover when directly

attaching the cable to a ceiling with

open wiring. Install the camera and

wire through the cutout part of the

decorative cover as shown in the

illustration below when you finally fit the

decorative cover.

IMPORTANT:

• Prepare mounting screws (M4, M6) and anchor bolts to be mounted on a ceiling and wall

separately.

• Select screws according to the material of the location that the camera will be mounted to. In

this case, wood screws and nails should not be used.

• If the mounting location such as plaster board is too weak to support the total weight, the area

shall be sufficiently reinforced.

LOCK

OPEN

WV-S6130

Camera

mount bracket

(accessory)

Safety wire holder

Safety wire

Dome

section

IMPORTANT:

• Use the dedicated camera mount bracket (accessory) if installing the camera to a ceiling.

• Do not use the tripod screw hole to mount on the ceiling since the fall prevention measure is

unavailable. (See the illustration of

【

】

on the upper-right)

* The upper-right figure shows an illustration with the M4 screws used.

Tripod screw hole

350 mm

{1 ft 1-25/32 inches}

LOCK

OPEN

LOCK

Decorative cover

(accessory)

FRONT

OPEN

LOCK

Wiring hole

(ø25 mm {31/32 inches})

Camera mount bracket

(accessory)

75 mm

{2-15/16 inches}

83.5 mm

{3-9/32 inches}

46 mm

{1-13/16 inches}

64 mm

{2-17/32 inches}

110 mm

{4-5/16 inches}

Screw (M6)

100 mm

{3-15/16 inches} or more

away from obstacles such as wall

Screw (M4)

Front direction of the camera

Bottom side

Label facing

bottom side

SD memory card cover

Panasonic logo plate

SD memory

card slot

Left side of the Panasonic logo plate

The dimension of the decorative cover is ø185 mm {7-9/32 inches}.

The wiring hole can be covered with the decorative cover if its posi-

tion and size are as shown above.

【1】Rotate the decorative cover

(accessory) counterclockwise as

seen from the bottom until the

“OPEN” reaches the camera

mount bracket (accessory) protru-

sion to remove the cover.

IMPORTANT:

• Hold the decorative cover with both hands

when removing it.

【2】

Detach the 12 V DC power cable plug

(accessory) or the Ethernet cable from

the camera (When using PoE), and

then turn off the power of the camera.

IMPORTANT:

• Before turning off the camera power, hold down

the SD ON/OFF button (for about 2 seconds)

inside the SD memory card cover and make

sure that the SD MOUNT indicator is turned off.

If you turn off the camera power while the SD

MOUNT indicator is lit or flashing, the recorded

data may be corrupted or damaged.

【3】Remove the fixing screw (M3,

accessory) that is fixing the cam-

era on the camera mount bracket.

【4】Rotate the fixed section by approx.

20 ° counterclockwise to detach

the camera from the camera

mount bracket.

IMPORTANT:

• When detaching the camera from the

camera mount bracket, hold the fixed

section of the unit. Detaching the camera

while holding the dome section may

result in malfunction.

Note:

• Take care not to hit the camera

(especially the dome section)

against surrounding objects as the

camera is unfixed.

【5】Disconnect the remaining con-

nected cables from the camera.

【6】Detach the safety wire from the

camera and take off the camera

from the camera mount bracket.

Step 2 Making connections

【1】Connect an Ethernet cable (category 5e or better, straight) to the network

connector.

【2】If needed, connect a microphone or the line out of an external device to

the audio input connector.

【3】If needed, connect a powered speaker to the audio output connector.

■

Refer to the Important Information on the provided CD-ROM for details about

each cable.

●As necessary, use a cable tie (locally procured) to tie the cables together.

* Make sure to use the stereo mini plug.

Step 3 Fixing the camera

Note:

• Since the space around

the connector is limited,

use audio cables and an

Ethernet cable that do not

exceed the sizes described

in the illustrations.

Example of

audio cable connector

30 mm

{1-3/16 inches}

Straight section

17 mm {21/32 inches}

Straight section

30 mm {1-3/16 inches}

40 mm {1-9/16 inches}

13 mm

{1/2 inches}

9 mm

{11/32 inches}

Example of

Ethernet cable connector

ø9 mm

{11/32 inches}

IMPORTANT:

• Turn off each system’s power supply (PoE hub or device to supply power to the camera)

before making a connection.

• The 12 V DC power supply shall be insulated from the commercial AC power.

【】1 Network connector

INITIAL SET button

【】4 12 V DC power supply terminal

【】5 EXT I/O terminals

【】2 Audio input connector*

【】3 Audio output connector*

Monitor out connector

【4】When connecting an AC adaptor or an external power supply, use the power

cable plug (accessory) to connect it to the camera.

① Remove 3 mm - 7 mm {1/8 inches - 9/32 inches} of

the outer jacket of the cable for the AC adaptor,

expose the wire more and twist the stripped part of

the wire sufficiently.

When connecting an external power supply to the

camera, use the 16 AWG to 24 AWG single-wired

or stranded wired cables.

② Loosen the screws of the power cable plug and

insert the wire for the AC adaptor into the plug.

③ Tighten the screw of the power cable plug.

(Recommended tightening torque: 0.34 N·m

{0.25 lbf·ft})

④ Install the power cable plug into the camera.

Caution:

• A READILY ACCESSIBLE DISCONNECT DEVICE SHALL BE INCORPORATED TO THE

EQUIPMENT POWERED BY 12 V DC POWER SUPPLY.

• ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or LIMITED

POWER SOURCE (IEC/EN/UL/CSA 60950-1).

【5】If needed, connect the alarm input/output cables to the EXT I/O terminals.

Connect the cables of external devices to the EXT I/O terminal.

① Remove 8 mm - 9 mm {5/16 inches - 11/32 inches} of the outer jacket of the cable and twist

the cable core to prevent the short circuit first. Specification of cable (wire): 20 AWG - 26

AWG, Single core, twisted

② Push down the button of the desired terminal on the external I/O terminal plug with a ballpoint

pen, and release the button when the cable of the external device is fully inserted into the ter-

minal hole.

Note:

• Do not connect 2 wires or more directly to a terminal. When it is necessary to connect 2

or more wires, use a splitter.

• Check whether the stripped part of the wire is not exposed and is securely connected.

• The default of EXT I/O terminals is “Off”. Refer to the Operating Instructions on the pro-

vided CD-ROM for further information about the EXT I/O terminal settings.

External I/O terminal

4321

GND

ALARM IN3 (Terminal 3)

(Alarm input / AUX output)

ALARM IN2 (Terminal 2)

(Alarm input / Alarm output)

ALARM IN1 (Terminal 1)

(Alarm input / Black & white input / Auto time adjustment input)

Button

Strip range

Approx. 3 mm - 7 mm

{1/8 inches - 9/32 inches}

−+

(+) white/black cord

(12 V DC)

(–) black cord

(GND)

Power cable

plug (accessory)

【1】

Mount the camera onto the camera mount

bracket (accessory) and  x it temporarily.

①

Remove the protective tube (for protection

during transportation) covering the lock plate.

②

Fit the lock plate of the camera onto the

guide part of the camera mount bracket,

insert the camera with the center of the

camera (tripod screw hole) at the center of

the camera mount bracket, rotate the cam-

era clockwise by 20 ° as seen from the bot-

tom while pushing the camera against the

camera mount bracket and fix it temporarily.

IMPORTANT:

• When mounting the camera onto the cam-

era mount bracket, hold the fixed section of

the unit. Mounting the camera while holding

the dome section may result in malfunction.

【2】Fix the camera on the camera

mount bracket using the camera

 xing screw (M3, accessory).

Recommended tightening torque: 0.68 N·m

{0.50 lbf·ft}

* Wires connected to the camera are omitted in

the illustrations.

【3】Fit the “OPEN” of the decorative

cover onto the camera mount

bracket protrusion and insert the

decorative cover straight.

【4】

Rotate the decorative cover clockwise

as seen from the bottom until the

“LOCK” of the decorative cover

reaches the camera mount bracket

protrusion to  x the decorative cover.

IMPORTANT:

• Make sure that no cable is pinched by the

decorative cover.

【5】Remove the cover  lm from the

dome cover after the installation is

completed, and then turn on the

camera.

IMPORTANT:

• Once the camera is turned on, it starts to

be initialized and panning/tilting/zoom/

focus automatically operate. Do not touch

the dome section with your hand while

the camera is rotating.

Detach the camera

Place the camera upside-down by fixing on the bracket or on a desktop without fixing

• When using the camera upside-down by fixing on the bracket, fit it into the camera mount

bracket and fix it to prevent a fall or preset positional displacement. If necessary, attach the

decorative cover to the camera.

• When using the camera upside-down on a desktop, place the camera on a level place not

subject to vibrations. Ensure that the camera does not fall.

•

When using the camera upside-down by fixing on the bracket or on a desktop, select “On (desktop)”

for “Upside-down” on the [Cam. Function] tab of the setup menu. ( Operating Instructions)☞

■

The status indicator will light or blink as follows depending on the

camera status. (Refer to the procedure【1】illustration of “Detach the camera”.)

Operation status Indicator status

When the power is

turned on

Before the network con-

nection is established

Lights orange Lights off → →

Blinks orange Lights orange→

When the network con-

nection is established

Lights orange Lights off Blinks → →

orange Blinks green Lights green→ →

During the standby or

connection

Cable is not connected Lights orange

Cable is connected Lights green

During the upgrade process Blinks orange

Initialization (When the network connection is

established)

Lights orange Lights off Blinks → →

orange Lights orange Blinks → →

orange Blinks green Lights green→ →

Port forwarding error caused by the UPnP function Blinks orange (in 2 seconds intervals

(on for 1 second/off for 1 second))

Trouble happening on the camera Blinks red

Failure in writing data on the SD memory card Lights red

Note:

• When using the camera upside-down on a desktop with an external power supply, pass the

power cable through the cable guides (3) to prevent the AC adaptor plug from coming out.

On a desktopOn the bracket

Camera mount bracket

(accessory)

MONITOR OUT

MIC/LINE IN

EXT I/OEXT I/O

4 3 2 14 3 2 1

Power cable

Cable guides

FRONT

OPEN

LOCK

Approx.

20 °

Guide part

Fixed section

Center of the camera mount bracket

Lock plate

Fixing screw

(accessory)

LOCK

OPEN

Camera mount bracket (accessory) protrusion

Decorative cover

(accessory)

LOCK

OPEN

LOCK OPEN

Camera mount bracket

(accessory) protrusion

Status

indicator

Step 4 Configure the network settings

Configure the setting of the camera after temporarily invalidating the firewall software. Once the

camera configuration is completed, return to the original state.

Contact the network administrator or your Internet service provider for information about configuring

the settings of the network.

【1】Insert the provided CD-ROM into the CD-ROM drive of your PC.

• The License Agreement will be displayed. Read the Agreement and choose “I accept the term in

the license agreement”, and click [OK].

⇒ The launcher window will be displayed.

Note:

• If the launcher window is not displayed,

double click the “CDLauncher.exe” file

on the CD-ROM.

• Refer to “Using the CD-ROM” in the

Operating Instructions on the provided

CD-ROM for further information about

CDLauncher.

【2】Click the [Run] button next to [IP Setting Software].

⇒

[Panasonic IP Setting Software] screen will be displayed.

The MAC Address / IP address of the detected camera will be displayed.

【3】Select the camera you want to configure (

➀), and click [Network Settings] (➁)

to change the network settings. Then, click [Access Camera] (

➂).

Note:

• Select the camera with same MAC address as the MAC address printed on the camera that

you want to configure.

➀

➂

【4】When the administrator registration window is displayed, enter “User

name”, “Password” and “Retype password” by following the instructions

displayed on the screen, and then click the [Set] button.

Please keep your user name and password in a safe place free from public view to ensure

security.

After completing the registration, the camera will automatically be re-connected and the

authentication window will be displayed. Enter the registered user name and password.

The default setting of

user authentication

is “On”. For further

information, refer to

the “Preface” sec-

tion in the Operating

Instructions.

IMPORTANT:

• When the camera is used over the Internet, setting user authentication to “Off” may lead

to unintended access by a third party. Please leave user authentication set to “On”.

【5】When live images from the camera are displayed, the network connection

is complete.

Note:

For more information on the following content, refer to the Operating Instructions.

•

Please set [Time & date] on the [Basic] screen of “Setup” before using the camera.

• It is impossible to display H.265 (or H.264) or MJPEG images, receive/transmit audio,

display logs, and use full-screen display when the viewer software “Network Camera

View 4S” is not installed on the PC. Push the [Viewer Software] button on the live screen

to install the software as necessary.

• Depending on the environment of your PC, it may take time for images to be displayed.

• At the time of purchase, [Audio transmission mode] is set to “Off”. If needed, change the

setting on the [Audio] tab on the “Image/Audio” page in “Setup”.

• Due to security enhancements in “IP Setting Software”, “Network settings” cannot be

changed when around 20 minutes have passed after turning on the power of the camera

to be configured. (When the effective period is set to “20 min” in the “Easy IP Setup

accommodate period”.) However, settings can be changed after 20 minutes for cameras

in the initial set mode.

If images are not displayed, set the Web browser to compatibility view. For details on how to

configure, refer to our website (http://security.panasonic.com/support/info/)

➁

Camera mount bracket

(accessory)

Dome section

LOCK

OPEN

LOCK OPEN

Camera

mount bracket

(accessory)

protrusion

Dome cover

Fixing screw

(accessory)

Fixed section

Dome section

Produktspezifikationen

Marke:	Panasonic
Kategorie:	Überwachungskamera
Modell:	WV-S6130

Brauchst du Hilfe?

Wenn Sie Hilfe mit Panasonic WV-S6130 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Überwachungskamera Panasonic

Panasonic WV-SFN480 Bedienungsanleitung

2 Oktober 2024

Panasonic AW-HN130 Bedienungsanleitung

10 September 2024

Panasonic WV-CP630/G Bedienungsanleitung

9 September 2024

Panasonic AW-UE100K Bedienungsanleitung

28 August 2024

Panasonic AW-UR100 Bedienungsanleitung

20 August 2024

Panasonic WV-U2540L Bedienungsanleitung

3 August 2024

Panasonic WV-SF438E Bedienungsanleitung

1 August 2024

Panasonic AW-HN40H Bedienungsanleitung

29 Juli 2024

Panasonic AW-UE150WE Bedienungsanleitung

25 Juli 2024

Panasonic AW-UE50 Bedienungsanleitung

24 Juli 2024

Bedienungsanleitung Überwachungskamera

Neueste Bedienungsanleitung für -Kategorien-

Trebs CCD-401C Bedienungsanleitung

15 Oktober 2024

D-Link DCS-7510 Bedienungsanleitung

15 Oktober 2024

Foscam FI9900EP Bedienungsanleitung

14 Oktober 2024

Alecto DVC-215IP Bedienungsanleitung

14 Oktober 2024

Hikvision DS-2CD2326G2-IU Bedienungsanleitung

13 Oktober 2024

Hikvision DS-2TD2166-15/V1 Bedienungsanleitung

13 Oktober 2024

Hikvision DS-2DE7A245IX-AE/S1 Bedienungsanleitung

13 Oktober 2024

Hikvision DS-2CD7A26G0-IZ(H)SY Bedienungsanleitung

11 Oktober 2024

Hikvision DS-2CE79DF8T-AZE Bedienungsanleitung

11 Oktober 2024

Hikvision DS-2XM6726G0-I(D)(S)(M)(/ND) Bedienungsanleitung

11 Oktober 2024