Panasonic WV-S3532LM Bedienungsanleitung

Panasonic Überwachungskamera WV-S3532LM

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Panasonic WV-S3532LM (2 Seiten) in der Kategorie Überwachungskamera. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

Before requesting service, refer to “Troubleshooting” of Important Information in the CD-ROM

and Operating Instructions on the Panasonic support website. Then, confirm the trouble.

Preparations

Step 1 Processing the ceiling or wall

Network Camera

Installation Guide

Included Installation Instructions

Important safety instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

S3131

S3111

6) Clean only with dry cloth.

S3131

S3111

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

8) Only use attachments/accessories specified by the manufacturer.

9) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury

from tip-over.

S3125A

10) Unplug this apparatus during lightning storms or when unused for long periods of time.

11) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been dam-

aged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally,

or has been dropped.

Troubleshooting

Open Source Software

• This product contains open source software licensed under GPL (GNU General Public License),

LGPL (GNU Lesser General Public License), etc.

• Customers can duplicate, distribute and modify the source code of the software under license of

GPL and/or LGPL.

• Refer to the “readme.txt” file on the provided CD-ROM for further information about open source

software licenses and the source code.

• Please note that Panasonic shall not respond to any inquiries regarding the contents of the source

code.

NOTE: This equipment has been tested and found

to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference when the equipment is

operated in a commercial environment. This equip-

ment generates, uses, and can radiate radio fre-

quency energy and, if not installed and used in

accordance with the instruction manual, may cause

harmful interference to radio communications.

Operation of this equipment in a residential area is

likely to cause harmful interference in which case

the user will be required to correct the interference

at his own expense.

FCC CAUTION: Changes or modifications not

expressly approved by the party responsible for

compliance could void the user’s authority to oper-

ate the equipment.

For U.S.A.

The model number and serial number of this prod-

uct may be found on the surface of the unit.

You should note the model number and serial num-

ber of this unit in the space provided and retain this

book as a permanent record of your purchase to

aid identification in the event of theft.

Model No.

Serial No.

For U.S.A.

CAN ICES-3(A)/NMB-3(A)

For Canada

WARNING:

• To prevent injury, this apparatus must be securely

attached to the wall/ceiling in accordance with the

installation instructions.

• To prevent fire or electric shock hazard, do not

expose this apparatus to rain or moisture.

S3131

S3111

• The apparatus should not be exposed to dripping

or splashing.

S3131

S3111

• All work related to the installation of this product

should be made by qualified service personnel or

system installers.

• The installation shall be carried out in accordance

with all applicable installation rules.

• The connections should comply with local electrical

code.

• Batteries (battery pack or batteries installed) shall

not be exposed to excessive heat such as sunlight,

fire or the like.

CAUTION:

• The network camera is only intended for a connec-

tion to an ethernet or PoE network without routing

to the outside plant.

Disposal of Old Equipment and Batteries

Only for European Union and countries with recycling systems

These symbols on the products, packaging, and/or accompanying documents mean that used

electrical and electronic products and batteries must not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them

to applicable collection points in accordance with your national legislation.

By disposing of them correctly, you will help to save valuable resources and prevent any potential

negative effects on human health and the environment.

For more information about collection and recycling, please contact your local authority.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national

legislation.

Note for the battery symbol (bottom symbol)

This symbol might be used in combination with a chemical symbol. In this case it complies with the

requirement set by the Directive for the chemical involved.

About the user manuals

Product documentation is composed of the following documents.

• Installation Guide (this document): Explains installation, mounting, cable connections, and adjusting the

ﬁ eld of view.

• Important Information (included in the CD-ROM):

Provides basic information about this product such

as Precautions for installation, Parts and functions, etc..

• Operating Instructions (on the Panasonic support website): Explains how to perform the settings

and how to operate this product.

Standard accessories

Installation Guide (this document) ..............1 pc.

IMPORTANT SAFETY INSTRUCTIONS ......1 pc.

Warranty card ............................................1 pc.

CD-ROM*1 ................................................. 1 pc.

Code label*2...............................................1 pc.

*1 The CD-ROM contains the several kind of operating instructions and different kinds of tool soft-

ware programs.

*2 This label may be required for network management. Use caution not to lose this label.

The following parts are used during installation procedures.

Template ....................................................1 pc.

S3531

S3511

S3532

S3512

Bit

(Hex wrench,

screw size 6.35 mm {1/4 inches} T10)

.............1 pc.

S3531

S3511

RJ45 waterproof connector cover .............1 pc.

RJ45 waterproof connector cap ................1 pc.

S3532

S3512

Cable guard ...............................................1 pc.

Lens adjuster ..............................................1 pc.

* Lens adjuster is used only at the time of servic-

ing.

IMPORTANT:

• When replacing existing models (WV-SFV130/WV-SFV110/WV-SW155/WV-SW158) and

installing to a one-gang junction box, take care because the direction of the camera will

change 90° to the side.

S3531 S3511 S3532 S3512

• The minimum required pull-out capacity of a single screw or anchor bolt is 196 N {44 lbf} or

more.

• Select screws according to the material of the location that the camera will be mounted to.

In this case, wood screws and nails should not be used.

• If the mounting location such as plaster board is too weak to support the total weight, the

area shall be sufficiently reinforced.

Bit

: Direct current symbol

【Connecting the cable through holes opened in the ceiling or wall】

• Before attempting to connect or operate this product, please read these instructions carefully and

save this manual for future use.

• For information about the basic description of this product, refer to the Important Information on

the provided CD-ROM. For information about how to perform the settings and how to operate this

product, refer to the Operating Instructions on the following Panasonic support website.

https://security.panasonic.com/download/

• Before reading this manual, be sure to read the Important Information.

Note:

• The external appearance and other parts shown in this manual may differ from the actual prod-

uct within the scope that will not interfere with normal use due to improvement of the product.

• "<Control No.: C****>" used in this document should be used to search for information on

the Panasonic support website and will guide you to the right information.

Model No. WV-S3531L, WV-S3511L

WV-S3131L, WV-S3111L

WV-S3532LM, WV-S3512LM

WV-S3531L

The following notations are used when describing the functions limited for specified models.

The functions without the notations are supported by all models.

:The functions with this notation are available when using the model WV-S3531L.

:The functions with this notation are available when using the model WV-S3511L.

:The functions with this notation are available when using the model WV-S3131L.

:The functions with this notation are available when using the model WV-S3111L.

:The functions with this notation are available when using the model WV-S3532LM.

:The functions with this notation are available when using the model WV-S3512LM.

XXXXX

: Outdoor model

XXXXX

: Indoor model

About notations

S3531

S3511

S3131

S3111

S3532

S3512

■

The following are methods for installing a camera to a ceiling or wall

Prepare the required parts for each installation method before starting the installation.

The following are the requirements for the various installation methods.

Installation method

Mounting screws

/ anchor bolts

When directly installing a camera to a ceiling or wall M4 / 3 pcs.

When installing to a junction box or other part.

S3531

S3511

S3532

S3512

When installing the junction box cover (locally procured), prepare a locally procured

metal cover according to the shape of the junction box.

M4 / 2 pcs.

Place the template (accessory) on the ceiling or wall, mark the holes for the cable to be passed

through and for the fixing screws (3 places), then open the holes.

IMPORTANT:

• Turn off each system’s power supply (PoE hub, etc.) before starting the installation.

• Perform waterproofing so that there is no exposure to water into the architecture through the

holes for the camera fixing screws or hole for wiring.

S3531 S3511 S3532 S3512

Note:

• Use the template (accessory) with the side with the arrow facing you.

• Ceiling installation:

Place the template so that the arrow is pointing to the front of the camera (the lens side).

• Wall installation:

Place the template so that the arrow is pointing down.

• No processing for the ceiling or wall is required when installing the camera to an existing junc-

tion box.

S3531 S3511 S3532 S3512

【Connecting the cable through the side cable access hole】

Place the template (accessory) on the ceiling or wall, mark the holes for the fixing screws (3 places),

then open the holes.

Using the bit (accessory), loosen the

enclosure ﬁ xing screws (3 places).

Hold the both sides of the enclosure

and remove it.

Remove the packaging from the

inside of the dome cover.

Use a ﬂ athead screwdriver to open the

screw cover (2 places), and then use a

Phillips screwdriver to loosen the enclo-

sure ﬁ xing screws (2 places).

Hold down on both sides of the enclo-

sure and remove it.

Remove the packaging from the inside

of the dome cover.

IMPORTANT:

• To prevent injuries and protect the cables,

finish the side cable access portion with a file

to avoid sharp edges.

Side cable

access hole

S3531 S3511 S3532 S3512 S3131 S3111

Holes for the fixing screws (3 places)

Template (accessory)

Arrow

*12 mm {15/32 inches}

10.5 mm {13/32 inches}

*27 mm{1-1/16 inches}

30.5 mm{1-3/16 inches}

Cable access

hole

When installing the camera directly on the ceiling or

wall with cables exposed, cut out a portion of the

enclosure to open a cable access hole on the side of

the enclosure, and then pass the cables through the

side of the enclosure.

Follow the steps below to insert the microSD

memory card if necessary.

Insert the microSD memory card into the

microSD slot with the side with printing

facing up.

Insert the microSD memory card into the end

of the microSD slot and confirm that a click-

ing sound is made.

After confirming a clicking sound is made,

take your fingers off the microSD memory

card and ensure that its back end does not

protrude over the surface of the microSD slot

(the same surface as the microSD symbol).

For information about inserting and removing

microSD memory cards, refer to the Important

Information on the provided CD-ROM.

*This illustration represents WV-S3131L

Note:

•

After the installation is completed, do not remove the cover film from the dome cover until

attaching the enclosure.

•

Because the cable part and the slot for the waterproof rubber are engaged, it may be difficult to

take off the enclosure.

S3531 S3511 S3532 S3512

WV-S3131L

This device complies with Part15 of the FCC Rules.

Operation is subject to the following two conditions :

(1)This device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

Supplier’s Declaration of conformity

Trade name : Panasonic

Model No. :

WV-S3531L, WV-S3511L

WV-S3131L, WV-S3111L

WV-S3532LM, WV-S3512LM

Responsible Party :

Panasonic Corporation of North America

Two Riverfront Plaza, Newark, New Jersey

07102-5490

Support Contact : 1-800-528-6747

Other items that are needed (not included)

Processing of side cable access hole

S3131

S3111

Inserting a microSD memory card

Removing the enclosure

Enclosure fixing screws (2 places)

Enclosure fixing

screws (3 places)

Bit (accessory)

Waterproof

rubber

Enclosure

Slot of the waterproof

rubber

Screw

cover

Screw

cover

Dome cover

Step1

Processing the ceiling

or wall

Step2

Making connections

⇨

• Remove the camera using the reverse order of the installation procedures.

The installation tasks are explained using 6 steps.

Installation

Step3

Mount the camera

⇨ ⇨ Step4

Conﬁ gure the network

settings

Step5

Adjustment

⇨Step6

Attach the enclosure

⇨

Step 2 Making connections

S3131

S3111

RJ45 Network terminal

Ethernet cable (locally procured)

(category 5e or better, straight)

Connect an Ethernet cable to RJ45 network terminal.

IMPORTANT:

• The maximum cable length is 100 m {328 feet}.

96 mm {3-25/32 inches}

88.6 mm {3-1/2 inches}

*23°

24°

*36°

37.5°

*36°

39.5°

*22 mm{7/8 inches}

17 mm{21/32 inches}

*22 mm {7/8 inches}

17 mm{21/32 inches}

*Upper level：

S3531

S3511

S3532

S3512

Holes not explained in the

illustration are not used.

Lower level：

S3131

S3111

Symbol of

the microSD

microSD memory card (the

side with printing facing up)

microSD slot

Back end of the microSD memory card

For U.S. and Canada:

Panasonic i-PRO Sensing Solutions

Corporation of America

800 Gessner Rd, Suite 700 Houston, TX 77024

https://www.security.us.panasonic.com/

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada

1-877-495-0580

https://www.panasonic.com/ca/

avs1218-2109 PGQX2273XA Printed in China

For Europe and other countries:

Panasonic Corporation

http://www.panasonic.com

Panasonic i-PRO Sensing Solutions Co., Ltd.

Fukuoka, Japan

Authorised Representative in EU:

Panasonic Testing Centre

Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, Germany

Step 2 Making connections

S3531

S3511

S3532

S3512

IMPORTANT:

• The external dimensions of the Ethernet cable are from ø5 mm {ø3/16 inches} to ø6.5 mm {ø1/4inches}.

• If the procedure for the RJ45 waterproof connector (accessory) part is not correctly followed, the

waterproofing may be compromised. Do not install the camera where the RJ45 waterproof connector

is exposed to constant rain or moisture.

• When removing the RJ45 waterproof connector, be sure to loosen the RJ45 waterproof connector

cap first, rotate the RJ45 waterproof connector cover in the direction opposite to the attaching

direction, and remove it. (If the RJ45 waterproof connector cover is removed when the “

⇦

” mark of

the RJ45 waterproof connector cover is aligned with the “

▶” mark of the RJ45 waterproof jack, the

RJ45 waterproof jack may be damaged)

Connect an Ethernet cable (category 5e or better, straight) to RJ45 network cable.

RJ45 Network cable

S3531

S3511

Ethernet cable (locally procured)

(category 5e or better, straight)

The maximum cable length is

100 m {328 feet}.

AFirst pass the Ethernet cable through the RJ45

waterproof connector cap (accessory) and then

through the RJ45 waterproof connector cover

(accessory). Next, use a specialized tool (locally

procured) to crimp the RJ45 plug (locally procured)

to the end of the Ethernet cable.

• Take care not to remove the rubber parts from

inside the RJ45 waterproof connector cover.

BInsert the RJ45 plug into the RJ45 waterproof jack

connected to the camera.

CConnect the RJ45 waterproof connector cover to the

RJ45 waterproof jack and then rotate the RJ45

waterproof connector cover until the " " marks align.⇦

DConnect the RJ45 waterproof connector cap to the

RJ45 waterproof connector cover and rotate the

RJ45 waterproof connector cap until there is no gap

between it and the RJ45 waterproof connector cover.

RJ45

plug

(locally

pocured)

RJ45

waterproof

connector

cover

(accessory)

RJ45

waterproof

connector

cap

(accessory)

Ethernet

cable

RJ45

waterproof

jack

Step 3 Mount the camera

IMPORTANT:

• Prepare the fixing screws (2 pcs.) (M4:

locally procured) according to the specifi-

cations of screw holes of the two-gang

junction box to be used.

IMPORTANT:

• Do not touch the lens.

• When tightening the screws (locally procured), be careful to ensure that the fixing screws does

not tangle the cable.

【1】

Mount the camera

■

Installing the camera directly on the ceiling or wall

Secure the camera with ﬁ xing screws (3 pcs.) (M4:locally procured).

The minimum required pull-out capacity:196 N {44 lbf} /single screw

When the camera is installed on a ceiling or wall and you open a whole to pass cables through the rear of

the camera, use a cable guard (accessory) so that the cables are not visible from the outside. When ﬁ xing

the camera to the ceiling or wall, also tighten the cable guard.

S3532

S3512

■

Using a two-gang junction box

S3531

S3511

S3532

S3512

Install the camera to the two-gang junction box

using screws (2 pcs.) (M4: locally procured).

【2】

After the camera is secured, connect power to the system. (power from a PoE hub, etc.)

Fixing screws (3 pcs.)

(M4: locally procured)

Tighten the 2 fixing screws on the lens side by using

the slotted holes on the front side of the camera.

* Image of the shape of a junction box.

Fixing screws (2 pcs.) (M4: locally procured)

Step 4 Configure the network settings

Configure the setting of the camera after temporarily invalidating the firewall software. Once the

camera configuration is completed, return to the original state.

Contact the network administrator or your Internet service provider for information about config-

uring the settings of the network.

【2】Click the [Run] button next to [IP Setting Software].

⇒[Panasonic IP Setting] screen will be displayed.

The MAC Address / IP address of the detected camera will be displayed.

【1】Insert the provided CD-ROM into the CD-ROM drive of your PC.

The License Agreement will be displayed. Read the Agreement and choose “I accept the

term in the license agreement”, and click [OK].

⇒The launcher window will be displayed.

Note:

• If the launcher window is not displayed,

double click the “CDLauncher.exe” file on

the CD-ROM.

• Refer to “Using the CD-ROM” in the

Operating Instructions on the Panasonic

support website for further information

about CDLauncher

Note:

For more information on the following content, refer to the Operating Instructions on the

Panasonic support website.

• Please set [Time & date] on the [Basic] screen of “Setup” before using the camera.

• It is impossible to display H.265 (or H.264) or MJPEG images, receive audio, display logs, and

use full-screen display when the viewer software “Network Camera View 4S” is not installed on

the PC.

• Depending on the environment of your PC, it may take time for images to be displayed.

• At the time of purchase, audio mode is set to “Off”.If needed, change the setting on the “Audio”

screen in “Setup”.

• Due to security enhancements in “IP Setting Software”, “Network settings” cannot be changed

when around 20 minutes have passed after turning on the power of the camera to be

configured. (When the effective period is set to “20 min” in the “Easy IP Setup accommodate

period”.) However, settings can be changed after 20 minutes for cameras in the initial set mode.

If images are not displayed, set the Web browser to compatibility view. For details on how to

configure, refer to our website (https://security.panasonic.com/support/info/ <Control No.: C0104>)

【3】

Select the camera you want to configure ( ), and click [Network Settings] A

( ) to chance the network settings. Then, click [Access Camera] ( ).B C

Note:

Select the camera with same MAC address as the MAC address printed on the camera that

you want to configure.

【4】When the administrator registration window is displayed, enter “User

name”,“Password” and “Retype password” by following the instructions

displayed on the screen, and then click the [Set] button.

IMPORTANT:

• When the camera is used over the Internet, setting user authentication to “Off” may lead to

unintended access by a third party. Please leave user authentication set to “On”.

【5】When live images from the camera are displayed, the network connection

is complete.

Please keep your user name and

password in a safe place free from

public view to ensure security.

After completing the registration,

the camera will automatically be

re-connected and the

authentication window will be

displayed. Enter the registered

user name and password.

The default setting of user

authentication is “On”. For further

information, refer to the “Preface”

section in the Operating

Instructions on the Panasonic

support website.

S3531 S3511 S3532 S3512

M12 (female) Network cable

S3532

S3512

M12 (male) plug

【1】 Attach the enclosure

S3531 S3511 S3532 S3512

IMPORTANT:

• Check that the waterproof rubber installed in the slot around the camera does not slide out of

the slot, and then mount the enclosure.

• If the enclosure is attached keeping it parallel to the camera body, the inside of the dome cover

may collide with the camera unit and cause deviation of the set angle of view.

• Securely tighten fixing screws (3 places) of enclosure. Otherwise, water exposure may cause

damage or malfunction of camera, or enclosure dropping may result in injury.

Recommended tightening torque: 0.8N·m {0.59 lbf·ft}

A Attach the enclosure matching the dome cover side of the enclosure and the camera front

( -mark in the illustration below) so that the camera unit is covered by the dome cover.★

B Attach the enclosure to the camera by using the bit (accessory) to tighten the enclosure fixing

screws (3 places).

IMPORTANT:

• After removing the cover film, do not touch the dome cover with your hands.

Enclosure fixing screws

(3 places)

Bit (accessory)

Fixing screws (3 pcs.)

(M4: locally procured)

S3131 S3111

Step 6 Attach the enclosure

【1】Attach the enclosure

A Attach the enclosure matching the dome cover side of the enclosure and the camera front

( -mark in the illustration below) so that the camera unit is covered by the dome cover.★

B Tighten the fixing screws of the enclosure (2 places) with a Phillips screwdriver.

C Close the screw cover.

Enclosure fixing screws

(2 places)

Enclosure

S3131 S3111

IMPORTANT:

• If the enclosure is attached keeping it parallel to the camera body, the inside of the dome

cover may collide with the camera unit and cause deviation of the set angle of view.

• Securely tighten fixing screws (2 places) of enclosure.

Otherwise, the enclosure of the camera dropping may result in injury.

Recommended tightening torque: 0.4N·m {0.3 lbf·ft}

Parts and functions

S3131 S3111 RJ45 network terminal

S3531 S3511 S3532 S3512

RJ45 Network cable

S3531

S3511

*1 Depending on the scanning application used, the Data Matrix may not be able to be read correctly.

In this case, access the site by directly entering the following URL.

https://security.panasonic.com/support/qr_sp_select/

LINK indicator

• When the camera is able to communicate with the connected device

Lights orange

ACT indicator

• When data is being sent via the network camera Blinks green(accessing)

SD ERROR indicator

• When this product is being started Lights red

• When a microSD memory card is recognized normally Lights red Lights off→

• When the microSD slot is not used or an abnormality is detected in Lights red Stays red→

microSD memory card after the camera has started

Two-dimensional

barcode (Data Matrix):

To our website*1

S3531

S3511

S3532

S3512

Connect an Ethernet cable (category 5e

or better, straight) to M12 (female) net-

work cable. Ethernet cable

AInsert the M12 plug into the M12 Network cable

connected to the camera.

BTightly fasten the connector by rotating both

rings in opposite directions.

M12 (male) plug

M12 (female)

Network cable

83.5mm

{3-9/32 inches}

【2】 Remove the cover ﬁ lm from outside of the dome cover. 【2】 Remove the cover ﬁ lm from outside of the dome cover.

IMPORTANT:

• After removing the cover film, do not touch the dome cover with your hands.

M12 (female) Network cable

S3532

S3512

Screw cover Screw cover

Concave part of the camera

Front side

of camera

Cable guard (accessory)

S3532

S3512

INITIAL SET button

Built-in

microphone

microSD

slot

Waterproof

rubber

Camera unit

IR LED IR LED

★

Dome cover

The sheets and tapes on the dome cover fixing

part are not shown in the illustration.

★

Enclosure

Waterproof rubber

Dome cover

Seen from the camera

front Seen from the camera

front

The sheets and tapes on the dome cover fixing

part are not shown in the illustration.

IMPORTANT:

• When adjusting the camera angle, do not touch the lens.

Note:

• When the camera is installed on a wall, the gradient viewed from the camera is backwards.

Images displayed from the camera can be reversed by setting "Image rotation" to "180°

(Upside-down)" in the setup menu. For information about configuring "Image rotation" in the

setup menu, refer to the Operating Instructions on the Panasonic support website.

• Depending on the horizontal / vertical angle, the top, bottom, left, or right ends of the

camera may be visible.

• Use Extra zoom when you want to adjust the angular field of view on the "Tele" side. For

information about configuring "Extra zoom", refer to the Operating Instructions on the

Panasonic support website.

- When VGA (640x480) or a lower resolution is selected, the angular field of view can be

adjusted without deterioration in the image quality.

- When a resolution higher than VGA is used, image quality may deteriorate depending on

the zoom rate of the Extra zoom.

• When a strong light shines on the front of the camera, part of the lens may be reflected on

the inside of the dome cover and be visible in images. Adjust the camera angle so that there

are no reflections.

• When viewing images at night using IR LED, parts of the screen may be dark if the TILT is

75° or more (Azimuth (YAW) angle : 0°, factory setting position).

For image example and detail information, refer to our website (https://security.panasonic.

com/support/info/ < Control No.:C0118>).

• For information about displaying vertically long images, refer to our website(https://security.

panasonic.com/support/info/ < Control No.:C0119>).

* This illustration represents WV-S3131L

Horizontal (PAN)angle : ±45° Azimuth(YAW) angle : ±90°

Vertical (TILT) angle :75° (second scale)

Vertical (TILT) angle : 0° to 90°

0°

Adjust the camera’s angle of view

・ Adjust the horizontal (PAN) angle by pinching the side

parts of the camera unit ( ).󱓂

・ Adjust the azimuth (YAW) angle and vertical (TILT) angle.

A Loosen the TILT/YAW fixing screw.

Outside part

of the lens unit

Side part of

the camera

unit

Lens

TILT/YAW

fixing screw

Step 5 Adjustment

Lens unit

Upwards direction

on the monitor

Camera unit

Upwards

direction on

the monitor

90°

IMPORTANT:

• TILT/YAW fixing screw can be effective by

loosening it about 1 turn. Do not unscrew it

more than necessary.

Adjust the azimuth (YAW) angle and vertical (TILT) angle

by pinching the outside parts of the lens unit

( )󱓃

Fix each part by tightening the TILT/YAW fixing screw.

Recommended tightening torque: 0.2N·m {0.15 lbf·ft}

Produktspezifikationen

Marke:	Panasonic
Kategorie:	Überwachungskamera
Modell:	WV-S3532LM

Brauchst du Hilfe?

Wenn Sie Hilfe mit Panasonic WV-S3532LM benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Überwachungskamera Panasonic

Panasonic WV-SFN480 Bedienungsanleitung

2 Oktober 2024

Panasonic AW-HN130 Bedienungsanleitung

10 September 2024

Panasonic WV-CP630/G Bedienungsanleitung

9 September 2024

Panasonic AW-UE100K Bedienungsanleitung

28 August 2024

Panasonic AW-UR100 Bedienungsanleitung

20 August 2024

Panasonic WV-U2540L Bedienungsanleitung

3 August 2024

Panasonic WV-SF438E Bedienungsanleitung

1 August 2024

Panasonic AW-HN40H Bedienungsanleitung

29 Juli 2024

Panasonic AW-UE150WE Bedienungsanleitung

25 Juli 2024

Panasonic AW-UE50 Bedienungsanleitung

24 Juli 2024

Bedienungsanleitung Überwachungskamera

Neueste Bedienungsanleitung für -Kategorien-

Trebs CCD-401C Bedienungsanleitung

15 Oktober 2024

D-Link DCS-7510 Bedienungsanleitung

15 Oktober 2024

Foscam FI9900EP Bedienungsanleitung

14 Oktober 2024

Alecto DVC-215IP Bedienungsanleitung

14 Oktober 2024

Hikvision DS-2CD2326G2-IU Bedienungsanleitung

13 Oktober 2024

Hikvision DS-2TD2166-15/V1 Bedienungsanleitung

13 Oktober 2024

Hikvision DS-2DE7A245IX-AE/S1 Bedienungsanleitung

13 Oktober 2024

Hikvision DS-2CD7A26G0-IZ(H)SY Bedienungsanleitung

11 Oktober 2024

Hikvision DS-2CE79DF8T-AZE Bedienungsanleitung

11 Oktober 2024

Hikvision DS-2XM6726G0-I(D)(S)(M)(/ND) Bedienungsanleitung

11 Oktober 2024