Ozito PCS-254 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Ozito PCS-254 (9 Seiten) in der Kategorie Säge . Dieser Bedienungsanleitung war für 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/9
BRAKE OFF
RUN
PCS-254
5. Pull out the choke. (fully
withdrawn).
2. Remove the chain bar BLACK
oil cap and fill the tank to about
80% of its capacity with chain
bar oil. Chain bar oil tank capacity
160ml. Fasten the oil tank cap
and clean any spillage.
9. When ready to start cutting,
release the brake by pulling the
chain brake firmly towards the
rear of the chainsaw.
1. Place chainsaw on its side.
Remove the fuel tank cap RED
and fill the fuel tank up to the
filler neck with the fuel mix. Fuel
tank capacity 230ml. Fasten the
fuel tank cap and clean any
spillage.
3. For safety reasons, make sure
the brake is ON when starting. To
apply the brake, push the chain
brake forward.
8. Push in the choke. Now pull
the recoil starter several times
until the engine starts.
7. Hold the tool firmly on the
ground and pull out the recoil
starter until you feel it start to
resist. Pull firmly on the recoil
starter until it fires.
6. Press the priming bulb 10
times to push fuel into the
carburettor.
4. Move the ignition switch to the
“I” ON position.
BRAKE ON
START
2 Stroke
Oil
40:1
1
PETROL
CHAINSAW
25.4cc - 254mm (10”)
INSTRUCTION MANUAL
SPECIFICATIONS
Engine: 25.4cc 2 Stroke
Power: 0.7 kW
Bar: 254mm (10”)
Max. Cutting Capacity: 200mm (8”)
Chain Pitch: 9.525mm (3/8”)
No Load Speed: 11,000/min
Chain Speed: 21 m/s
Fuel Mix 40:1
Fuel Tank Capacity: 230ml
Chain Oil Tank Capacity: 160ml
Tool Weight: 3.8 kg
PCS-254
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
1 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 12 months from
the original date of purchase. If a product is defective it will
be replaced in accordance with the terms of this warranty.
Warranty excludes consumable parts, for example:
filters, spark plugs, chains and included accessories.
WARNING
The following actions will result in the warranty being void.
• Professional, Industrial or high frequency use.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
ozito.com.au
0
Petrol Chainsaw
Chain Bar Cover
Fuel Mixing Bottle
Spark Plug Wrench
Hex Key
1
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
KNOW YOUR PRODUCT SETUP & PREPARATION
1. Side Cover
2. Choke Control
3. Throttle Safety Release
4. Throttle Trigger
5. Ignition Switch
6. Chain Drive Cover Nuts
7. Chain Tension Screw
8. Chain
9. Guide Bar
1. ADJUSTING THE CHAIN TENSION
PETROL CHAINSAW
ACCESSORIES
1
10 11 12 13 14 15 16 17 18
2 3 4 5 6 7 8 9 Note: Proper tension of the chain is extremely important and
must be checked before starting, as well as during any cutting
operation. Taking the time to make adjustments to the chain
will result in improved cutting performance and prolonged
chain life.
Correct tension
For the correct chain tension, pull up
on the chain from the top and middle
of the exposed guide bar. The
bottom tip of the links should only
just stay in the track.
Adjusting tension
1. Loosen, but do not remove
the chain drive cover nut.
2. Adjustment chain tension
screw CLOCKWISE
to increase chain
tension. Turning screw
COUNTERCLOCKWISE will
decrease amount of tension
on the chain. Adjust the
chain tension screw for the
correct tension.
3. After making the
adjustment, tighten the
chain drive cover nut
securely.
WARNING! WEAR PROTECTIVE GLOVES AT ALL
TIMES WHEN HANDLING THE CHAIN.
WARNING! RECHECK THE TENSION AFTER A
FEW MINUTES OF CUTTING AS THE CHAIN MAY
STRETCH AFTER INITIAL USE. A LOOSE CHAIN MAY
CAUSE WEAR TO BOTH THE CHAIN AND THE GUIDE
BAR AND BECOME A MAJOR SAFETY HAZARD.
3mm gap is the
ideal tension
10. Bucking Spikes
11. Chain Bar Oil Cap
12. Chain Brake
13. Fuel Tank Cap
14. Priming Bulb
15. Rear Handle
16. Handle
17. Recoil Starter
18. Filter Cover Screw
19. Fuel Mixing Bottle
20. Hex Key
21. Spark Plug Wrench
22. Chain Bar Cover
19 20 21 22
Produktspezifikationen
| Marke: | Ozito |
| Kategorie: | Säge |
| Modell: | PCS-254 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Ozito PCS-254 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Säge Ozito
16 Mai 2024
24 Februar 2024
28 Januar 2024
18 Januar 2024
15 Januar 2024
14 Januar 2024
14 Januar 2024
15 Dezember 2023
11 Dezember 2023
6 Dezember 2023
Bedienungsanleitung Säge
- Säge Panasonic
- Säge Cotech
- Säge Makita
- Säge Bosch
- Säge Parkside
- Säge Vonroc
- Säge AEG
- Säge Powerfix
- Säge Black And Decker
- Säge Cocraft
- Säge FERM
- Säge Ryobi
- Säge Skil
- Säge Trotec
- Säge Hilti
- Säge Bort
- Säge DeWalt
- Säge Einhell
- Säge Elu
- Säge Festool
- Säge Mafell
- Säge Triton
- Säge Worx
- Säge Tacklife
- Säge Hikoki
- Säge Hitachi
- Säge Hyundai
- Säge Hazet
- Säge Kress
- Säge Metabo
- Säge Stanley
- Säge Kärcher
- Säge Atika
- Säge Güde
- Säge Power Craft
- Säge Scheppach
- Säge Bébé Confort
- Säge Workzone
- Säge Meec Tools
- Säge Dremel
- Säge Fieldmann
- Säge King Craft
- Säge Proxxon
- Säge Westfalia
- Säge Remington
- Säge Husqvarna
- Säge Stihl
- Säge Chicago Pneumatic
- Säge Dedra
- Säge Graphite
- Säge Snow Joe
- Säge Silverline
- Säge Holzmann
- Säge Sthor
- Säge Florabest
- Säge Hecht
- Säge Herkules
- Säge Stiga
- Säge Ford
- Säge Zipper
- Säge Yato
- Säge Baumr-AG
- Säge Greencut
- Säge Genesis
- Säge Evolution
- Säge Dolmar
- Säge Bavaria
- Säge Milwaukee
- Säge Narex
- Säge Toolcraft
- Säge Fein
- Säge AL-KO
- Säge Gardena
- Säge Craftsman
- Säge Defort
- Säge Powerplus
- Säge Alpha Tools
- Säge Martha Stewart
- Säge McCulloch
- Säge Yard Force
- Säge Sun Joe
- Säge Draper
- Säge Solo
- Säge Texas
- Säge Ridgid
- Säge Porter-Cable
- Säge Hobart
- Säge Guede
- Säge Dexter Power
- Säge Felisatti
- Säge Gardenline
- Säge Grizzly
- Säge Homelite
- Säge HURRICANE
- Säge Plantiflor
- Säge Qualcast
- Säge Shindaiwa
- Säge Sterwins
- Säge Tanaka
- Säge Troy-Bilt
- Säge Meister Craft
- Säge Sovereign
- Säge Challenge
- Säge Challenge Xtreme
- Säge Truper
- Säge MacAllister
- Säge RIKON
- Säge Pro-Cut
- Säge Selion
- Säge Kreg
- Säge Proviel
- Säge Merox
- Säge Bullcraft
- Säge XU1
- Säge MTM
- Säge Urrea
- Säge EFA
- Säge MyTool
- Säge Ergotools Pattfield
- Säge IKRA
- Säge FIXIT
- Säge Bavaria By Einhell
- Säge Rona
- Säge Donau Elektronik
Neueste Bedienungsanleitung fĂĽr -Kategorien-
14 August 2024
7 August 2024
28 Juni 2024
28 Juni 2024
28 Juni 2024
28 Juni 2024
26 Juni 2024
26 Juni 2024
26 Juni 2024
26 Juni 2024