OSD Audio IWS8 Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr OSD Audio IWS8 (6 Seiten) in der Kategorie Subwoofer. Dieser Bedienungsanleitung war fĂĽr 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
In-Wall Subwoofer Series Owners Manual
IWS-10 IWS-8
18AWG minimum - for distances up to ………………………. . 10 ft
16AWG - from ……………………………………………. 10 to 50 ft
14AWG - from …………………………………………… 50 to 100ft
- Where is the best place to install the speakers
- Where do the speakers sound the best
- Try to separate the speakers 6 - 10 feet apart.
- When placing the speakers in the wall, try to locate them so that the
sound is projected towards the general listening area.
- If you intend to paint the grilles, try to do so before installation.
Qu k installation guideic
- Pencil
- Drill
- Tape Measure
- Wire cutter
- Philips-head screwdriver
- Sandpaper
Tools needed for installation
STEP 1
Trace along the inclusive template. Cut along the traced line using a
drywall saw or rotary drill. A simple, inexpensive drywall saw (about
$10 at your local hardware store) is the best choice for beginners.
Caution: This is the most important part of the entire installation.
If you are not certain whether any obstructions exist behind the
desired mounting area, you should start by cutting a small hole in
the center of your penciled mounting hole with a drywall saw. Use a
piece of sandpaper to sand down the cut out edge for a smoother
contour. (See Diagram 1 and Diagram 2)
STEP 2
Run the cable into the cut out location while leaving an extra two
feet to make the connection to the speaker easier. Strip back
approximately ½” of the speaker cable insulation and twist
the copper wires tightly for easy insertion.
On the back of the speaker, press down on the gold-plated
compression terminal to reveal the "eye" and insert the speaker
cable through the eye for secure connection. Release the compres-
sion terminal to lock each cable securely.
Diagram 1:
Cutout tracing
Diagram 2:
Cut Out
To determine the length and the gauge of speaker wire, you will need to
measure the distance between your receiver/amplifier and the speakers.
- Always buy more than you think you would need.
- Equal wire lengths should always be used to maintain an equal
balance in sound volume.
- Sound quality is lost when using thin wire gauge over a long
distance.
- Utility knife
- Safety eyewear
- Gloves
Speaker wire
- - - - - - - - - - - - - - -
- Measure the distance from the receiver/amplifier to the speakers.
-----------------
----------------
-----------------
-----------------
----------------
-----------------
STEP 3
Tighten the dog-ear brackets by simply turning the screws on the
slowly clockwise. The quick-turn mounting system and frame will
"sandwich" or clamp around the wall to hold the speaker securely in
place. (See Diagram 3)
Diagram 3:
Mounting Dog Ear
Closed
Loose
Closed
Loose
..... ......
..
.
.
.
.
.
......
.
dog ear
STEP 4
Screw Screw
Tighten the four mounting screws with the same amount of force until
the speaker is aligned and held securely to the wall surface. Caution:
do not over tighten! (See Diagram 4)
Diagram 4:
Installation
comparable to the speaker’s power handling. Please refer to your owner’s
manual for reference.
(See Diagram 7)
Note: Speaker terminals have corresponding (+) and (-) terminals. It is
important to connect both speakers in phase. Out of phase will result in
thin sound and weak bass. (See Diagram 6)
Diagram 6:
Terminal identification
Warranty & Repair
All OSD A IO r oducts e ( ) year Limited Warranty against d ects in materi s and wo a hip. Proof of pur se must company all cl s. UD speake pr hav 10 ef al rkm ns cha ac aim
Dur h r iod O A O w ti part and correct any d ect in workmanship without char for either parts or l oring t e wa ranty per SD UDI ill replace any defec ve ef ge ab
are not OSD AUDIO’s responsibility.
For this warranty to apply, the unit must be installed and used according to its written instructions. If necessary, repairs must be performed by OSD AUDIO. The unit
must be returned to OSD AUDIO at the owner's expense and with prior written permission. Accidental damage and shipping damage are not considered defects, nor
is damaged resulting from abuse or from servicing performed by an agency or person
OSD AUDIO sells products only through authorized dealers and distributors to ensure that customers obtain proper support and service. Any OSD AUDIO product
purchased from an unauthorized dealer or other source, including retailers, mail over dealers and online sellers will not be honored or serviced under existing OSD
AUDIO warranty policy. Any sale of product by an unauthorized source or other manner not authorized by OSD AUDIO shall void the warranty on the applicable
product.
Damage to or destruction of p ecom on nts due to a c n of e essive power voids the warrppli atio xc anty on those parts. In these cases, repairs will be made on the basis of the retail
value of the parts and b . To return for rla or epair yos, u t e l tomer service at RMA@OSDAUDIO.com for a Returned Merchamus mai cus ndise Authorizat n (RMA) numio ber# then
the unit must be s d to OSD A IO at e s ex se, g with a note explaining the nature of service required. Be sure to pack the speaker(s) in a corrugated hippe UD th owner' pen alon
con iner wita th at le hes of resilient material to protect th uniast 3 inc e t from dama in transit.ge
This Warranty Does Not Cover:
Damage caused by abuse, accident, misuse, negligence, or improper operation (installation) • • Any product whose
identifying number of decal, serial #, etc. has been altered, defaced or removed • Normal wear and maintenance.
+
+
+
-
Next, individually turn each of the
screws that ope te the (Diagram 5) ra
dogears counter clockwise a few turns
until you feel the dogear is loose from
the resting position. Then turn the
scew clockwise until you feel the
dogear makes contact with the wall
surface.
Screw
Screw
Diagram 5:
TIP: Blown-in insulation can some-
times work its way into the moving
components of the speaker and
negatively impacting performance. It
is best to replace about a one square
foot section directly behind the
speaker with rolled-in (bat) insulation.
(See Diagram 5)
S Amplifier ub fer woo
+
Diagram 7:
-
+
+
Power Handling (25 Watts) Minimum
+
-
Note: The speakers wire should be about the same leng . if ht
excess wire behind the wall


Produktspezifikationen

Marke: OSD Audio
Kategorie: Subwoofer
Modell: IWS8

Brauchst du Hilfe?

Wenn Sie Hilfe mit OSD Audio IWS8 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Subwoofer OSD Audio

Bedienungsanleitung Subwoofer

Neueste Bedienungsanleitung fĂĽr -Kategorien-