Orvis Rocky Mountain Bedienungsanleitung
Orvis
Angelrolle
Rocky Mountain
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Orvis Rocky Mountain (2 Seiten) in der Kategorie Angelrolle. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
THE ORVIS COMPANY | MANCHESTER VERMONT 05254 | www.orvis.com
Orvis Technical Questions: info@orvis.com or 800-778-4778
INTRODUCTION
The Rocky Mountain Turbine is built with a new, die-cast
aluminum spool and frame around our famous Battenkill-style drag,
with an offset system to give you the stopping power you need
for big fish, combined with a lighter weight for optimum balance on
your fly rod. The ultra large arbor holds more backing and gets big
fish on the reel faster.
Features include:
• Ultra large-arbor performance
• Die-cast aluminum spool and frame
• Baked enamel finish for long term durability
• Easy conversion from LH to RH retrieve
DRAG OPERATION
The wide-range Rocky Mountain Turbine drag sys-
tem provides a smooth stopping force. Turn the knob
clockwise to increase pressure; turn it counterclockwise
to decrease pressure. The minimum drag setting should
never be less than the pressure required to prevent
over-running of the line on fast runs. Additional drag
may be applied by palming the spool rim with your
fingertips or palm.
SPOOL REMOVAL
The spool release is located in the middle of the reel spool (part
#25). To remove, depress the spool release latch while simultaneously
lifting the spool out of the reel body.
RETRIEVAL CONVERSION
Direction of the retrieve can easily be changed as follows:
1. Remove the retaining screws and the cover plate (parts #14
and #15).
2. Slide the one-way gear (part #27) off the spindle (part #28),
flip it over, then slide the gear back down over the spindle.
3. Replace the cover plate and screws, and the reel is now set for
your preferred retrieve.
OPTIONAL SILENT OPERATION
The Rocky Mountain Turbine’s line-out click sound can be
silenced as follows:
1. Remove the retaining screws and the cover plate (see Cover
Plate Removal and Refitting). (parts #14 and #15).
2. Push the clicker pawl backwards out of engagement. The pawl
will click into the “silent” position. (part # 30).
3. Replace the cover plate and screws, and the reel is now set for
silent line-out.
ROUTINE MAINTENANCE
Your new Rocky Mountain Turbine Reel has been properly lubri-
cated before it was shipped to you. However, it should be cleaned
and lubricated after extensive use or after contact with dirt or sand.
In addition, your reel should receive routine cleaning and lubricating
twice each year.
Lightly lubricate all moving components—handles, center spindle,
and gear shaft with Penn Reel Lube, available in tackle shops. After
lubrication, check screws for proper tightness.
NOTE: The Rocky Mountain Turbine is not ideally suited for salt
or brackish water. Do not put the reel away wet, or into a wet reel
case or tackle box. The finish may be damaged. For extended storage,
remove both line and backing, and loosen the drag.
GUARANTEE
Your Rocky Mountain Turbine reel is unconditionally guaranteed
against defects in materials and workmanship.
If you have any problems, simply send your reel and a $10 check
to the following address:
By USPS Mail: Orvis; Overhaul Services; 178 Conservation Way;
Sunderland, VT 05250.
By FedEx or UPS: Orvis; Overhaul Services; 4182 Main St.;
Manchester, VT 05254.
If the reel is in any way defective in materials or workmanship,
your $10 repair check will be returned to you at once.
Your reel will be completely serviced (cleaned, lubricated, and
returned to you postpaid) for a fee of $10, plus cost of parts.
Damaged reels can be repaired on an individual basis and repair
work will be billed at the hourly shop rate, plus parts. We will
provide a written estimate upon receipt of the reel prior to any
work being done.
QUESTIONS?
If you have any questions about the operation and maintenance of
your new reel, Orvis Technical Advisors are always available.
Email: info@orvis.com. Phone: 1-800-778-4778.
Rocky Mountain Turbine Reel
A
_+
3WF 100
WF4 75
WF5 50 150
WF6 125
WF7 100 225
WF8 200
WF9 175
THE ORVIS COMPANY | MANCHESTER VERMONT 05254 | www.orvis.com
Orvis Technical Questions: info@orvis.com or 800-778-4778
Rocky Mountain Turbine Reel
REEL ASSEMBLY
1 Retaining Screw
2 Drag Adjustment Nut
3 O-Ring
4 Drag Disc
5 Spring Retainer
6 Drag Gear
7 Drag Spindle
8 Drag Knob
9 Spring Washer
10 Drag Knob Stop
11 Spring Retainer
12 Click Pawl
13 Click Pawl Spring
14 Body Assembly
15 Spool Assembly
16 Quick-Release Lever
17 Oiler Pad
18 Quick-Release Cover
19 Quick-Release Spring
20 Cover Screws
21 Handle Knob
22 Handle Spacer
123 4 5 6 7
8
9
10
11 12 11 13
15
14
16 17
18 19 20
26
25
24
23
22
21
32
31
30 19 29
27
28
Rocky Mountain Turbine Fly Reel Specifications
II Reel | weight: 5.8 oz. | 3 inches½
III Reel | weight: 6.3 oz. | 358 inches
IV Reel | weight: 7.4 oz. | 3
1516 inches
Capacity in Yards
All capacities are quoted using 20-lb Dacron® backing.
II III IV
LINE WEIGHT
ROCKY MOUNTAIN TURBINE REEL
Capacity Chart
Produktspezifikationen
| Marke: | Orvis |
| Kategorie: | Angelrolle |
| Modell: | Rocky Mountain |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Orvis Rocky Mountain benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Angelrolle Orvis
2 September 2024
Bedienungsanleitung Angelrolle
- Angelrolle Crivit
- Angelrolle Shimano
- Angelrolle Quantum
- Angelrolle Avet
- Angelrolle Shakespeare
- Angelrolle Zebco
- Angelrolle Redington
- Angelrolle Precision
- Angelrolle Fin-Nor
Neueste Bedienungsanleitung für -Kategorien-
6 Oktober 2024
5 Oktober 2024
4 Oktober 2024
29 September 2024
22 September 2024
17 September 2024
16 September 2024
9 September 2024
8 September 2024
2 September 2024