On-Q lyriQ Bedienungsanleitung

On-Q Hi-Fi-Anlage lyriQ

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für On-Q lyriQ (9 Seiten) in der Kategorie Hi-Fi-Anlage. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/9

301 Fulling Mill Road, Suite G

Middletown, PA 17057

Phone (800) 321-2343 / Fax (717) 702-2546

www.onqlegrand.com

Page 1 of 9

INSTRUCTION/INSTALLATION SHEET

lyriQ™ High Performance Keypad

IS-0369 REV. E



1. Introduction

The lyriQ™ High Performance Keypad, P/N AU1000-xx (see Figure 1), is an

integral part of the lyriQ™ Multi-Room Audio System. It is a component which,

when combined with other essential components ( a Source Input Unit,

Distribution Module and Speakers) and your source equipment (receiver, CD

player, etc.), creates a versatile whole-house audio system that will fill your

rooms with high-quality sound for years to come. It uses Category 5 wiring to

distribute audio signals, control information and IR for remote control. The High

Performance Keypad has on-board 20 Watt per channel class D amplifiers to

provide a rich level of clean sound even in outdoor or large room applications.

It also contains a full set of features, including the ability to control all other

keypad volume controls in the house. Build a system that accommodates the

needs of any space by combining the lyriQ™ High Performance Keypad with

the lyriQ™ Standard Keypad (P/N AU7394-xx) in the same system. The

AU1000-xx is available in white (-WH), light almond (-LA), ivory (-IV), or black

(-BK).

2. Description

The front panel of the lyriQ™ High Performance Keypad, PN AU1000-xx (see

Figure 1), looks almost identical to the lyriQ™ Standard Keypad (AU7394-xx). It

also has push buttons for VOLUME UP/DOWN (with five associated green

Volume Bar Graph LEDs), SOURCE (with four green Source Selection LEDs)

and MUTE (with one red status LED). There is also an IR target window and tri-

colored status LED. The visual cue from the front panel that this is a High

Performance Volume Control are the parenthesis surrounding the music note in

the lower right hand corner.

NOTE: lyriQ™ Keypads are recommended for indoor use only.

On the rear of the lyriQ™ High Performance Keypad (see Figure 2) the Category

5 connection is an RJ45 jack (J1). The TB2 speaker output connections (left and

right, plus and minus) are spring loaded and designed to support up to 14 gauge

wire. The TB3 Line Out connections (plus and minus) are also spring loaded and

designed to support up to 14 gauge wire. This mono-summed output is designed

for powered sub-woofers and as such is filtered through an 80Hz low pass filter.

The other terminal block on the rear (TB1) is used for powering the keypad. Up to

14 gauge speaker wire may be used for this purpose, and this speaker wire (two

conductor or four conductor) is run from a power distribution module (P/N

AU1001) in the enclosure to the ketpad. We recommend 16/4 speaker wire,

since it is available paired with Category 5 from a variety of sources. Again, the

TB1 connections are spring loaded (plus and minus) with the two plus

connections on the red portion of TB1 and the two minus connections on the

black portion of TB1. For ease of installation, connect the red wire and white wire

to the red (plus) portion of TB1 and the black and green wire to the black (minus)

portion of TB1.

Figure 1

Figure 2

301 Fulling Mill Road, Suite G

Middletown, PA 17057

Phone (800) 321-2343 / Fax (717) 702-2546

www.onqlegrand.com

Page 2 of 9

INSTRUCTION/INSTALLATION SHEET

lyriQ™ High Performance Keypad

IS-0369 REV. E



3. Installation

Installation of the lyriQ™ High Performance Keypad is best accomplished at multiple times during new

construction, at “Rough-in” before the drywall is installed, and at “Trim-out” after the drywall is installed and

painted.

NOTE: Before connecting the keypads: Make sure that power supplies are not connected to the lyriQ™

Audio and Power Distribution Modules. For instructions on pre-wiring and installing other components of

the lyriQ™ Audio System, please see the Instruction Sheets included with those components.

NOTE: Always follow TIA-570-B wiring standards for installing and terminating Category 5 cable. Failure to

follow the correct wiring standard could result in damaged equipment and/or electrical interference issues.

NOTE: Maintain a minimum 12” separation between Category 5 cable and any 120VAC cabling.

A. “Rough-in” steps:

1) A single Category 5 cable and 16/4 speaker wire should be run from the enclosure location to a single

gang outlet box or mud ring at each Volume Control location.

B. “Trim-out” steps:

1) Connect the volume control by terminating the pre-wired Category 5 cable from the enclosure with an

RJ45 plug, following the T568A wiring standard and insert this plug into jack J1 (see Figure 2).

2) For the power connection (TB1) strip 3/8” of insulation from each of the four conductors and insert the

red and white wires into the red (plus) portion of TB1. Insert the stripped black and green wires into the

black (minus) portion of TB1 (see Figure 2).

NOTE: The two red connections are tied together, as are the two black connections. They are

provided in pairs to provide flexibility of wiring.

NOTE: Electricians may prefer to think of the black and red wires as plus and the green and white

wires as minus. That wiring will also work, as long as it is also followed at the other end of the cable

(at the Power Distribution Module in the enclosure).

3) Speaker/Line Out/Sub-Woofer connections (see Figure 2):

NOTE: Polarity and channels are clearly marked (L+, L-, R-, R+) for proper identification during

installation.

a) Use TB2 to connect one pair (only) of 8 ohm evōQ™ audio speakers to the volume control.

b) Use TB3 to connect your evōQ™ powered sub-woofer or an external amplifier to the volume control.

These connection terminals do not provide any amplification but the volume control on the keypad

controls the output level of this connection.

4) Connections in the enclosure (see Figure 3):

301 Fulling Mill Road, Suite G

Middletown, PA 17057

Phone (800) 321-2343 / Fax (717) 702-2546

www.onqlegrand.com

Page 3 of 9

INSTRUCTION/INSTALLATION SHEET

lyriQ™ High Performance Keypad

IS-0369 REV. E



a) The Category 5 cable that was run to each keypad location should be terminated with an RJ45 plug

according to the T568A wiring standard and inserted into one of the zone output jacks of the associated

lyriQ™ audio distribution module.

b) For the 16/4 speaker wire power cable that was run to each volume control location, strip 3/8” of

insulation from each of the four conductors and insert the red and white wires into the red (plus ) portion

of TB1. Insert the stripped black and green wires into the black (minus) portion of TB1

NOTE: As noted before, Electricians may prefer to think of the black and red wires as plus and the

green and white wires as minus. That wiring will also work, as long as it is also followed at each

end of the cable.

c) To connect more than eight (8) Keypads to a 4 Source 8 Zone Module, cascade Single Source Modules.

To cascade a Single Source Module, simply run a Cat 5e jumper from any Zone port RJ45 jack on the

front panel of the Multi-source Module he front panel of a Single Source to the “Source In” RJ45 jack on t

Module (see Figure 4).

Figure 3

Produktspezifikationen

Marke:	On-Q
Kategorie:	Hi-Fi-Anlage
Modell:	lyriQ

Brauchst du Hilfe?

Wenn Sie Hilfe mit On-Q lyriQ benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Hi-Fi-Anlage On-Q

On-Q lyriQ Bedienungsanleitung

21 August 2024

Bedienungsanleitung Hi-Fi-Anlage

Neueste Bedienungsanleitung für -Kategorien-

Lenco MC-129 MP3 Bedienungsanleitung

16 Oktober 2024

Akai EIE Pro Bedienungsanleitung

14 Oktober 2024

Sennheiser SZI 1029 Bedienungsanleitung

7 Oktober 2024

Yamaha MusicCast SRT-1500 Bedienungsanleitung

7 Oktober 2024

Kicker 46HDTPH Bedienungsanleitung

7 Oktober 2024

Vtech V-Kids Bedienungsanleitung

5 Oktober 2024

Hitachi AX-M10E Bedienungsanleitung

5 Oktober 2024

IDance XD8N Bedienungsanleitung

5 Oktober 2024

LD Systems DAVE 18 G3 Bedienungsanleitung

4 Oktober 2024

Pyle Pro PWMA1216BM Bedienungsanleitung

4 Oktober 2024