Oliveri DZ122 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Oliveri DZ122 (4 Seiten) in der Kategorie Waschbecken. Dieser Bedienungsanleitung war für 14 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
INSTALLER - PLEASE READ & FOLLOW
THESE INSTALLATION INSTRUCTIONS
Please retain for consumer as care instructions are included
EQUIPMENT REQUIRED for installing your top mount sink: Sonetto
MATERIALS FOR CUTTING COUNTER/BENCHTOP:
Template for your particular model sink and mounting method (may be inside or printed
on carton depending on model). If not available, the sink itself may be used.
Marker such as a pencil or similar for tracing the template onto the counter/benchtop
Tape measure
Drill with 12mm / ½” diameter bit or larger (wood counter/benchtop)
Cutting Device (such as a jigsaw) with suitable blade for counter/benchtop material
Suitable protection such as gloves and goggles to be used while drilling or cutting
MATERIALS FOR FITTING THE TOP MOUNT SINK:
Sonetto sink dered) (with correct tap holes as or - includes mounting clips, sealing
gasket, model). basket wastes and other accessories (depending on
These Installation Instructions
Level sto check counter/benchtop & sink i installed level
Phillips head screwdriver mounting clips)(#2 to tighten
Flat head screwdriver (large - to tighten basket wastes)
Suitable sealant (neutral-cure silicone sealant or equivalent)
Masking material ss sealantto protect counter/benchtop and sink from exce
Additional Mounting Hardware clamps cluded withif fitting into thinner material. The in
the sink require a minimum counter/benchtop thickness of 25mm / 1”.
CHECK MODEL & TAP HOLES
The model number on the sink
packaging must match the model
of sink the customer ordered.
Check the number and position of
tap holes is correct.
Do not install if incorrect.
CHECK THE CONDITION
Inspect the sink for any visible
defects. Do not install the sink if
defects are found. Contact your
sink retailer / point of purchase.
AVOID CUTS
The perimeter and punch-outs on
the sink may contain sharp edges.
Handle the sink carefully to avoid
personal injury.
AVOID SCRATCHES
Polished stainless steel can be
scratched if proper care is not
taken during installation.
Topmount sinks may also be know as “drop in” or “inset” sinks. n
Sink models w
ith prefix MO, PE, UF, DU, LR, EF, NP, MR, SI & RR.
These sinks will fi
t into standard 600mm bench tops.
Templates su
pplied are to assist in achieving th for top mounting the sink.e correct shape hole
Careful use of the templ
ate is required to achieve the correc cutout shape. the template not available, the cut out t If is
shap carefullye may be created by
inverting the sink onto the counter/benchtop d tracing ar an ound the perimeter. Cut
the hole 10mm inside the traced line.
Many Sonetto sinks have waste outlets positi he sink is correctlyoned to the rear of the bowls. Ensure t positioned when
fitting.
Unequal bowl depth:
Sinks that combine different sized bowls may also have unequal bow Waste plumbing l depth. will need to
accommodate this variance. MO, PE, NP, SI & RR sinks have a height adaptor included with the sink where needed.
Models UF03D & UF
04D have a 60mm height difference in waste connections for the main and smaller bowl. Waste
plumbing will need to accommodate this va
riance.
Models UF05D & UF
06D have a 35mm height difference in waste connections for the main and smaller bowl. Waste
plumbing will need to accommodate this va
riance.
EF emodels have a 35mm h
ight difference in waste connecti for the main and smaller bowl. Waste plumbi ons ng will
need to accommodate this
variance.
MANHATTAN & DAL
LAS (MH or DA)
THESE SINKS WILL NOT FIT IN
A STANDARD 600MM COUNTER/BENCH TOP.
Measure carefully to
ensure sufficient room exists (including allowance for a splashback if required). The cutout
shape may be created by carefully
inverting the sink onto the counter/benchtop d tracing ar an ound the perimeter. Cut
the hole 10mm inside the traced line.
FOR “TOP MOUNT’ OR “DROP IN” SINKS
NORTH AMERICA DISTRIBUTORS
Andrew Sheret LTD
7434 Edmonds St, Wholesale
Counter, Burnaby, BC V3N 1A8,
Canada
Phone: 604-521-0788
Mega Western Sales LLC
6861 Walker St, La Palma,
CA 90623, USA
Phone: 310-323-7900 Any advice, recommendation, information, assistance or service provided by Tasman Sinkware in
relation to goods manufactured by it or their use and installation, is given in good faith and is believed by
Tasman Sinkware to be appropriate and reliable. However, any advice, recommendation, information,
assistance or service is provided by Tasman Sinkware without responsibility or liability.
SPECIAL INSTRUCTIONS FOR PARTICULAR TOP MOUNT SINK MODELS
CAUTION
Leave protective tape on the sink when inverting over a benchtop and tracing its shape.
The polished stainless steel will scratch if the sink slides across a hard surface.
© Tasman Sinkware 2006
AU Top Mount Installation Instructions
TF 08d.doc
Tasman Sinkware
is a division of
Fletcher Building
AUSTRALIA
HeadOff e&ic
Manufacturing Plant
Tasman Sinkware Pty Ltd
Regency Park SA
Phone: +61 8 8348 6444
Fax: +61 8 8348 6495
Email:
sinkware@tasbuildpro.com.au
www. .comsonettosinks
Tasman Sinkware
is a division of
Fletcher Building
TEMPLATE *
A number of sinks require a non shape hole (not a Sonetto -standard
rectangle inted or circle). Locate the template included in (or pr on) the
packaging and place in the correct position on the co unter/benchtop.
Compare the template to the sink to check it is co sink templates rrect. Some
apply to both left-hand and right-hand model sin ks. Ensure the template is
the correct way around for your model sink. (If no template is available,
carefully invert the sink over the counter/benchtop and trace around it.)
CHECK SPACE & LEVEL
Use a level to check the counter/benchtop – if not level, have rectified.
Ensure there is adequate space for tapware (including a splash back if
specified). Check space for installation (underneath) and operation (above).
Particular care must be taken when a thick splash back is used (it may
interfere with tapware location and operation). Ensure the cabinet will not
foul the sink mounting flange or basins.
MARK CUT OUT *
Carefully mark around the cardboard template (or follow drawing instructions).
Once the hole is marked out, use the template to conduct a final check before
cutting. Note: The template is the exact finished cut-out size required.
IMPORTANT
If you have traced the sink itself to mark your cut out, the hole must be
cut 10mm inside the marked line.
CUT & FINISH HOLE *
Re-check the position and cut out shape you have traced before cutting.
Ensure there are no obstacles below that might interfere with cutting.
Drill pilot holes to accept an appropriate cutting tool for the counter/benchtop
material (wear suitable personal protection equipment). Cut just inside the
template mark (or 10mm inside the sink tracing).
TRIAL FIT THE SINK
Check that all clips are folded in so they will adequately clear the cut-out.
Carefully position the sink into the cut-out to make sure it fits correctly.
If the fit is not correct, remove the sink and proceed with remedial work.
Perform another trial fit after corrections have been made.
MASKING
If using a sealant, masking is necessary to prevent sealant overrun.
It is recommended that the edge of the sink and the edge of the cutout are
both covered with a suitable masking tape.
This tape should be removed within 2 days of application.
CHECK FOAM SEAL
Make sure the foam seal is intact and fits all the way around the sink with no
gaps visible. This will ensure a watertight seal when the sink is properly
tightened down to the counter/benchtop.
ADDITIONAL SEALANT
Apply additional sealant / caulking compound around the join where the
counter/benchtop and the stainless steel sink meet. Check that the caulking
product is mildew resistant and is suitable for use on the counter/benchtop
material and also is suitable for use on stainless steel. Clean away any
excess before it dries. Note: Additional sealant should always be used if gaps
are apparent after the sink has been clamped to the counter/benchtop.
PLUMBING & TAPWARE
IMPORTANT - Connections to plumbing should always be done by a
licensed plumber. Fit supplied basket wastes to sink bowls. Some models do
not include basket wastes for every bowl. Install tapware according to
manufacturer’s instructions.
Care should be taken when fitting wastes to the sink. Follow the instructions
provided with the wastes.
INSTRUCTIONS CONTINUE OVER PAGE
It is essential that the installation is waterproof and carried out in accordance with these instructions.
Tasman Sinkware will not be held responsible for any damage caused by leakage or faulty installation.
CARE INSTRUCTIONS FOR YOUR STAINLESS STEEL SINK SONETTO
AVOID CONTACT WITH ROUGH OR DIRTY SURFACES as new polished stainless steel will show scratches!
DO’s
• •Clean with soap & water (towel dry) Clean along the grain of the Stainless Steel
• •Use a soft brush or sponge (old tooth brush) Wipe over with a glass cleaner (Windex is very good)
• •Polish with a metal polish paste (Autosol / Brasso) Use a Liquid cleaner (Bon-Ami or Jiff)
Use a granulated stainless steel cleaner (Essteele)
DO NOT’s
NEVER use Steel wool
Beware of harsh liquid cleaners
Beware of grit within cloths and mineral deposits within water
Avoid prolonged exposure to acids from Fruit, Fruit juices, Salts, Spirits, Bleach, Tea-bags
Avoid prolonged contact with ordinary steel which can rust Tin Cans, Steelwool
Do not keep harsh (acids or chlorine) chemicals under sink / laundry tub
Do not leave on stainless steel surfacechlorine/chloride chemicals
Do not leave on stainless steelliquid soaps & cleaners to dry
Do not use bleaches (White King, Domestos, Clorox)
FITTING THE SINK
If you choose to mount the tap / faucet onto the sink prior to fitting, take extra
care as it will change the weight and balance of the sink. Position and align
the sink correctly in the cutout and lower it onto the counter/benchtop. From
underneath, tighten the clips with a screwdriver (follow the sequence marked
on the template) until the sink is secure and no gaps are visible. Take extra
care if usin
g
power tools as ove
r
-ti
g
htenin
g
can dama
g
e clips.
FINAL CHECK OF FOAM SEAL
With the sink tightened down. Visually confirm the foam seal is not protruding
anywhere underneath. If it does, undo all the clips, reposition the foam seal
and tighten down again. If the foam seal has been damaged, replace the
damaged section. If the tap/faucet was mounted prior to fitting – check that
the position is correct.
FOLLOW THESE STEPS TO INSTALL THE SONETTO TOP MOUNT SINK
IF COUNTER / BENCHTOP IS SUPPLIED WITH SINK HOLE ALREADY CUT OUT, SKIP STEPS MARKED WITH *


Produktspezifikationen

Marke: Oliveri
Kategorie: Waschbecken
Modell: DZ122

Brauchst du Hilfe?

Wenn Sie Hilfe mit Oliveri DZ122 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Waschbecken Oliveri

Bedienungsanleitung Waschbecken

Neueste Bedienungsanleitung für -Kategorien-