Nova VisionNOVA Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Nova VisionNOVA (5 Seiten) in der Kategorie Babyfon. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/5
MICLOW POWER
CH SW
4 3 2 1
POWER
OFF ONIR
7,5–300mA
AV-OUT
SV-1000mA
(CHARGE)
OFFON
AVIN
4
3
2
1
CH SEL
ON
A1 A2 A3
A4
A5
B1
B2
B3
B4
B11 B12 B13 B14
B5
B8 B9 B10
B6B7
A6
A7
A8
A9 A10 A11
Technical specifications
Camera Monitor
Camera
Frequency: 2.4 GHz
Channel: 4 selectable channels
Modulation: FM
Antenna: Built-in omni-directional antenna
Image sensor: 1/3” CMOS color image sensor
Output power (max.): 10 mW (CE)
Power consumption (max.): 1.8 Watts
Power supply (optional): 230VAC to 7.5VDC, 300mA
or 3 x AA Battery
Operational range: Up to 100 meters
(open air situation)
Dimension: 75mm x 45mm x105mm
Weight: 135g
Monitor
Frequency: 2.4 GHz
Channel: 4 selectable channels
Receiver sensitivity: -80dBm
Antenna: Built-in omni-directional antenna
Power consumption (max.): 5 Watts
Power supply: 100~240VAC to 5VDC, 1A
or 3,6V 1400mAh LI-ION recharge-
able battery
Dimension: 140mm x 115mm x 45mm
Weight: 245g
VisionNOVA omslag 04-07-06 15:11 Side 1
We thank you for choosing VisionNOVA Video Babycall, and we know
you'll be pleased with your choice. Please read this manual carefully
and keep it for future reference.
The box includes
• One camera
• One monitor with an LI-ION battery installed
• One AV (audio/video) cable
• Two power adapters (7.5V DC for the camera and 5V DC for
the monitor)
• This user manual
Power supply
The camera can be used with a power
adapter or three batteries (type AA alkaline).
On battery power the camera will normally
work up to 11 hours.
Using the power adapter
Plug the power adapter labelled OUTPUT:
7.5V DC into a wall outlet and plug the adap-
ter plug into the underside of the camera (A9).
Put the ON/OFF switch (A11) in ON position.
Using batteries
Open the cover of the battery compartment
(A8) on the rear of the camera.
Insert three AA batteries so their plus (+) and
minus (-) ends are facing as shown on the
inside of the battery compartment cover and
close the battery compartment securely.
Move the ON/OFF switch (A11) to the ON
position.
Discard used batteries in an environmentally
friendly and responsible way.
Never mix old and new batteries.
Remove the batteries from the camera if you
are not planning to use it for a period of time.
Channel selection
Always select the same channel (A10) for the
camera and the monitor.
Congratulations! Camera: Connections
Camera: Legend
Monitor: Legend
MM MM
A1 Lens
A2 Lens knob
A3 Lens body: rotates up to 120
degrees vertically
A4 6 IR LEDs: provide infrared
light for night vision
A5 Microphone
A6 LED indicator for low battery
power
A7 Mounting holes for fixing to
wall etc., centre to centre
distance 33 mm
A8 Battery compartment
A9 7.5V power adapter plug
A10 Switch for channel selection
A11 ON/OFF switch and night
vision switch
B1 Flip-down 2.5” TFT-LCD dis-
play
B2 Speaker
B3 Alarm ON/OFF button
B4 LED indicator for alarm
B5 LED indicator for charging
B6 LED indicator for fully
charged battery
B7 LED indicator for low battery
power
B8 Jack for audio/video output
B9 Volume controller
B10 Brightness controller
B11 Channel selector
B12 Reserve
B13 Power ON/OFF switch
B14 5V power adapter plug
CH SW
4 3 2 1
POWER
OFFONIR
7,5–300mA
POWER
OFF ON IR
MM
M
1
Fine tuning
Place the camera in a suitable location and
point the lens (A1) toward the observation area
by rotating the lens body (A3) vertically.
Adjust the focus by turning the lens knob (A2)
until the image is sharp.
Night vision
The camera has six infrared LEDs (A4) that give
you clear images in the dark. To activate the
infrared function, move the switch (A11) to the IR
position.
When using the night vision function, the picture
automatically goes into black and white mode.
The night vision function is disabled when
running on battery power.
Low battery power indicator
The LED indicator for low battery power (A6)
lights up when the batteries need to be replaced.
Power supply
The monitor can run on the power adapter and
the pre-installed LI-ION rechargeable battery.
Charging time is 1 to 4 hours, whether the
monitor is off or on. When the monitor is turned
off and the charging is completed, the indicator
for fully charged battery (B6) lights up. The bat-
tery will work approximately 6 hours with the
monitor flipped down and 2 to 3 hours with the
monitor open.
Using the power adapter
Plug the power adapter labelled OUTPUT: 5V
DC into a wall socket and plug the adapter
plug into the rear of the monitor (B14).
Move the ON/OFF switch (B13) to the ON
position
.
Adjust the volume (B9) to the desired level.
Adjust the brightness (B10) to the desired level.
Channel selection
Only one switch (B11) must be moved to the
ON position.
Select Channel 1 by moving CH SEL 1 to ON
Select Channel 2 by moving CH SEL 2 to ON
Select Channel 3 by moving CH SEL 3 to ON
Select Channel 4 by moving CH SEL 4 to ON
Check that you select the same channel as on
your camera.
POWER
OFF ON IR
LOW POWER
Monitor: Connections
MMMM
SV-1000mA
(CHARGE)
OFFON
AVIN
4
3
2
1
CH SEL
ON
SV-1000mA
(CHARGE)
OFFON
AVIN
3
2
1
CH SEL
AV-OUT
AV-OUT
AVIN
4
3
2
1
CH SEL
ON
M
MMMM M
Produktspezifikationen
| Marke: | Nova |
| Kategorie: | Babyfon |
| Modell: | VisionNOVA |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Nova VisionNOVA benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Babyfon Nova
6 Mai 2023
6 Mai 2023
6 Mai 2023
6 Mai 2023
6 Mai 2023
6 Mai 2023
6 Mai 2023
6 Mai 2023
6 Mai 2023
6 Mai 2023
Bedienungsanleitung Babyfon
Neueste Bedienungsanleitung für -Kategorien-
8 Mai 2023