NAV-TV NTV-KIT997 Bedienungsanleitung

NAV-TV Empfänger NTV-KIT997

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für NAV-TV NTV-KIT997 (11 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/11
AUDI VW Porsche / Bentley M.O.S.T. 150 to 12-channel Analog & Digital / /
sound processor with OBD Programmer NTV-KIT997
3950 NW 120th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760
TY
12/28/21
NTV-DOC314C
2 | P a g e
ZEN-V Compatibility
Th NAV- -V proce seamlessly converts lat model AUDI, VW, Porsche & Bent factory MOST-1e TV ZEN ssor e ley 50
audio bus to -channel analog and TOSLink output. Adding aftermarket amplifiers to the OE MIB, MIB2, 12 RCA
MIB2.5 or PCM4, PCM4.1 PCM5.0 system has never been so simple. This kit integrates with, MIB3 , and PCM6
the OEM M.O.S.T.® bus to retain volume control, full fade and balance, treble, mid-range, bass (analog only)
control & Bluetooth calls with no external speaker (true OEM integration). voice NOTE: OEM radio systems not
equipped with amplifier or fiber must be flashed with the VAG-COMM or NAV- -V-PRG (NTV-KIT861, an TV’s ZEN
sold separately) prior to installation. Vehicles equipped with OEM amplifier do not need to be flashed. an
Cars with the MIB3 system require our OBD programmer, regardless of whether they have an Amp or not.
ZEN-V overview
(MIB, MIB2, MIB2.5
MIB3 or PCM4, 4.1,
5.0 radio only) or 6
Kit Content
Year(s)
Make
Model
2015+
AUDI
Any model with confirmed MIB, MIB HS (A3, TT, etc.)2, MIB3 or MIB
2017+
AUDI
A3, A4, A5, A6, A7, A8, Q5, S3, S4, S5, S6, S7, S8, TT Q7, SQ5, , e-tron
2017+
Porsche
911, Boxster, Cayenne, Cayman, Macan, Panamera
2017+
Bentley
Bentayga
2016+
VW
ANY model with MIB, MIB2 or MIB-H, MIB3 S
Power
connector
USB (updates)
MOST 150 fiber input
--FUTURE USE --
Analog RCA outputs
WARNING: Do not connect any RCA cables to the ZEN-V interface or
additional processors prior to properly grounding aftermarket amplifier(s)!
DIP switches
Status LED
--FUTURE USE --
Overview
ZEN M Fiber OST
NTV-CAB134
USB Cable (updates)
NTV-CAB009
ZEN Power Harness
NTV-HAR316
EN RC Harness Z A
NTV-HAR315 ZEN-V Interface
NTV-ASY272
ZEN MIB3
Programmer
NTV-KIT996
TY
12/28/21
NTV-DOC314C
3 | P a g e
Wire Side
AUDI
Bentley
Bentayga
Porsche or
Audi MIB3
See Below
VW
ZEN-V Installation
1. If this vehicle has factory amplifier, it must be removed and the -V can be installed into its place.a ZEN If
this is an MIB3 system, then the Zen is installed at the MMI module and the amp remains connected.
If this vehicle is not amplified from factory, install the -V behind the radio.ZEN
2. Connect the following wires from the
provided :power harness
*This remote wire must be used for aftermarket amplifier remote for proper functionality. A relay should be used
for reliable turn-on (500mA max).
3. Before connecting power to the ZEN-V,
adjust dip-switch settings for the desired options:
4. If using analog RCAs for signal to the amplifier, connect according to the reference chart below.
WARNING: Do not connect RCA cables to this interface until all amplifiers/external processors are
properly grounded. Failure to do this may cause damage to the interface and VOID the warranty!
1
2
3
4
5
6
7
8
9
10
11
12
Left
Front
Right
Front
Left
Front
Right
Front
Left
Front
Right
Front
Left Rear
Door
Right Rear
Door
Left Rear
Center
Right Rear
Center
Center
Sub
5. If using TOSLink for signal to the amplifier, connect the cable to the TOSLink port shown on page 2.
NOTE: both Analog and Digital output sound simultaneously, regardless of which type is used.
6. Connect the provided from the MOST Fiber Cable (previously removed) amplifier, or from the radio/
MMI ’s fiber port to the MOST port on the ZEN-V.
ZEN-V pin
Color
To vehicle:
1
Yellow
12v (+) Constant
3
Violet
-- --Reserved, NOT USED
4
Black
Ground (-)
6
Blue
12v (+) remote output*
Time Alignment
Attenuation
TOSLink DownMix
Loudness
Vehicle Settings
Position
DIP 1
DIP 2
DIP 3
DIP 4*
DIP 5
DIP 6
UP
(off)
Front Row
Full Scale
output (0 dB)
DownMix ON
Loudness OFF
DOWN
(on)
Driver Focused
-12 dB output
DownMix OFF
Loudness ON
DIP 5
DIP 6
X
X
DIP 5
DIP 6
X
X
DIP 5
DIP 6
X
X
DIP 5
DIP 6
X
X

Produktspezifikationen

Marke: NAV-TV
Kategorie: Empfänger
Modell: NTV-KIT997

Brauchst du Hilfe?

Wenn Sie Hilfe mit NAV-TV NTV-KIT997 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Empfänger NAV-TV

NAV-TV

NAV-TV NTV-KIT997 Bedienungsanleitung

30 April 2023

Bedienungsanleitung Empfänger

Neueste Bedienungsanleitung für -Kategorien-

Rotel

Rotel RA‑1592MKII Bedienungsanleitung

16 Oktober 2024
Denon

Denon AVR-S900W Bedienungsanleitung

16 Oktober 2024
Pro-Ject

Pro-Ject Amp Box DS2 Bedienungsanleitung

15 Oktober 2024
AKG

AKG HP12U Bedienungsanleitung

15 Oktober 2024
Sennheiser

Sennheiser EM 9046 SU Bedienungsanleitung

14 Oktober 2024
Yamaha

Yamaha MusicCast RX-V481 Bedienungsanleitung

14 Oktober 2024
JL Audio

JL Audio VX600/6i Bedienungsanleitung

12 Oktober 2024
Pioneer

Pioneer SX-303RDS Bedienungsanleitung

10 Oktober 2024
Technics

Technics SA-160L Bedienungsanleitung

8 Oktober 2024
Avantree

Avantree Audiplex Bedienungsanleitung

7 Oktober 2024