Musical Fidelity MX-HPA Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Musical Fidelity MX-HPA (4 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
MX-HPA Fully Balanced Headphone Amplifier
- 1 - Issue 1.1
The ultimate in balanced and single ended headphone listening.
The MX HPA is a very high performance fully balanced headphone amplifier Class A”
in a beautifully designed and executed casework.
unit features two inputs, balanced and single ended. These are separate and an The
input select switch allows choice between separate balanced and single-ended sources.
These inputs accept normal line-level signals of 300mV nominal (suitable for 30mV-
>3V) from a wide range of equipment.
Gain switching is provided to allow boost for higher impedance headphones, so the
unit is compatible with all dynamic headphones regardless of impedance. It is
recommended to use the LOW setting for headphones of 200 ohms or less; the HIGH
setting for headphones over 200 ohms or particularly insensitive headphones.
The front panel XLR/JACK sockets are dual purpose; it is possible to use either one or
two - terminated headphones; pairs of standard 6.25mm ¼” stereo Jack
or
a
single
pair
of headphones, terminated in two three-pin male XLR plugs.
The necessary single ended/ balanced mode switching is carried out automatically on
connection of the headphone(s).
MX-HPA Fully Balanced Headphone Amplifier
- 2 - Issue 1.1
FRONT VIEW
POWER GAIN HEADPHONE OUTPUTS
OFF/STDBY = HIGH (AS SINGLE ENDED STEREO JACKS) VOLUME
ON = LOW OUTPUT 1 OUTPUT 2 CONTROL
INPUT SELECT HEADPHONE OUTPUTS
BALANCED (AS BALANCED HEADPHONE XLRs)
RCA LEFT OUT RIGHT OUT
REAR VIEW
RIGHT INPUTS LEFT
XLR RCA XLR RCA IEC
BALANCED RIGHT ANCED LEFT MAINS BAL
INLET
XLR SOCKET PINOUTS
XLR Balanced input
and output lead
connections:
(for reference only, no
XLR signal leads
supplied)
Pin:
Functions: (line input/output)
Functions: (headphone outputs)
1
Ground (cable shielding)
Ground (not necessarily used)
2
Normal polarity ("hot" or “+”)
Transduc er “+”
3
Inverted polarity ("cold" or “-“)
Transducer “ -
MX-HPA Fully Balanced Headphone Amplifier
- 3 - Issue 1.1
Output
Power 1.8 Watts per channel into 8 Ohms (27dBW)
Maximum output voltage 19 Volts RMS, 20Hz to 20 kHz; onset of clipping
(54 Volts peak- -peak) balanced. to
Line input
THD+N <0.005% typical, 20Hz to 20 kHz
Signal / noise ratio -weighted >120dB ‘A’
Input impedance 50k Ohms
Frequency response +0, 0.1dB, 10Hz to 20 kHz
Gain, LO position (volume max) 18db (8x)
Gain, HI position (volume max) 24dB (15x)
Connections
Line level inputs 1 pair line level XLR (balanced) connectors
1 pairs line level RCA connectors
Headphone outputs 1 pair 3- pin XLR/¼” stereo Jack combined sockets
Power requirement
Mains voltages -250VAC 50-60Hz universal worldwide supply 90
Consumption <0.25 Watts standby (Orange LED lit)
15 Watts maximum (Blue LED lit, full power output)
Weight
Unit only, unboxed (5 lbs) 2.2 kg
In shipping carton kg ( lbs) 3.7
Dimensions
Width 0 mm (8 22 ”)
Height (including feet) 53 mm (2”)
Depth (front to back) inc. terminals 0 mm (9½ 24 ”)
Standard accessories
IEC type mains lead (10-Amp type)
Musical Fidelity reserves the right to make improvements which may result in
specification or feature changes without notice. E+OE.


Produktspezifikationen

Marke: Musical Fidelity
Kategorie: Empfänger
Modell: MX-HPA

Brauchst du Hilfe?

Wenn Sie Hilfe mit Musical Fidelity MX-HPA benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Empfänger Musical Fidelity

Bedienungsanleitung Empfänger

Neueste Bedienungsanleitung für -Kategorien-