Mtx Audio WET75.2 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Mtx Audio WET75.2 (32 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 31 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/32
OWNER’S MANUAL
WET SERIES AMPLIFIERS
M T X . C O M
Use your smartphone to scan or visit
youtube.com/user/MTXAudioUSA
to learn how to properly install this
amplifier.
M T X . C O M
2
PRODUCT INFORMATION
Model #
Serial #
Dealer’s Name
Date of Purchase
INTRODUCTION
Thank you for purchasing this MTX Audio Hi-Performance marine grade amplifier. Proper installation
matched with MTX speakers and subwoofers provide superior sound and performance for endless
hours of enjoyment on your boat wherever the current takes you. Congratulations and enjoy the
ultimate audio experience with MTX!
FEATURES
• Compact Size
• Double Sided PCB
• Surface Mount Components
• MOSFET Design
• LPF and HPF Crossover
• Adjustable Bass Boost
• Noise Free Design
• Short, Thermal, and High/Low Voltage Protection
• Conformal Coated PCB
• Plexiglass Cover for Controls
• Stainless Steel Hardware
• Rubber Gaskets Around RCA Connectors
CONTROL FUNCTIONS
1. Speakers - Connect speakers/subwoofers to these terminals. Be sure to check wire for proper
polarity. Never connect the speaker cables to the chassis ground.
2. +BATT (+12 Volt Power) - Connect this terminal through a FUSE or CIRCUIT BREAKER to the
positive terminal of the vehicle battery or the positive terminal of an isolated audio system
battery. WARNING: Always protect this power cable by installing a fuse or circuit breaker of the
appropriate gauge within 18 inches (45cm) of the battery terminal connection.
3. Remote Turn On - This terminal turns on the amplifier when (+) 12 volt is applied to it. Connect it to
the remote turn on lead of the head unit or signal source.
4. GND - Run an equal gauge wire from the Ground (GND) terminal on the MTX amplifier to the
negative terminal on the battery. Use the shortest distance possible. It is always a good idea to
replace the factory ground at this time with a cable equal or larger than the new amplifier power
cable. CAUTION: Do not connect this terminal directly to the vehicle battery
ground terminal or any other factory ground points.
5. RCA Input Jacks - These RCA input jacks are for use with source units that have RCA outputs. A
source unit with a minimum level of 200mV is required for proper operation. The use of high
quality twisted pair cables is recommended to decrease the possibility of radiated noise entering
the system.
6. Gain Control - The Gain control will match the amplifier’s sensitivity to the source units signal
voltage. The operating range is 5V to 200mV. This is NOT a volume control.NOTE:
M T X . C O M 3
7. Low Pass Filter Control (Mono Block) - This control is used to select the desired low pass x-over
frequency. The frequency can be adjusted from 40Hz to 220Hz for all bass mono models.
8. Subsonic Filter Control (Mono Block) - This control can filter out unwanted low frequency from
20Hz (OFF) to 50Hz. This function should only be used with vented enclosures.
9. Bass Boost Level Switch (Mono Block) - This switch can boost bass level by 0dB, 6dB, or 12dB.
The boost frequency is centered at 50Hz.
10. High Pass Filter (Full Range) - This controls the frequencies played for the front channels. Low
frequencies can be cut off from OFF to 200Hz. At OFF position, no low frequencies cut off,
meaning full range.
11. X-Over Mode and Frequency Control (Full Range) - These controls allow control over the
frequencies played for the rear channels. There is an option for Low Pass, Full Range, or High
Pass. In LP or HP mode, the crossover frequency can be tuned from 50Hz to 750Hz.
12. Power Indicator - This LED will light up when the amplifier is working properly.
13. Protection Indicator - The Red LED will light up and flash if there is a fault presented to the
amplifier. Please disconnect the amplifier and resolve the fault before reconnecting the amplifier.
PANEL LAYOUT
4-Channel Amplifier Panel Layout
1 4
6 13
3
10
2
6 12115


Produktspezifikationen

Marke: Mtx Audio
Kategorie: Empfänger
Modell: WET75.2

Brauchst du Hilfe?

Wenn Sie Hilfe mit Mtx Audio WET75.2 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Empfänger Mtx Audio

Bedienungsanleitung Empfänger

Neueste Bedienungsanleitung für -Kategorien-