Mtx Audio RT604 Bedienungsanleitung

Mtx Audio Empfänger RT604

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Mtx Audio RT604 (44 Seiten) in der Kategorie Empfänger. Dieser Bedienungsanleitung war für 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/44

RT604

4 Channel Class-AB Power Ampliﬁer

360W

RMS

www.mtx.eu.com

www.mtx.com

GNDREM+12V

POWER SPEAKER

FRONT

REAR

BRIDGE

R+

R- L+ L-

LOW INPUTHLI

FR FL

+ R - G - L + GAIN X-OVER LPFHPF

6V 0,1V

40Hz 400Hz

FULL

HPF LPF

FULL

HPF LPF

40Hz 400Hz

40Hz 400Hz 40Hz 400Hz

FR FL

+ R - G - L +

www.mtx.com - www.mtx.eu.com

Owner’s Manual - RT604

Introduction

Thank you for purchasing an MTX Audio Hi-Performance amplier. Proper installation matched with MTX speak-

ers and subwoofers provide superior sound and performance for endless hours of waking the neighbors, slam-

min' your friends or at out stomping wanna-be players. Congrats and enjoy the ultimate audio experience with

MTX !

Specications :

• 4-Channel Class-AB Amplier

• CEA2006 certied Power Output :

- 90 watts RMS x 4-channel at 2 ohm and THD+N ≤1%

- 60 watts RMS x 4-channel at 4 ohm and THD+N ≤1%

- 180 watts RMS x 2-channel at 4 ohm and THD+N ≤1%

• Crossover :

- High pass 12dB/oct variable from 40Hz to 400Hz

- Low pass 12dB/oct variable from 40Hz to 400Hz

• Signal-to-Noise Ratio (1 watt) : > 80dB

• THD+Noise (Distortion) (1 watt) : ≤ 1%

• Frequency Response (±1dB) : 20Hz-30000Hz

• Maximum Input Signal : 6V

• Maximum Sensitivity : 100mV

• Dimensions : 364mm x 180mm x 55mm

• High level inputs

Control Panel

Control Panel :

Gain Control (GAIN) : The gain control matches the input sensitivity of the amplier to the source unit being used.

The operating range varies from 100mv to 6V.

Adjusting the gain

1. Turn the gain control on the amplier all the way down (counter clockwise).

2. Turn up the volume control on the source unit to approximately 3⁄4 of maximum.

3. Adjust the gain control on the amplier until audible distortion occurs.

4. Adjust the gain control down until audible distortion disappears.

5. The amplier is now calibrated to the output of the source unit.

Low-Pass High-Pass X-Over Switch (X-OVER) :

In “LPF” position, the active low pass (LP) x-over is turned on

In “HPF” position, the active high pass (HP) x-over is turned on

In “FULL” position, the x-over is turned o

High Pass X-Over Frequency Control (HPF) :

Used to select the desired high-pass (HP) x-over frequency. The frequency is adjustable from 40Hz to 400Hz..

Low Pass X-Over Frequency Control (LPF) :

Used to select the desired low-pass (LP) x-over frequency. The frequency is adjustable from 40Hz to 400Hz..

RCA Inputs (LOW INPUT) : These RCA inputs are used with source units that have RCA or Line level outputs.

(Source units need a minimum level of 100mV output for proper operation of the amplier).

MTX recommends only high quality twisted pair cables (such as StreetWires) to decrease the possibility of radi-

ated noise entering the system.

PowerOn/Protection LED - The LED illuminates red when the amp is switched on. When the amps is in shortcir-

cuit or thermal protection, the LED is blinking.

Speaker level inputs (HLI) :

This input will allow the amplier to operate from source units with speaker-level outputs. Output speaker leads

from the source unit should be tied directly to the wire harness provided with the amplier.

Note : When speaker level inputs are used, a remote turn on wire must used to switch the amplier on and o.

(+12V) Power Terminal : This is the main power input for the amplier and must be connected directly to the posi-

tive terminal of the vehicles battery for proper operation. Use caution when installing (+12) power cable in the

vehicle. Avoid running this cable parallel with RCA cables, antennas, or other sensitive equipment due to massive

currents that can induce noise into the audio system. It is also very important to have a tight, secure connection

for maximum performance. MTX recommends using 10mm

2 power wire with the MTX RT604 amplier.

Remote Terminal (REM) : The amplier can be turned on by applying 12 volts to this terminal. Typically this volt-

age is supplied by a wire from the source unit marked “remote” or “power antenna”.

Ground Terminal (GND) : A proper ground is required for your amplier to operate at peak performance. A short

ground cable the same diameter as the power cable should be used to attach the ground terminal directly to

the chassis of the vehicle. Always remove paint, dirt or debris to expose bare metal where the ground will be

attached.

Speaker Terminals (SPEAKER) : Connect speakers to these terminals. Observe speaker polarity throughout the

system. Improper phase can result in loss of bass response and/or poor overall sound quality.

Bridge Mode : When bridging the amplier, use the right positive terminal and the left negative terminal only.

Warning : do not bridge the amplier with an impedance lower than 4 ohm.

Fuse (FUSE) : When fuse blow, replace them with the same value. Never use a higher rated fuse !

Caution : fuses are located under the amp.

Produktspezifikationen

Marke:	Mtx Audio
Kategorie:	Empfänger
Modell:	RT604

Brauchst du Hilfe?

Wenn Sie Hilfe mit Mtx Audio RT604 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Empfänger Mtx Audio

Mtx Audio MUD100.4 Bedienungsanleitung

27 August 2024

Mtx Audio XThunder 800.5 Bedienungsanleitung

16 August 2024

Mtx Audio JackHammer JH5001 Bedienungsanleitung

15 August 2024

Mtx Audio XThunder1200.1 Bedienungsanleitung

14 August 2024

Mtx Audio Thunder Sports MUD100.2 Bedienungsanleitung

14 August 2024

Mtx Audio Thunder 1000.1 Bedienungsanleitung

14 August 2024

Mtx Audio Thunder Marine WET500.1 Bedienungsanleitung

14 August 2024

Mtx Audio RT1000-1D Bedienungsanleitung

14 August 2024

Mtx Audio JackHammer JH3004 Bedienungsanleitung

14 August 2024

Mtx Audio RT604 Bedienungsanleitung

13 August 2024

Bedienungsanleitung Empfänger

Neueste Bedienungsanleitung für -Kategorien-

Rotel RA‑1592MKII Bedienungsanleitung

16 Oktober 2024

Denon AVR-S900W Bedienungsanleitung

16 Oktober 2024

Pro-Ject Amp Box DS2 Bedienungsanleitung

15 Oktober 2024

AKG HP12U Bedienungsanleitung

15 Oktober 2024

Sennheiser EM 9046 SU Bedienungsanleitung

14 Oktober 2024

Yamaha MusicCast RX-V481 Bedienungsanleitung

14 Oktober 2024

JL Audio VX600/6i Bedienungsanleitung

12 Oktober 2024

Pioneer SX-303RDS Bedienungsanleitung

10 Oktober 2024

Technics SA-160L Bedienungsanleitung

8 Oktober 2024

Avantree Audiplex Bedienungsanleitung

7 Oktober 2024