Mtx Audio RFL4120 Bedienungsanleitung


Lesen Sie kostenlos die šŸ“– deutsche Bedienungsanleitung fĆ¼r Mtx Audio RFL4120 (40 Seiten) in der Kategorie Autoradio. Dieser Bedienungsanleitung war fĆ¼r 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/40
mtxaudio.eu
mtxaudio.fr
mtxaudio.de
facebook.com/MTXEurope
facebook.com/MTXFrance
twitter.com/MTXEurope
twitter.com/MTXFrance
instagram.com/mtxaudio.eu/
instagram.com/mtxaudio.fr/
RFL4120
High-End 4-Channel Class-AB Ampliļ¬er - 800W RMS - 3200W Peak
Designed by MTX in Phoenix, AZ - USA
Ampliļ¬cateur 4 canaux Classe-AB haut de gamme - 800W RMS - 3200W Peak
ConƧu par MTX Ơ Phoenix, AZ - USA
High-End 4-Kanal Class-AB VerstƤrker - 800W RMS - 3200W Peak
Entwickelt von MTX in Phoenix, AZ - USA
Ownerā€™s Manual - MTX RFL4120
Thank You !
Thank you for purchasing an MTX Audio High-End ampliļ¬er. Proper installation matched with MTX speakers and subwoofers provide
superior sound and performance for endless hours of waking the neighbors, slamminā€™ your friends or ļ¬‚at out stomping wanna-be
players. Congrats and enjoy the ultimate audio experience with MTX !
Speciļ¬cations :
ā€¢ 4-Channel Class-AB ampliļ¬er
ā€¢ CEA2006 certiļ¬ed Power Output :
- 200 Watts RMS x 4-channels at 2 ohm and THD+N ā‰¤1%
- 120 Watts RMS x 4-channels at 4 ohm and THD+N ā‰¤1%
- 400 Watts RMS bridged x 2 at 4 ohm and THD+N ā‰¤1%
ā€¢ Crossover :
- High pass 12dB/oct variable from 40Hz to 5000Hz
- Low pass 24dB/oct variable from 40Hz to 5000Hz
- Band pass 12dB-24dB/oct variable from 40Hz to 5000Hz
ā€¢ Signal-to-Noise Ratio (1 Watt) : > 98dB
ā€¢ THD+Noise (Distortion) (1 Watt) : ā‰¤ 0,05%
ā€¢ Frequency Response (Ā±1dB) : 10Hz-90000Hz
ā€¢ Maximum Input Signal : 6V
ā€¢ Maximum Sensitivity : 200mV
ā€¢ EBC remote control
ā€¢ Dimensions : 525mm x 204mm x 59mm
25A 25A 25A 25A
+1 2VGND
Powe r Fuse s
REM
Input
Ch.1 Ch.2
Gain
6V - 0,2V
Ch.1 Ch.2
Speakers
Bridge
(+)
(+)
(-) (+) ( -)
(-)
Ch.3 Ch.4
Ch.1 Ch .2 Ch.3 Ch.4
Input
EBC
Remo teGain
6V - 0,2V
High Pass
Low Pas s
40Hz - 5000Hz
40Hz - 5000Hz
On
Off
On
Off
High Pass
Low Pas s
40Hz - 5000Hz
40Hz - 5000Hz
On
Off
On
Off
Ch.3 Ch.4
Speakers
Bridge
(+)
(+)
(-) (+) ( -)
(-)
Input
Ch.1 Ch.2
Gain
6V - 0,2V
High Pass
Low Pass
40Hz - 5000H z
40Hz - 5000H z
On
Off
On
Off
Ch.3 Ch.4
Ch.1 Ch.2 Ch 4
Input
EBC
Remote
Gain
6V - 0,2V
High Pass
Low Pass
40Hz - 5000H z
40Hz - 5000H z
On
Off
On
Off
RCA Inputs - These RCA inputs are used with head units that have RCA or Line level outputs (head units need a minimum level of
200mV output for proper operation of the ampliļ¬er).
MTX recommends only high quality RCA cables to decrease the possibility of radiated noise entering the system.
Gain Control - The gain control matches the input sensitivity of the ampliļ¬er to the head unit being used. The operating range varies
from 200mv to 6V.
Adjusting the gain
1. Turn the gain control on the ampliļ¬er all the way down (counter clockwise).
2. Turn up the volume control on the head unit to approximately 3ā„4 of maximum.
3. Adjust the gain control on the ampliļ¬er until audible distortion occurs.
4. Adjust the gain control down until audible distortion disappears.
5. The ampliļ¬er is now calibrated to the output of the head unit.
Low Pass X-Over Switch - Turns the active low pass (LP) x-over on and oļ¬€. When engaged (On) the x-over is ā€œONā€, when disengaged
(Oļ¬€) the x-over is ā€œOFFā€
Low Pass X-Over Frequency Control - Used to select the desired low-pass (LP) x-over frequency. The frequency is adjustable from 40Hz
to 5000Hz.
High Pass X-Over Switch - Used to turn on the active high-pass (HP) x-over on and oļ¬€. When engaged (On) the x-over is ā€œONā€, when
disengaged (Oļ¬€) the x-over is ā€œOFFā€.
High Pass X-Over Frequency Control - Used to select the desired high-pass (HP) x-over frequency. The frequency is adjustable from
40Hz to 5000Hz.
Band Pass X-Over : To use, turn ā€œONā€ the LP (3) and HP (5) x-overs at the same time, creating a band-pass x-over for kick woofers or
midranges. You can tune the ļ¬lter with frequency controls (4) and (6).
Input Switch : If the head unit is equipped with 4 RCA outputs (2 front and 2 rear), use the ch-3 ch-4 mode and connect the 4 RCA
outputs to the ch-1 ch-2 ch-3 ch-4 RCA inputs on the amp. If only 2 RCA outputs are available from the head unit, use the ch-1 ch-2
mode and connect the RCA outputs to the ch-1 and ch-2 inputs of the amp.
EBC Port (External Bass Control) - The Remote Subwoofer Level Control (EBC) plugs directly into this port, while the EBC itself can be
placed anywhere in the vehicle for on demand bass adjustments. EBC is included.
Controls and Inputs :


Produktspezifikationen

Marke: Mtx Audio
Kategorie: Autoradio
Modell: RFL4120

Brauchst du Hilfe?

Wenn Sie Hilfe mit Mtx Audio RFL4120 benƶtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Autoradio Mtx Audio

Bedienungsanleitung Autoradio

Neueste Bedienungsanleitung fĆ¼r -Kategorien-