Moxa SPL-24-T Bedienungsanleitung

Moxa Netzwerkkarte / Adapter SPL-24-T

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Moxa SPL-24-T (7 Seiten) in der Kategorie Netzwerkkarte / Adapter. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/7

P/N: 1802000240111

*1802000240111*

SPL 24 Series -

Quick Installation Guide

PoE Splitter

Vers 20ion 6.2 , May 21

Technical Support Contact Information

www.moxa.com/support



2 . A 20 1 Moxa Inc ll rights reserved.

- - 2

Overview

The SPL-24 plays the role of PD, and splits the data signal and power

signal that are transmitted from the PSE. The SPL-24 plays a dual role of

providing power to industrial devices, and enabling Ethernet connections.

The SPL- -24 have a wide operating temperature range of 40 to 75°C, and

are designed to withstand a high degree of vibration and shock. The

rugged hardware design makes the SPL-24 perfect for ensuring that your

Ethernet equipment can operate in critical industrial environments, such

as in hazardous locations, and complies with FCC and CE standards.

NOTE

Throughout this Hardware Installation Guide, we use EDS as an

abbreviation for Moxa EtherDevice Switch, and we use SPL as an

abbr

eviation for Moxa PoE Splitter:

SPL = Moxa PoE Splitter

Wiring Requirements

WARNING

Do not disconnect modules or wires unless the power supply has

been switched off or the area is known to be non

hazardous. The

devices may only be connected to the

supply voltage shown on

the type plate. The devices are designed for operation with a

Safety Extra

Low Voltage. Thus, they may only be connected to

the supply voltage connections and to the signal contact with the

Safety Extra

- Low Voltages (SELV) in compliance with IEC

60950-1/EN 60950-1.

WARNING

The power for this product is intended to be supplied by a Listed

Power Unit, with output marked LPS, and rated to deliver 48 VDC

at a maximum of 300 mA.

WARNING

This unit is a built

-in type. When the unit is installed in another

piece of equipment, the equipment enclosing the unit must

comply with fire enclosure regulation IEC 60950

-1 -1 /EN60950

(or similar regulation).

- - 3

WARNING

Safety First!

Be sure to disconnect the power cord before installing and/or

wiring your

Moxa EtherDevice Switch. Calculate the maximum

possible current in each power wire and common wire.

Observe

all electrical codes dictating the maximum current allowable for

each wire size. If the current goes above the maximum ratings,

the wiring could overheat, causing serious damage to your

equipment.

You should also pay attention to the following items:

• Use separate paths to route wiring for power and devices. If power

wiring and device wiring paths must cross, make sure the wires are

perpendicular at the intersection point.

NOTE: Do not run signal or communications wiring and power wiring

in the same wire conduit. To avoid interference, wires with different

signal characteristics should be routed separately.

• You can use the type of signal transmitted through a wire to

determine which wires should be kept separate. The rule of thumb is

that wiring that shares similar electrical characteristics can be

bundled together.

• Keep the input wiring and the output wiring separated.

• It is strongly advised that you label the wiring to all devices in the

system when necessary.

Package Checklist for SPL-24

The Moxa SPL-24 is shipped with the following items. If any of these items

is missing or damaged, please contact your customer service

representative for assistance.

• - Moxa PoE Splitter, SPL 24

• i g Quick nstallation uide (printed)

• Warranty card

Features of SPL 24-

High Performance Network Switching Technology

• IEEE802.3af compliance

• - Power/data split from PoE lines using either spare pairs or data pairs

• Support for up to 12.95 W at 24 VDC

• Support for up to 15.4 watts per PoE port

• Short circuit protection

• Auto disconnection for over voltage or under voltage

• Power consumption detection and classification

Rugged Design

• Operating temperature range from 0 to 60°C, or extended operating

temperature from - - 40 to 75°C for “ T” models

• IP30, plastic case

• D - IN Rail or panel mounting ability

Produktspezifikationen

Marke:	Moxa
Kategorie:	Netzwerkkarte / Adapter
Modell:	SPL-24-T
Gewicht:	95 g
Zertifizierung:	FCC, EN 55022, UL 69050-1, IEC 60068-2-27, IEC 60068-2-32, IEC 60068-2-6
Power over Ethernet (PoE):	Ja
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	2
LED-Anzeigen:	Ja
Abmessungen (BxTxH):	24.9 x 100 x 86.2 mm
Eingangsspannung:	44 - 75 V
Konformität mit Industriestandards:	802.3af, 802.3, 802.3u
Power over Ethernet (PoE) Spannung:	24 V