Minute Man SSL-SMOKE Bedienungsanleitung

Minute Man Rauchmelder SSL-SMOKE

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Minute Man SSL-SMOKE (3 Seiten) in der Kategorie Rauchmelder. Dieser Bedienungsanleitung war für 31 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/3

SSL-SMOKE User’s Manual

IMPORTANT: Read all of the instructions before

attempting to install the SSL-SMOKE detector.

DESCRIPTIONS

The SSL-SMOKE detector is a device, which connects with

SSL-EMD. When smoke is detected an alarm will sound

alerting the users. Through the SNMP-SSL card, the user can

monitor it and receive notifications of the alarms.

This type o

C/DC smoke detector can be powered by 120VAC utility

power or a 9-volt battery. AC/DC smoke detectors offer added

protection in the event of a power failure or a dead battery.

INSTALLATION

1. Detach the cover by twisting it until it unlatches from the

smoke detector base.

2. Using the smoke detector base as pattern, trace outlines o

the two keyhole slots onto the mounting surface.

3. Drill a pilot hole in the center of the small end of each of the

keyhole slots in the mounting surface.

4. Insert and tighten the mounting screws in the pilot holes

leaving approximately 1/8” of the screws sticking out.

5. Mount the smoke detector base making sure that screws

are positioned in the small ends of the keyholes and tighten

the screws.

6. Snap on the battery wire clip and insert the battery into

battery holder.

7. Replace the cover by twisting it until it latches. The smoke

detector is now operating.

8. Test the smoke detector by pushing test button on cove

and holding the button down for about 2-seconds.

Use the following steps to set-up and connect the

SSL-SMOKE detector to the SSL-EMD:

1. Loosen the screws on SSL-EMD.

2. Connect the wires from the SSL-SMOKE detector to the

SSL-EMD Alarm-1 and/or Alarm-2, and then tighten the screws.

3. Connect the straight-through CAT5 network cable from the

SNMP-SSL card’s RJ45 connector labeled “COM” to the

connector labeled “010101” on the SSL-EMD.

4. Verify that the SNMP-SSL card has a network connection and

is powered on.

5. Check the LED (Power/Status) of SSL-EMD, it will flash ever

5-seconds.

6. Open a Web browser and connect to the SNMP-SSL card.

7. Change the setting of “SSL-EMD Status” from “Disable” to

“Auto” on the EMD Configuration page.

8. Set the status of Alarm-1 and/or Alarm-2 to “Normal Open”.

9. The installation of the SSL-SMOKE detector is complete. See

the SNMP-SSL User’s Manual.

Note: The SSL-SMOKE detector operates with 120VAC or a

9-volt battery. Connecting to the 120VAC utility power is not

required to operate the detector. However, operating with both

the utility power and the battery offers added protection in the

event of a power failure or a dead battery.

LIMITED PRODUCT WARRANTY

Para Systems Inc. (Para Systems) warrants this equipment, when

properly applied and operated within specified conditions, against

faulty materials or workmanship for a period of three years from the

date of original purchase by the end user. For equipment sites within

the United States and Canada, this warranty covers repair o

replacement of defective equipment at the discretion of Para Systems.

Repair will be from the nearest authorized service center.

Replacement parts and warranty labor will be borne by Para Systems.

For equipment located outside of the United States and Canada, Para

Systems only covers faulty parts. Para Systems products repaired o

replaced pursuant to this warranty shall be warranted for the remaining

portion of the warranty that applies to the original product. This

warranty applies only to the original purchaser who must have properl

registered the product within 10 days of purchase.

The warranty shall be void if (a) the equipment is damaged by the

customer, is improperly used, is subjected to an adverse operating

environment, or is operated outside the limits of its electrical

specifications; (b) the equipment is repaired or modified by anyone

other than Para Systems or Para Systems-approved personnel; or (c)

has been used in a manner contrary to the product's operating manual

or other written instructions.

ny technical advice furnished before or after delivery in regard to use

or application of Para Systems’s equipment is furnished without charge

and on the basis that it represents Para Systems’s best judgment

under the circumstances, but it is used at the recipient's sole risk.

EXCEPT AS PROVIDED HEREIN, PARA SYSTEMS MAKES NO

WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR

PARTICULAR PURPOSE. Some states do not permit limitation o

implied warranties; therefore, the aforesaid limitation(s) may not apply

to the purchaser.

EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL PAR

SYSTEMS BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF

THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGE. Specifically, Para Systems is not

liable for any costs, such as lost profits or revenue, loss of equipment,

loss of use of equipment, loss of software, loss of data, cost o

substitutes, claims by third parties, or otherwise. The sole and

exclusive remedy for breach of any warranty, expressed or implied,

concerning Para Systems’s products and the only obligation of Para

Systems hereunder, shall be the repair or replacement of defective

equipment, components, or parts; or, at Para Systems’s option, refund

of the purchase price or substitution with an equivalent replacement

product. This warranty gives you specific legal rights and you may

also have other rights, which vary from state to state.

OBTAINING TECHNICAL ASSISTANCE

Para Systems (Minuteman UPS) Technical Support:

Phone: 1-972-446-7363

Fax: 1-972-446-9011

Web: www.minutemanups.com/support/con_tech2.php

SSL-SMOKE User’s Manual

IMPORTANT: Read all of the instructions before

attempting to install the SSL-SMOKE detector.

OPERATION, TESTING AND MAINTENANCE

Operation: The smoke detector is operating once the

battery is connected. When products of combustion are

sensed, the unit sounds a loud pulsating alarm until you

push the reset button once. Note: When the battery is

replaced or tested or the alarm is reset the smoke detecto

will operate normally after two minutes.

Testing: Test by pushing test button on cover and holding

the button down for about 2-seconds. This will sound an

alarm if all electronic circuitry is working properly. If no

alarm sounds, the unit has a defective battery or othe

failure. You can also test the smoke detector by blowing

smoke into it. Test the smoke detector monthly to assure

proper operation. Erratic noise or low sound from the

smoke detector may indicate a defective smoke detector.

Return it for service.

Warning: Test the smoke detector operation if an RV or a

mobile home vehicle has been in storage, and before each

trip, and at least once per week during use.

Maintenance: The smoke detector is virtually

maintenance free. However, under dusty conditions, a

vacuum may be used to clear the sensing chamber o

dust. Do not remove smoke detector cover when

vacuuming. These smoke detectors use a high technolog

electronic chamber. Do not try to repair the smoke detector.

BATTERY REPLACEMENT

The smoke alarm is powered by one 9V carbon-zinc

battery (alkaline batteries may also be used). The battery

should provide operation for at least one year unde

normal operating conditions. The smoke alarm has a low

battery indicator, which will “chirp” at approximately

20-second intervals for a minimum of 7-days. Replace the

battery when chirping occurs. Use only 9-volt batteries.

THE LIMITATIONS OF SMOKE DETECTORS

Smoke detectors are devices that can provide early warnings

of possible developing fires at a reasonable cost. However,

smoke detectors have certain limitations. For battery

powered smoke detectors, the battery must be in good

condition and installed properly.

Smoke detectors cannot sound an alarm if smoke does not

reach the detector. Therefore smoke detector may not sense

fires starting in chimneys, walls, on roofs, on the other side o

a closed door, or on a different floor. For maximum

protection, a smoke detector should be installed in each

separate sleeping area and on every level of a home.

lthough smoke detector can help save lives by providing

early warnings of a fire, they are not a substitute for an

insurance policy. Homeowners and renters should have

adequate insurance to protect their lives and property.

WHAT TO DO WHEN THE ALARM SOUNDS

• Leave immediately. Every second counts, so don’t waste

time getting dressed or picking up valuables.

• In leaving, do not open any inside door without first

feeling its surface. If hot, or if you see smoke seeping

through the cracks, do not open that door! Instead, use

your alternate exit. If the inside door is cool, place you

shoulder against it and open it slightly, but be ready to

slam it shut if fire and/or smoke come in.

• Stay close to the floor if air is smoky. Breathe shallowly

through a cloth if possible wet it.

• Once outside, go to your selected meeting place and

make sure everyone is there.

• Call the fire department from your neighbor’s home - not

from yours!

• Do not return to your home until fire officials say that it’s

all right to do so.

Further information on fire safety can be obtained in a

pamphlet titled “In A Fire Seconds Count” published by the

NFPA, Batterymarch Park, Quincy, Mass 02269.

FALSE ALARMS

The smoke alarm is designed to minimize false alarms.

Smoking will not normally set off the alarm unless smoke is

blown directly into the detector. Combustion particles from

cooking may set off the alarm if the detector is located close

to the kitchen. Large quantities of combustion particles are

generated from spills or broiling.

If the detector does alarm, check for fires first. If a fire is

discovered, get out and call the fire department. If no fire is

present, check to see if one of the reasons listed above

may have caused the alarm.

NATIONAL FIRE PROTECTION ASSOCIATION

REQUIRED PROTECTION

For your information, the National Fire Protection

ssociation’s Standard 74, Section 2-1 provides information

regarding the smoke detection equipment required within

the family living unit. Section 2-1, 1.1 reads as follows:

“Smoke detectors shall be installed outside of each

separate sleeping area in the immediate vicinity of the

bedrooms and on each additional story of the family living

unit including basements and excluding crawl spaces and

unfinished attics.

The provisions of 2-1, 1.1 represent the minimum numbe

of detectors required by this standard. It is recommended

that the householder consider the use of additional smoke

or heat detectors for increased protection for those areas

separated by a door from the areas protected by the

required smoke detectors under 2-1, 1.1 above. The

recommended additional areas are living room, dining

room, bedroom(s), kitchen, attic (finished or unfinished),

furnace room, utility room, basement, integral or attached

garage, and hallways not included in 2-1, 1.1 above.

However, the use of additional detectors remains the opting

of the householder.”

The equipment should be installed in accordance with the

National Fire Protection Association’s Standard 74 (NFPA,

Batterymarch Park, Quincy, Mass 02269)

NOTIFY YOUR LOCAL FIRE DEPARTMENT AND

INSURANCE COMPANY THAT A SMOKE DETECTO

HAS BEEN INSTALLED

34000363 R1

SSL-SMOKE User’s Manual

IMPORTANT: Read all of the instructions before

attempting to install the SSL-SMOKE detector.

RECOMMENDED LOCATIONS OF SMOKE DETECTORS

IN A HOUSE

• Place the first smoke detector in the immediate area o

the bedrooms. Try to protect the exit path as the

bedrooms are usually farthest from an exit. If more

than one sleeping area exists, locate additional smoke

detectors in each sleeping area.

• Position smoke detectors to protect any stairway as

stairways act like chimneys for smoke and heat.

• Mount at least one smoke detector on every floor.

• Place a smoke detector in every bedroom where a

smoker sleeps.

• Place a smoke detector in every room where electrical

appliances are operated (i.e. portable heaters o

humidifiers).

• Place a smoke detector in every room where someone

sleeps with the door closed. The closed door may

prevent the alarm from waking the sleeper.

• Smoke, heat and other combustion products rise to

the ceiling and spread horizontally. Mounting the

smoke detector on the ceiling in the center of the room

places it closest to all points in the room. Ceiling

mounting is preferred in ordinary residential

construction.

• For mobile home installation, select location carefully

to avoid the thermal barrier that may form at the

ceiling. For more detail, see Mobile Home Installation.

• When mounting the smoke detector on the ceiling

mount it at a minimum of 4” (10 cm) from the sidewall

and 2 feet (60.96cm) from any corner (See Diagram).

• If ceiling mounting is not possible and wall mounting is

permitted by your local and state codes, put the smoke

detectors between 4 and 6 inches (10 and 15 cm) from

the ceiling (See Diagram).

• Put a smoke detector at both ends of a bedroom

hallway if the hallway is more than 30 feet long.

MOBILE HOME INSTALLATION

Mobile homes built in the past five to seven years have been

designed and insulated to be energy efficient. Install smoke

detectors as recommended (refer to RECOMMEND

LOCATIONS OF DETECTORS IN A HOUSE and Diagram).

In mobile homes that are not well insulated compared to

present standards, extreme heat or cold can be transferred

from outside through poorly insulated walls and roof. This

may create a thermal barrier, which can prevent smoke from

reaching a smoke detector mounted on the ceiling. In such

units, install smoke detector on inside partition between 4

and 6 inches (10 and 15 cm) from the ceiling (See Diagram).

AVOID THESE LOCATIONS

• The kitchen-smoke from cooking might cause an

unwanted alarm.

• The garage, products of combustion are present when

you start your automobile.

• In front of forced air ducts used for heating and ai

conditioning and other high air flow areas.

• In the peak of an “A” frame type ceiling.

• In areas where temperatures may fall below 40º or rise

above 100º.

• In dusty areas, dust particles may cause smoke

detectors to false alarm or fail to alarm.

• In very humid areas or near a bathroom, moisture can

cause false alarm.

• NEAR ELECTRICAL LIGHTS – Electrical “Noise” from

electrical lights may cause nuisance alarm. Put smoke

detectors at least 5 feet (1.5 meters) from such lights.

GOOD SAFETY HABITS

There are situations where a smoke detector may not be

effective to protect against fire as stated in the NFP

standard 74. For instance:

• Smoking in bed

• Leaving children home alone

• Cleaning with flammable liquids, such as gasoline

DEVELOP AND PRACTICE A PLAN OF ESCAPE

• Make a floor plan indicating all doors and windows and

at least two escape routes from each room. Second

story windows may need a rope or chain ladder.

• Have a family meeting and discuss your escape plan,

showing everyone what to do in case of fire.

• Determine a place outside your home where all of you

can meet, if a fire occurs.

• Familiarize everyone with the sound of the Smoke

Alarm and train them to leave your home when they

hear it.

• Identify children’s bedrooms with red stickers placed in

the upper left corner of the windows.

• Practice a fire drill at least every six months. Practice

allows you to test your plan before emergency. You

may not be able to reach your children. It is important

that they know what to do!

34000363 R1

Produktspezifikationen

Marke:	Minute Man
Kategorie:	Rauchmelder
Modell:	SSL-SMOKE
Produktfarbe:	Black, Grey
Übertragungstechnik:	Kabelgebunden
Energiequelle:	AC/DC
Akku-/Batteriespannung:	9 V