Milwaukee M28 0726-22 Bedienungsanleitung

Milwaukee bohren M28 0726-22

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Milwaukee M28 0726-22 (13 Seiten) in der Kategorie bohren. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/13

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S

MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN

COMPRENDRE LE MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL

MANUAL DEL OPERADOR.

28 V 1/2" HAMMER-DRILL

PERCEUSE À PERCUSSION DE 13 mm (1/2") 28 V

TALADRO DE PERCUSIÓN DE 13 mm (1/2") DE 28 V

Cat. No.

No de cat.

0726-20

2 3

FUNCTIONAL DESCRIPTION

SPECIFICATIONS

Cat. No.

Volts

No Load

RPM

No Load

Blows per

Minute

Capacities

Steel

Wood

MasonryFlat Bit Auger Bit Hole Saw Screws (dia.)

0726-20 28 Low 0-450

High 0-1800

Low 0-7200

High 0-28,800 1/2" 1-1/2" 1-1/2" 2-9/16" 1/4" 5/8"

1. Trigger

2. Control switch

3. LED

4. Keyless chuck

5. Torque selector collar

6. Application selector collar

7. Speed selector

8. Side handle

SYMBOLOGY

Use only MILWAUKEE M28™ or V28® battery packs.

Volts

Direct Current

No Load Revolutions per

Minute (RPM)

C US Underwriters Laboratories, Inc.

United States and Canada

PERSONAL SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WORK AREA SAFETY

ELECTRICAL SAFETY

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power tools in explosive atmos-

pheres, such as in the presence of ﬂ ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁ ed plugs and matching outlets will

reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase

the risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use

of a cord suitable for outdoor use reduces the risk

of electric shock.

• If operating a power tool in a damp location is

unavoidable, use a ground fault circuit inter-

rupter (GFCI) protected supply. Use of an GFCI

reduces the risk of electric shock.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

• Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

• If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS. Failure

to follow the warnings and instructions may result in electric shock, ﬁ re and/or serious

injury. Save all warnings and instructions for future reference. The term "power

tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

• Do not use the power tool if the switch does not

turn it on and o. Any power tool that cannot be

controlled with the switch is dangerous and must

be repaired.

• Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such pre-

ventive safety measures reduce the risk of starting

the power tool accidentally.

• Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

• Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power tool

for operations dierent from those intended could

result in a hazardous situation.

• Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inﬂ uence of drugs, alcohol or medi-

cation. A moment of inattention while operating

power tools may result in serious personal injury.

• Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

• Prevent unintentional starting. Ensure the

switch is in the o-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your ﬁ nger on the switch or energising power tools

that have the switch on invites accidents.

SERVICE

• Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

SPECIFIC SAFETY RULES

BATTERY TOOL USE AND CARE

• Recharge only with the charger speciﬁ ed by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of ﬁ re

when used with another battery pack.

• Use power tools only with speciﬁ cally desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and ﬁ re.

• When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery terminals

together may cause burns or a ﬁ re.

• Under abusive conditions, liquid may be eject-

ed from the battery; avoid contact. If contact

accidentally occurs, ﬂ ush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation

or burns.

• Wear ear protectors when impact drilling.

Exposure to noise can cause hearing loss.

•

Use auxiliary handle(s), if supplied with the

tool. Loss of control can cause personal injury.

• Hold power tool by insulated gripping

surfaces, when performing an operation

where the cutting accessory may contact

hidden wiring or its own cord. Cutting

accessory contacting a “live” wire may make

exposed metal parts of the power tool “live” and

could give the operator an electric shock.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

• WARNING Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to cause

cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and

other masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are spe-

cially designed to ﬁ lter out microscopic particles.

4 5

OPERATION

WARNING To reduce the risk of injury,

wear safety goggles or glasses with side

shields.

ASSEMBLY

Inserting/Removing Battery Pack

Insert the battery pack from the front by sliding

battery pack into the body of the tool. Insert the

battery pack until the battery latches lock.

To remove the battery pack, press in both battery

latches and slide the battery pack o of the tool.

WARNING Recharge only with the

charger speciﬁ ed for the battery. For speciﬁ c

charging instructions, read the operator’s

manual supplied with your charger and

battery.

WARNING Always remove battery

pack before changing or removing acces-

sories. Only use accessories specifically

recommended for this tool. Others may be

hazardous. The torque speciﬁ cations shown here are ap-

proximate values.

Torque selector

collar setting

Torque

1 - 5 0 - 16 in. lbs.

6 - 10 17 - 27 in. lbs.

11 - 15 28-37 in. lbs.

16 - 20 38-46 in. lbs.

21-24 47-60 in. lbs.

Drill 1 Low

2 High

800 in. lbs.

370 in. lbs.

NOTE: The number selected on the torque collar

has no eect on operation of the drill in hammer

mode.

NOTE: When using carbide bits, do not use wa-

ter to settle dust. Do not attempt to drill through

steel reinforcing rods. This will damage the

carbide bits.

2. To use the drilling only mode, rotate the ap-

plication selector collar until the drill symbol

appears in line with the arrow.

NOTE: The number selected on the torque collar

has no eect on operation of the drill in drilling

mode.

3. To use the driving screws mode rotate the

application selector collar until the drive symbol

appears in line with the arrow. Then rotate

the torque selector collar until the desired clutch

setting appears in line with the arrow.

The adjustable clutch, when properly adjusted,

will slip at a preset torque to prevent driving the

screw too deep into dierent materials and to

prevent damage to the screw or tool.

Installing the Side Handle

1. To install the side handle,

loosen the side handle

grip until the hooks are

far enough apart to ﬁ t into

the slots on the gear case

ring. Position the side

handle on the top, left,

or right side of the tool.

Tighten the side handle grip until it is secure.

2. To remove the side handle, loosen the side

handle grip until the side handle can be removed.

Reposition and tighten securely.

WARNING To reduce the risk of injury,

always use a side handle when using this tool.

Always brace or hold securely. Ensure side

handle is tightened securely before each use.

Using Keyless Chucks

This tool is equipped with a spindle lock. The chuck

can be tightened with one hand, creating higher grip

strengths on the bit.

Always remove the battery pack before inserting

or removing bits.

1. To open the chuck jaws, turn the sleeve in the

counterclockwise direction.

When using drill bits, allow the bit to strike the

bottom of the chuck. Center the bit in the chuck

jaws and lift it about 1/16" o of the bottom.

When using screwdriver bits, insert the bit far

enough for the jaws to grip the hex of the bit.

2. To close the chuck jaws, turn the sleeve in the

clockwise direction. The bit is secure when the

chuck makes a ratcheting sound and the sleeve

can not be rotated any further.

3. To remove the bit, turn the sleeve in the coun-

terclockwise direction.

NOTE: A ratcheting sound may be heard when the

chuck is opened or closed. This noise is part of the

locking feature, and does not indicate a problem

with the chuck’s operation.

Selecting Speed

The speed selector is on top of the motor housing.

Allow the tool to come to a complete stop before

changing speeds. See “Applications” for recom-

mended speeds under various conditions.

1. For Low speed (up to 450 RPM), push the speed

selector to display “1”.

2. For High speed (up to 1800 RPM), push the

speed selector to display “2”.

Selecting Hammer, Drill or Drive Action

MILWAUKEE Hammer-Drills have three operating

modes: drilling with hammering action, drilling only,

and driving screws. To set the operating mode,

rotate the application selector collar and torque

selector collar to the desired symbols.

1. To use the hammer-drilling mode, rotate the

application selector collar until the hammer

symbol appears in line with the arrow. Ap-

ply pressure to the bit to engage the hammering

mechanism.

NOTE: Because the above settings are only a

guide, use a piece of scrap material to test the dif-

ferent clutch positions before driving screws into

the workpiece.

Using Control Switch

The control switch may be set to three positions:

forward, reverse and lock. Due to a lockout mecha-

nism, the control switch can only be adjusted when

the ON/OFF switch is not pressed. Always allow

the motor to come to a complete stop before using

the control switch.

For forward (clockwise) rotation, push in the control

switch from the right side of the tool. Check the

direction of rotation before use.

For reverse (counterclockwise) rotation, push in the

control switch from the left side of the tool. Check

direction of rotation before use.

Fig. 5

Push for

Forward

Push for

Reverse

PUSH TO CENTER TO LOCK

To lock the trigger, push the control switch to the

center position. The trigger will not work while

the control switch is in the center locked position.

Always lock the trigger before storing the tool and

any time the tool is not in use.

Fig. 4

To Drive Screws

Fig. 2

To Hammer

Fig. 3

To Drill

Starting, Stopping and Controlling Speed

1. To start the tool, grasp the handle ﬁ rmly and pull

the trigger.

NOTE: An LED is turned on when the trigger is

pulled.

2. To vary the speed, increase or decrease the

pressure on the trigger. The further the trigger

is pulled, the greater the speed.

3. To stop the tool, release the trigger. Make sure

the bit comes to a complete stop before laying

the tool down.

Drilling

Place the bit on the work surface and apply ﬁ rm

pressure before starting. Too much pressure will

slow the bit and reduce drilling efﬁ ciency. Too little

pressure will cause the bit to slide over the work

area and dull the point of the bit.

If the tool begins to stall, reduce pressure slightly

to allow the bit to regain speed. If the bit binds,

reverse the motor to free the bit from the workpiece.

WARNING To reduce the risk of injury,

always use a side handle when using this tool.

Always brace or hold securely. Ensure side

handle is tightened securely before each use.

WARNING Always remove battery

pack before changing or removing acces-

sories. Only use accessories specifically

recommended for this tool. Others may be

hazardous.

Fig. 1

Hooks

Slots

Produktspezifikationen

Marke:	Milwaukee
Kategorie:	bohren
Modell:	M28 0726-22

Brauchst du Hilfe?

Wenn Sie Hilfe mit Milwaukee M28 0726-22 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung bohren Milwaukee

Milwaukee M18 Fuel Super Hawg 2709-22 Bedienungsanleitung

8 Oktober 2024

Milwaukee 5376-20 Bedienungsanleitung

1 Oktober 2024

Milwaukee M18 Bedienungsanleitung

13 September 2024

Milwaukee PH 30 Power X Bedienungsanleitung

13 September 2024

Milwaukee 5426-21 Bedienungsanleitung

11 September 2024

Milwaukee M12 Fuel 3403-22 Bedienungsanleitung

10 September 2024

Milwaukee M18 Fuel 2788-22HD Bedienungsanleitung

8 September 2024

Milwaukee M18 FHACOD32 Bedienungsanleitung

3 September 2024

Milwaukee M18 ONEFHP Bedienungsanleitung

3 September 2024

Milwaukee M18 ONEFH Bedienungsanleitung

3 September 2024

Bedienungsanleitung bohren

Neueste Bedienungsanleitung für -Kategorien-

Ozito BDP-500 Bedienungsanleitung

16 Oktober 2024

MSW -DDM255 Bedienungsanleitung

16 Oktober 2024

MSW -DDM152 Bedienungsanleitung

16 Oktober 2024

MSW -DDM205 Bedienungsanleitung

16 Oktober 2024

MSW -DDM230 Bedienungsanleitung

16 Oktober 2024

Einhell BM-G1100 E Bedienungsanleitung

15 Oktober 2024

Sun Joe 24V-DDK-LTX-PNK Bedienungsanleitung

15 Oktober 2024

Makita DHR263ZJ Bedienungsanleitung

13 Oktober 2024

Rupes BH 252R Bedienungsanleitung

13 Oktober 2024

Black And Decker GC1800 Bedienungsanleitung

13 Oktober 2024