Milwaukee 9071-20 Bedienungsanleitung
Milwaukee
Schroefmachine
9071-20
Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Milwaukee 9071-20 (20 Seiten) in der Kategorie Schroefmachine. Dieser Bedienungsanleitung war fĂĽr 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/20
![](https://manualstech.ams3.cdn.digitaloceanspaces.com/html/nl/milwaukee/9071-20/html/bg1.png)
Cat. No. / No de cat.
9070-20, 9071-20, 9072-20, 9072-22, 9075-20, 9092-20, 9096-20
IMPACT WRENCH
CLÉ À PERCUSSION
LLAVE DE IMPACTO
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
![](https://manualstech.ams3.cdn.digitaloceanspaces.com/html/nl/milwaukee/9071-20/html/bg2.png)
2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings, instruc-
tions, illustrations and speciîšżca-
tions provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, îšżre and/or serious injury. Save all
warnings and instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodiîšżed plugs and matching outlets will
reduce risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of an GFCI reduces
the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your îšżnger on
the switch or energizing power tools that have the
switch on invites accidents.
• Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
• Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from
moving parts. Loose clothes, jewelry or long hair
can be caught in moving parts.
• If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power
tool for your application. The correct power tool
will do the job better and safer at the rate for which
it was designed.
•
Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
• Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many ac-
cidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
SERVICE
• Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
SPECIFIC SAFETY RULES FOR
IMPACT WRENCH
• Hold the power tool by insulated gripping sur-
faces, when performing an operation where the
fastener may contact hidden wiring or its own
cord. Fasteners contacting a “live” wire may make
exposed metal parts of the power tool “live” and could
give the operator an electric shock.
![](https://manualstech.ams3.cdn.digitaloceanspaces.com/html/nl/milwaukee/9071-20/html/bg3.png)
3
• Wear ear protectors when impact drilling. Expo-
sure to noise can cause hearing loss.
• Use only sockets and other accessories speci
-
cally designed for use on impact wrenches and
drivers. Other sockets and accessories might shatter
or break causing injury.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
•
WARNING
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
îšżlter out microscopic particles.
EXTENSION CORDS
Grounded tools require a three wire extension
cord. Double insulated tools can use either a two
or three wire extension cord. As the distance from
the supply outlet increases, you must use a heavier
gauge extension cord. Using extension cords with
inadequately sized wire causes a serious drop in
voltage, resulting in loss of power and possible tool
damage. Refer to the table shown to determine the
required minimum wire size.
The smaller the gauge number of the wire, the greater
the capacity of the cord. For example, a 14 gauge
cord can carry a higher current than a 16 gauge cord.
When using more than one extension cord to make
up the total length, be sure each cord contains at
least the minimum wire size required. If you are using
one extension cord for more than one tool, add the
nameplate amperes and use the sum to determine
the required minimum wire size.
Guidelines for Using Extension Cords
• If you are using an extension cord outdoors, be sure
it is marked with the sufx “W-A” (“W” in Canada)
to indicate that it is acceptable for outdoor use.
• Be sure your extension cord is properly wired
and in good electrical condition. Always replace a
damaged extension cord or have it repaired by a
qualiîšżed person before using it.
• Protect your extension cords from sharp objects,
excessive heat and damp or wet areas.
Recommended Minimum Wire Gauge
For Extension Cords*
Nameplate Amps
Extension Cord Length
25' 50' 75' 100' 150'
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 16.0
16.1 - 20.0
18
18
18
18
16
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
--
18
16
14
12
10
--
--
16
14
12
12
--
--
--
* Based on limiting the line voltage drop to îšżve volts at 150%
of the rated amperes.
GROUNDING
WARNING
Improperly connecting the ground-
ing wire can result in the risk of
electric shock. Check with a qualiîšżed electrician
if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug pro-
vided with the tool. Never remove the grounding
prong from the plug. Do not use the tool if the
cord or plug is damaged. If damaged, have it
repaired by a MILWAUKEE service facility before
use. If the plug will not îšżt the outlet, have a
proper outlet installed by a qualiîšżed electrician.
Grounded Tools (Three-Prong Plugs)
Tools marked “Grounding Required” have a three
wire cord and three prong grounding plug. The plug
must be connected to a properly grounded outlet
(See Figure A). If the tool should electrically mal-
function or break down, grounding provides a low
resistance path to carry electricity away from the
user, reducing the risk of electric shock.
The grounding prong in the plug is connected through
the green wire inside the cord to the grounding
system in the tool. The green wire in the cord must
be the only wire connected to the tool's grounding
system and must never be attached to an electrically
“live” terminal.
Your tool must be plugged into an appro-
Fig. A
priate outlet, properly installed and
grounded in accordance with all codes
and ordinances. The plug and outlet
should look like those in Figure A.
Double Insulated Tools (Two-Prong Plugs)
Tools marked “Double Insulated” do not require
grounding. They have a special double insulation
system which satisîšżes OSHA requirements and
complies with the applicable standards
Fig. B Fig. C
of Underwriters Laboratories, Inc., the
Canadian Standard Association and
the National Electrical Code. Double
Insulated tools may be used in either
of the 120 volt outlets shown in Figures
B and C.
SYMBOLOGY
Double Insulated
Amps
Volts
Alternating Current
Alternating Current/Direct Current
Impacts per Minute Under Load (IPM)
C US
UL Listing for Canada and U.S.
Approval Mark for Mexico
Produktspezifikationen
Marke: | Milwaukee |
Kategorie: | Schroefmachine |
Modell: | 9071-20 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Milwaukee 9071-20 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Schroefmachine Milwaukee
![Milwaukee](/images/pdf_free.png)
6 September 2024
![Milwaukee](/images/pdf_free.png)
4 September 2024
![Milwaukee](/images/pdf_free.png)
2 September 2024
![Milwaukee](/images/pdf_free.png)
11 August 2024
![Milwaukee](/images/pdf_free.png)
10 August 2024
![Milwaukee](/images/pdf_free.png)
8 August 2024
![Milwaukee](/images/pdf_free.png)
6 August 2024
![Milwaukee](/images/pdf_free.png)
6 August 2024
![Milwaukee](/images/pdf_free.png)
5 August 2024
![Milwaukee](/images/pdf_free.png)
5 August 2024
Bedienungsanleitung Schroefmachine
- Schroefmachine Panasonic
- Schroefmachine Cotech
- Schroefmachine Makita
- Schroefmachine Bosch
- Schroefmachine Laserliner
- Schroefmachine Parkside
- Schroefmachine Vonroc
- Schroefmachine AEG
- Schroefmachine Powerfix
- Schroefmachine Black And Decker
- Schroefmachine Cocraft
- Schroefmachine FERM
- Schroefmachine Ryobi
- Schroefmachine Senco
- Schroefmachine Skil
- Schroefmachine Hilti
- Schroefmachine DeWalt
- Schroefmachine Einhell
- Schroefmachine Elu
- Schroefmachine Festool
- Schroefmachine Mafell
- Schroefmachine Worx
- Schroefmachine Tacklife
- Schroefmachine Hikoki
- Schroefmachine Hitachi
- Schroefmachine Hazet
- Schroefmachine Metabo
- Schroefmachine Stanley
- Schroefmachine GĂĽde
- Schroefmachine Power Craft
- Schroefmachine Meec Tools
- Schroefmachine Dremel
- Schroefmachine Dedra
- Schroefmachine Silverline
- Schroefmachine Greenworks
- Schroefmachine Yato
- Schroefmachine Pansam
- Schroefmachine Toolland
- Schroefmachine Batavia
- Schroefmachine Matrix
- Schroefmachine Toolcraft
- Schroefmachine Fein
- Schroefmachine Ingersoll Rand
- Schroefmachine Craftsman
- Schroefmachine Powerplus
- Schroefmachine Alpha Tools
- Schroefmachine Ozito
- Schroefmachine Porter-Cable
- Schroefmachine Steren
- Schroefmachine Meister Craft
- Schroefmachine Einhell Bavaria
- Schroefmachine Wera
- Schroefmachine Rodcraft
- Schroefmachine Cleco
- Schroefmachine SW-Stahl
Neueste Bedienungsanleitung fĂĽr -Kategorien-
![Einhell](/images/pdf_free.png)
7 September 2024
![Einhell](/images/pdf_free.png)
7 September 2024
![Einhell](/images/pdf_free.png)
7 September 2024
![Vonroc](/images/pdf_free.png)
6 September 2024
![DeWalt](/images/logos/dewalt.png)
6 September 2024
![Stanley](/images/pdf_free.png)
6 September 2024
![Black And Decker](/images/pdf_free.png)
6 September 2024
![Ryobi](/images/logos/ryobi.png)
6 September 2024
![Ryobi](/images/logos/ryobi.png)
6 September 2024
![Ryobi](/images/logos/ryobi.png)
6 September 2024