Milwaukee 6142-31 Bedienungsanleitung

Milwaukee Sander 6142-31

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Milwaukee 6142-31 (28 Seiten) in der Kategorie Sander. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/28

Cat. No. / No de cat.

6141-30, 6141-31, 6142-30, 6142-31

4-1/2" GRINDERS

RECTIFIEUSES 115 mm (4-1/2")

ESMERILADORAS DE 115 mm (4-1/2")

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

WARNING To reduce the risk of injury, user must read and understand operator's manual.

AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien

comprendre le manuel.

ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.

GENERAL POWER TOOL

SAFETY WARNINGS

WARNING

Read all safety warnings, instruc-

tions, illustrations and specica-

tions provided with this power tool. Failure to

follow all instructions listed below may result in

electric shock, re and/or serious injury. Save all

warnings and instructions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-oper-

ated (cordless) power tool.

WORK ARE SAFETY

•

Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

• Do not operate power tools in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while operat-

ing a power tool. Distractions can cause you to lose

control.

ELECTRICAL SAFETY

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Un-

modied plugs and matching outlets will reduce risk

of electric shock.

• Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase the

risk of electric shock.

• Do not abuse the cord. Never use the cord for car-

rying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk

of electric shock.

• When operating a power tool outdoors, use an ex-

tension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

• If operating a power tool in a damp location is

unavoidable, use a ground fault circuit interrupter

(GFCI) protected supply. Use of an GFCI reduces

the risk of electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the inuence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personal injury.

• Use personal protective equipment. Always wear

eye protection. Protective equipment such as a dust

mask, non-skid safety shoes, hard hat or hearing

protection used for appropriate conditions will reduce

personal injuries.

• Prevent unintentional starting. Ensure the switch

is in the o󰀨-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your nger on the

switch or energizing power tools that have the switch

on invites accidents.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result

in personal injury.

• Do not overreach. Keep proper footing and bal-

ance at all times. This enables better control of the

power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewelry. Keep your hair and clothing away from

moving parts. Loose clothes, jewelry or long hair can

be caught in moving parts.

• If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust col-

lection can reduce dust-related hazards.

• Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles. A careless action

can cause severe injury within a fraction of a second.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it was

designed.

• Do not use the power tool if the switch does not turn

it on and o󰀨. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of

starting the power tool accidentally.

• Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrained users.

• Maintain power tools and accessories. Check for

misalignment or binding of moving parts, break-

age of parts and any other condition that may

a󰀨ect the power tool’s operation. If damaged,

have the power tool repaired before use. Many ac-

cidents are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly main-

tained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

• Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to

be performed. Use of the power tool for operations

di󰀨erent from those intended could result in a hazard-

ous situation.

• Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles

and grasping surfaces do not allow for safe handling

and control of the tool in unexpected situations.

SERVICE

• Have your power tool serviced by a qualied

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

SPECIFIC SAFETY RULES FOR

SANDER/GRINDER

Safety Warnings Common for Grinding, Sanding,

Wire Brushing or Abrasive Cutting-O󰀨 Operations:

• This power tool is intended to function as a

grinder, sander, wire brush or cut-o󰀨 tool. Read

all safety warnings, instructions, illustrations

and specications provided with this power tool.

Failure to follow all instructions listed below may result

in electric shock, re and/or serious injury.

• Operations such as polishing are not recom-

mended to be performed with this power tool.

Operations for which the power tool was not designed

may create a hazard and cause personal injury.

• Do not use accessories which are not specically

designed and recommended by the tool manufac-

turer. Just because the accessory can be attached to

your power tool, it does not assure safe operation.

• The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool. Accessories running faster than their rated

speed can break and y apart.

• The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories can

not be adequately guarded or controlled.

• Threaded mounting of accessories must match

the grinder spindle thread. For accessories

mounted by anges, the arbour hole of the ac-

cessory must fit the locating diameter of the

ange. Accessories that do not match the mounting

hardware of the power tool will run out of balance,

vibrate excessively and may cause loss of control.

• Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels

for chips and cracks, backing pad for cracks, tear

or excess wear, wire brush for loose or cracked

wires. If power tool or accessory is dropped, in-

spect for damage or install an undamaged acces-

sory. After inspecting and installing an accessory,

position yourself and bystanders away from the

plane of the rotating accessory and run the power

tool at maximum no-load speed for one minute.

Damaged accessories will normally break apart during

this test time.

• Wear personal protective equipment. Depending

on application, use face shield, safety goggles or

safety glasses. As appropriate, wear dust mask,

hearing protectors, gloves and workshop apron

capable of stopping small abrasive or workpiece

fragments. The eye protection must be capable of

stopping ying debris generated by various opera-

tions. The dust mask or respirator must be capable

of ltrating particles generated by your operation.

Prolonged exposure to high intensity noise may cause

hearing loss.

• Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of

workpiece or of a broken accessory may y away

and cause injury beyond immediate area of operation.

• Hold the power tool by insulated gripping surfaces

only, when performing an operation where the cut-

ting tool may contact hidden wiring. Contact with

a "live" wire may also make exposed metal parts of

the power tool "live" and could give the operator an

electric shock.

• Position the cord clear of the spinning accessory. If

you lose control, the cord may be cut or snagged and your

hand or arm may be pulled into the spinning accessory.

• Never lay the power tool down until the acces-

sory has come to a complete stop. The spinning

accessory may grab the surface and pull the power

tool out of your control.

•

Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could

snag your clothing, pulling the accessory into your body.

• Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing

and excessive accumulation of powdered metal may

cause electrical hazards.

• Do not operate the power tool near ammable

materials. Sparks could ignite these materials.

• Do not use accessories that require liquid cool-

ants. Using water or other liquid coolants may result

in electrocution or shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other acces-

sory. Pinching or snagging causes rapid stalling of the

rotating accessory which in turn causes the uncon-

trolled power tool to be forced in the direction opposite

of the accessory’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel that

is entering into the pinch point can dig into the surface

of the material causing the wheel to climb out or kick

out. The wheel may either jump toward or away from

the operator, depending on direction of the wheel’s

movement at the point of pinching. Abrasive wheels

may also break under these conditions.

Kickback is the result of power tool misuse and/or in-

correct operating procedures or conditions and can be

avoided by taking proper precautions as given below.

• Maintain a rm grip on the power tool and posi-

tion your body and arm to allow you to resist

kickback forces. Always use auxiliary handle, if

provided, for maximum control over kickback or

torque reaction during start-up. The operator can

control torque reactions or kickback forces, if proper

precautions are taken.

• Never place your hand near the rotating acces-

sory. Accessory may kickback over your hand.

• Do not position your body in the area where power

tool will move if kickback occurs. Kickback will

propel the tool in direction opposite to the wheel’s

movement at the point of snagging.

• Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the ac-

cessory. Corners, sharp edges or bouncing have a

tendency to snag the rotating accessory and cause

loss of control or kickback.

• Do not attach a saw chain woodcarving blade or

toothed saw blade. Such blades create frequent

kickback and loss of control.

Safety Warnings Specic for Grinding and Abra-

sive Cutting-O󰀨 Operations:

• Use only wheel types that are recommended for

your power tool and the specic guard designed

for the selected wheel. Wheels for which the power

tool was not designed cannot be adequately guarded

and are unsafe.

• The grinding surface of centre depressed wheels

must be mounted below the plane of the guard lip.

An improperly mounted wheel that projects through the

plane of the guard lip cannot be adequately protected.

• The guard must be securely attached to the power

tool and positioned for maximum safety, so the

least amount of wheel is exposed towards the

operator. The guard helps to protect the operator

from broken wheel fragments, accidental contact with

wheel and sparks that could ignite clothing.

• Wheels must be used only for recommended

applications. For example: do not grind with the

side of cut-o󰀨 wheel. Abrasive cut-o󰀨 wheels are

intended for peripheral grinding, side forces applied

to these wheels may cause them to shatter.

• Always use undamaged wheel anges that are of

correct size and shape for your selected wheel.

Proper wheel anges support the wheel thus reducing

the possibility of wheel breakage. Flanges for cut-o󰀨

wheels may be di󰀨erent from grinding wheel anges.

Produktspezifikationen

Marke:	Milwaukee
Kategorie:	Sander
Modell:	6142-31

Brauchst du Hilfe?

Wenn Sie Hilfe mit Milwaukee 6142-31 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Sander Milwaukee

Milwaukee M18 BOS125 Bedienungsanleitung

31 August 2024

Milwaukee 6142-31 Bedienungsanleitung

5 August 2024

Milwaukee 2648-20 Bedienungsanleitung

4 August 2024

Milwaukee M18 2648-21 Bedienungsanleitung

29 Juli 2024

Bedienungsanleitung Sander

Neueste Bedienungsanleitung für -Kategorien-

Hilti DWS 225 Bedienungsanleitung

15 Oktober 2024

Matrix BS 600 Bedienungsanleitung

8 Oktober 2024

Black And Decker RO410 Bedienungsanleitung

7 Oktober 2024

Black And Decker BT300 Bedienungsanleitung

5 Oktober 2024

Gamma HS200W Bedienungsanleitung

5 Oktober 2024

Gamma IB-350W Bedienungsanleitung

4 Oktober 2024

Gamma HPS-200W Bedienungsanleitung

4 Oktober 2024

Black And Decker FS1000 Bedienungsanleitung

4 Oktober 2024

Powerplus POWE40010 Bedienungsanleitung

3 Oktober 2024

Hazet 9032 MK Bedienungsanleitung

1 Oktober 2024