Milwaukee 48-22-2165 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Milwaukee 48-22-2165 (7 Seiten) in der Kategorie Tang. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/7
Cat. No. / No de cat.
48-22-2165
PUNCHDOWN TOOL
OUTILS D'INSERTION
HERRAMIENTA PARA PONCHADORA
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
2
IMPORTANT SAFETY INSTRUCTIONS
4
Removing Blade
Rotate the blade a quarter turn counter-clockwise
and pull blade out to remove.
OPERATION
Using LED Light
WARNING
To reduce the risk of injury, do not
look directly into the light when the
light is on.
Press the power button to turn the light on or off.
NOTE: After 15 minutes of continuous use, the light
will shut off automatically.
NOTE: The LED will ash three (3) times to indicate
low batteries. This will continue each time the power
button is turned on until the batteries are replaced.
Adjusting Force
1. To set the force to LO, push the HI/LO switch to
the left.
2. To set the force to HI, push the HI/LO switch to
the right.
Force
Setting
66 Panel/Block/
Terminal
110 Cross-Connect
Panels/Blocks/
Keystone Jacks
LO 24-26 gauge
conductors
All
HI 23 and larger
gauge
connectors
NOT
RECOMMENDED
110 Type Punchdown
1. Insert the 110 type blade into
B
568
B
A
B
4687
A
the tool.
2. -Select the proper force set
ting by referring to the above
table.
3. Lay the wires in the wire
slots.
B
A
B
568
B
A
4687
4. Place the blade into the wire
slot. Make sure the CUT side
of the blade faces the end of
the wire to be cut.
5. Push down on the back end of
the tool with the palm of your
hand until impact.
6. Remove the blade from the
wire slot. Make sure the wire
is properly seated in the bot-
B
A
B
568
B
A
4687
tom of the wire slot between
the insulation displacement
connector's (IDC) blades.
66 Type Punchdown
1. Insert the 66 type blade into
the tool.
2. Select the proper force
setting by referring to the
above table.
3. Lay the wires in the post
openings.
4. Place the blade into the wire
post. Make sure the CUT side
of the blade faces the end of
the wire to be cut.
5. Push down on the back end of
the tool with the palm of your
hand until impact.
6. Remove the blade from the
wire post. Make sure the wire
is properly seated at the bot-
tom of the post between the
insulation displacement connector's (IDC) blades.
MAINTENANCE
WARNING
To reduce the risk of injury, always
remove the battery before perform-
ing any maintenance. Never disassemble the tool.
Contact a MILWAUKEE service facility for ALL
repairs.
Maintain Tool
Keep your tool in good repair by adopting a regular
maintenance program. If the tool does not work
properly, return the light to a MILWAUKEE service
facility for repairs.
WARNING
To reduce the risk of personal in-
jury and damage, never immerse
your tool in liquid or allow a liquid to ow inside
them.
Cleaning
Keep tool handles clean, dry and free of oil or grease.
Use only mild soap and a damp cloth to clean the tool
since certain cleaning agents and solvents are harmful
to plastics and other insulated parts. Some of these
include gasoline, turpentine, lacquer thinner, paint
thinner, chlorinated cleaning solvents, ammonia and
household detergents containing ammonia. Never
use ammable or combustible solvents around tools.
ACCESSORIES
WARNING
Only use accessories speciîš¿cally
recommended for this tool. Others
may be hazardous.
Cat. No. Description
48-22-2166 Extended Reach 110 Punchdown
Blade
48-22-2167 110/66 Combination Punchdown
Blade
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a local distributor.
SERVICE - UNITED STATES
1-800-SAWDUST (1.800.729.3878)
Produktspezifikationen
| Marke: | Milwaukee |
| Kategorie: | Tang |
| Modell: | 48-22-2165 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Milwaukee 48-22-2165 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Tang Milwaukee
2 August 2024
Bedienungsanleitung Tang
- Tang 3M
- Tang Scarlett
- Tang Leatherman
- Tang StarTech.com
- Tang Neutrik
- Tang Gefen
- Tang Extron
- Tang Valueline
- Tang Weidmüller
- Tang Dataflex
- Tang PureLink
Neueste Bedienungsanleitung für -Kategorien-
22 September 2024
5 September 2024
5 September 2024
5 September 2024
5 September 2024
29 August 2024
29 August 2024
29 August 2024
29 August 2024
29 August 2024