Milwaukee 2610-24 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Milwaukee 2610-24 (13 Seiten) in der Kategorie bohren. Dieser Bedienungsanleitung war für 27 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/13
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S
MANUAL.
AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN
COMPRENDRE LE MANUEL DE L'UTILISATEUR.
PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL
MANUAL DEL OPERADOR.
18 V 1/2" HAMMER-DRILL AND DRIVER DRILL
PERCEUSE À PERCUSSION ET PERCEUSE-VISSEUSE DE 18 V 13 mm (1/2")
TALADRO DE PERCUSIÓN Y TALADRO ATORNILLADOR DE 13 mm (1/2") 18 V
Cat. No.
No de cat.
2610-20
2611-20
23
PERSONAL SAFETY
GENERAL POWER TOOL SAFETY WARNINGS
WORK AREA SAFETY
ELECTRICAL SAFETY
• Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of fl ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodifi ed plugs and matching outlets will
reduce risk of electric shock.
• Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase
the risk of electric shock.
• Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk
of electric shock.
• If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
• Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
• Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
• If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
• Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
• Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
• Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
• Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits
etc., in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
• Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the infl uence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
• Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
• Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your fi nger on the switch or energising power tools
that have the switch on invites accidents.
• Recharge only with the charger specifi ed by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fi re
when used with another battery pack.
BATTERY TOOL USE AND CARE
WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS.
Failure to follow the warnings and instructions may result in electric shock, fi re and/or
serious injury. Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
45
SPECIFIC SAFETY RULES
• Use power tools only with specifi cally desig-
nated battery packs. Use of any other battery
packs may create a risk of injury and fi re.
• When battery pack is not in use, keep it away
from other metal objects like paper clips,
coins, keys, nails, screws, or other small metal
objects that can make a connection from one
terminal to another. Shorting the battery termi-
nals together may cause burns or a fi re.
• Under abusive conditions, liquid may be eject-
ed from the battery; avoid contact. If contact
accidentally occurs, fl ush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
SERVICE
• Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
FUNCTIONAL DESCRIPTION SYMBOLOGY
SPECIFICATIONS
Direct Current
Underwriters Laboratories, Inc.
United States and Canada
No Load Revolutions per
Minute (RPM)
ASSEMBLY
WARNING Recharge only with the
charger specifi ed for the battery. For
specifi c charging instructions, read the opera-
tor’s manual supplied with your charger and
battery.
Inserting/Removing the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
To insert the battery, slide the pack into the body of
the tool. Make sure it latches securely into place.
Cat. No.
Volts
DC
No Load
RPM
No Load Blows
per Minute
Capacities
Steel Flat Bit Auger Bit Hole Saw Screws (dia.) Masonry
2610-20
2611-20
18
18
Low 0-450
High 0-1800
Low 0-450
High 0-1800
n/a
Low 0-7200
High 0-28,800
1/2”
1/2”
1-1/2”
1-1/2”
1”
1”
2-1/8”
2-1/8”
1/4”
1/4”
n/a
5/8”
1. Trigger
2. Control switch
3. LED
4. Keyless chuck
5. Torque selector collar
6. Application selector
collar
7. Speed selector
8. Side handle
1
28
4
67
5
3
WARNING Always remove battery
pack before changing or removing ac-
cessories. Only use accessories specifi cally
recommended for this tool. Others may be
hazardous.
OPERATION
WARNING Always remove battery
pack before changing or removing ac-
cessories. Only use accessories specifi cally
recommended for this tool. Others may be
hazardous.
WARNING To reduce the risk of injury,
wear safety goggles or glasses with side
shields.
Installing the Side Handle
1. To install the side handle, loosen the side handle
grip until the hooks are far enough apart to fi t into
the slots on the gear case ring. The side handle
can be positioned on the top, left, or right side
of the tool. Tighten the side handle grip until it is
secure.
2. To remove the side handle, loosen the side
handle grip until the side handle can be removed.
Reposition and tighten securely.
Using Keyless Chucks
This tool is equipped with a spindle lock. The chuck
can be tightened with one hand, creating higher grip
strengths on the bit.
Always remove the battery pack or lock the trigger
before inserting or removing bits.
1. To open the chuck jaws, turn the sleeve in the
counterclockwise direction.
When using drill bits, allow the bit to strike the
bottom of the chuck. Center the bit in the chuck
jaws and lift it about 1/16" off of the bottom.
When using screwdriver bits, insert the bit far
enough for the chuck jaws to grip the hex of the
bit.
2. To close the chuck jaws, turn the sleeve in the
clockwise direction. The bit is secure when the
chuck makes a ratcheting sound and the sleeve
can not be rotated any further.
3. To remove the bit, turn the sleeve in the coun-
terclockwise direction.
NOTE: A ratcheting sound may be heard when the
chuck is opened or closed. This noise is part of the
locking feature, and does not indicate a problem
with the chuck’s operation.
Selecting Speed
The speed selector is on top of the motor housing.
Allow the tool to come to a complete stop before
changing speeds. See “Applications” for recom-
mended speeds under various conditions.
1. For Low speed (up to 450 RPM), push the speed
selector to display “1”.
2. For High speed (up to 1800 RPM), push the
speed selector to display “2”.
Fig. 1 Hooks
Slots
WARNING To reduce the risk of injury,
always use a side handle when using this
tool. Always brace or hold securely. Ensure
side handle is tightened securely before
each use.
Fig. 3
To Drill
Fig. 2
To Hammer
Selecting Hammer, Drill or Drive Action
MILWAUKEE Hammer-Drills have three operat-
ing modes: drilling with hammering action, drilling
only, and driving screws. MILWAUKEE Driver Drills
have two operating modes: drilling only and driving
screws. To set the operating mode, rotate the ap-
plication selector collar and torque selector collar
to the desired symbols.
1. To use the hammer-drilling mode (Cat. No.
2611-20 only), rotate the application selector
collar until the hammer symbol appears in
line with the arrow. Apply pressure to the bit to
engage the hammering mechanism.
NOTE: The number selected on the torque collar
has no effect on operation of the drill in hammer
mode. NOTE: When using carbide bits, do not
use water to settle dust. Do not attempt to drill
through steel reinforcing rods. This will damage
the carbide bits.
2. To use the drilling only mode, rotate the ap-
plication selector collar until the drill symbol
appears in line with the arrow.
NOTE: The number selected on the torque collar
has no effect on operation of the drill in drilling
mode.
• Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
• Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
• Hold power tool by insulated gripping surfaces,
when performing an operation where the cut-
ting accessory may contact hidden wiring or its
own cord. Cutting accessory contacting a “live” wire
may make exposed metal parts of the power tool
“live” and could give the operator an electric shock.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
• WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are spe-
cially designed to fi lter out microscopic particles.
Produktspezifikationen
| Marke: | Milwaukee |
| Kategorie: | bohren |
| Modell: | 2610-24 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Milwaukee 2610-24 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung bohren Milwaukee
8 Oktober 2024
1 Oktober 2024
13 September 2024
13 September 2024
11 September 2024
10 September 2024
8 September 2024
3 September 2024
3 September 2024
3 September 2024
Bedienungsanleitung bohren
- bohren Basetech
- bohren Panasonic
- bohren Clas Ohlson
- bohren Cotech
- bohren Makita
- bohren Bosch
- bohren Flex
- bohren Laserliner
- bohren Parkside
- bohren Vonroc
- bohren AEG
- bohren Velleman
- bohren Powerfix
- bohren Black And Decker
- bohren Cocraft
- bohren FERM
- bohren Ryobi
- bohren Skil
- bohren Topcraft
- bohren Trotec
- bohren Maestro
- bohren Baier
- bohren Carat
- bohren Eibenstock
- bohren Hilti
- bohren Bort
- bohren DeWalt
- bohren Einhell
- bohren Elu
- bohren Festool
- bohren Mafell
- bohren Maktec
- bohren Worx
- bohren Luxor
- bohren Hikoki
- bohren Hitachi
- bohren Hyundai
- bohren Hazet
- bohren Kinzo
- bohren Kress
- bohren Max
- bohren Metabo
- bohren Stanley
- bohren Würth
- bohren Güde
- bohren Power Craft
- bohren Scheppach
- bohren Workzone
- bohren Biltema
- bohren Meec Tools
- bohren Dremel
- bohren Fieldmann
- bohren EcoMAC
- bohren Proxxon
- bohren Westfalia
- bohren Dedra
- bohren DURO
- bohren Graphite
- bohren Silverline
- bohren Holzmann
- bohren MSW
- bohren Huvema
- bohren Robust
- bohren Zipper
- bohren Stomer
- bohren Yato
- bohren Baumr-AG
- bohren Genesis
- bohren BluCave
- bohren Toolland
- bohren Delta
- bohren Batavia
- bohren Bavaria
- bohren Brüder Mannesmann
- bohren Narex
- bohren Toolcraft
- bohren Fein
- bohren Verto
- bohren Craftsman
- bohren Powerplus
- bohren Rupes
- bohren ProfiTech
- bohren Alpha Tools
- bohren Ozito
- bohren Kawasaki
- bohren Sun Joe
- bohren Ridgid
- bohren Porter-Cable
- bohren VARO
- bohren Duro Pro
- bohren Economy
- bohren Fe Powertools
- bohren Gamma
- bohren Global
- bohren Goon
- bohren Lux Tools
- bohren Max Bahr
- bohren Protool
- bohren Spit
- bohren Steren
- bohren Tanaka
- bohren Meister Craft
- bohren Malmbergs
- bohren Truper
- bohren RIKON
- bohren Kreg
- bohren G-Technology
- bohren Einhell Bavaria
- bohren Powerblade
- bohren Rok
- bohren Tryton
- bohren MyTool
- bohren McKenzie
- bohren Rodcraft
- bohren Ribimex
- bohren Black Decker
- bohren RUKO
- bohren Handwerk
- bohren Stalco
Neueste Bedienungsanleitung für -Kategorien-
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
15 Oktober 2024
15 Oktober 2024
13 Oktober 2024
13 Oktober 2024
13 Oktober 2024