Milwaukee 1675-1 Bedienungsanleitung

Milwaukee Andere 1675-1

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Milwaukee 1675-1 (13 Seiten) in der Kategorie Andere. Dieser Bedienungsanleitung war für 8 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/13

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S

MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN

COMPRENDRE LE MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL

MANUAL DEL OPERADOR.

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

HEAVY-DUTY HOLE HAWG®

FOREUSE EXTRA-ROBUSTE HOLE HAWG®

TALADRO HEAVY-DUTY HOLE HAWG®

Catalog No.

No de Cat.

1670-1

1675-1

1675-6

1676-6

SPECIFICATIONS

Steel Capacity Wood Capacity

Cat. No. Volts

AC Speed No Load

RPm Twist Bit Auger Bits Ship Auger

Bits Selfeed Bit

1670-1

1675-1

1675-6

1676-6

120

High

Low

High

Low

High

Low

900

1200

300

1200

300

1200

300

7/16"

5/16"

1/2"

5/16"

1/2"

5/16"

1/2"

1-1/2"

1-1/8"

1-1/2"

1-1/8"

1-1/2"

1-1/8"

1-1/2"

1-1/4"

1-1/2"

1-1/4"

1-1/2"

1-1/4"

1-1/2"

2-9/16"

1-3/8"

4-5/8"

1-3/8"

4-5/8"

1-3/8"

4-5/8"

Amps

Volts

Alternating Current Only

No Load Revolutions

per Minute (RPM)

CUS Underwriters Laboratories, Inc.

United States and Canada

Mexican Approvals Marking

SYMBOLOGY

FUNCTIONAL DESCRIPTION

1. Spade Handle

2. Chuck

3. Trigger Switch

4. Reversing Switch

5. Switch Handle

6. Motor Housing

7. Gear Shift Lever

8. Pipe Handle

9. Insulated Gripping

Surfaces

PERSONAL SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WORK AREA SAFETY

ELECTRICAL SAFETY

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power tools in explosive atmos-

pheres, such as in the presence of ﬂ ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁ ed plugs and matching outlets will

reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase

the risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use

of a cord suitable for outdoor use reduces the risk

of electric shock.

• If operating a power tool in a damp location is

unavoidable, use a ground fault circuit inter-

rupter (GFCI) protected supply. Use of an GFCI

reduces the risk of electric shock.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

• Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

• If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS. Failure

to follow the warnings and instructions may result in electric shock, ﬁ re and/or serious

injury. Save all warnings and instructions for future reference. The term "power

tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

• Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must

be repaired.

• Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such pre-

ventive safety measures reduce the risk of starting

the power tool accidentally.

• Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

• Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power tool

for operations different from those intended could

result in a hazardous situation.

• Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inﬂ uence of drugs, alcohol or medi-

cation. A moment of inattention while operating

power tools may result in serious personal injury.

• Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

• Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your ﬁ nger on the switch or energising power tools

that have the switch on invites accidents.

SERVICE

• Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

SPECIFIC SAFETY RULES

• Use auxiliary handle(s), if supplied with the

tool. Loss of control can cause personal injury.

• Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its

own cord. Cutting accessory contacting a “live”

wire may make exposed metal parts of the power

tool “live” and could give the operator an electric

shock.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing,

contact a MILWAUKEE service facility for a free

replacement.

• WARNING Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to cause

cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and

other masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well

ventilated area, and work with approved safety

equipment, such as those dust masks that are spe-

cially designed to ﬁ lter out microscopic particles.

Fig. B Fig. C

Fig. A

GROUNDING

WARNING Improperly connecting the

grounding wire can result in the risk of elec-

tric shock. Check with a qualiﬁ ed electrician

if you are in doubt as to whether the outlet is

properly grounded. Do not modify the plug

provided with the tool. Never remove the

grounding prong from the plug. Do not use

the tool if the cord or plug is damaged. If

damaged, have it repaired by a MILWAUKEE

service facility before use. If the plug will not

ﬁ t the outlet, have a proper outlet installed by

a qualiﬁ ed electrician.

Grounded Tools: Tools with Three Prong Plugs

Tools marked “Grounding Required” have a three

wire cord and three prong grounding plug. The

plug must be connected to a properly grounded

outlet (See Figure A). If the tool should electrically

malfunction or break down, grounding provides a

low resistance path to carry electricity away from

the user, reducing the risk of electric shock.

The grounding prong in the plug is connected

through the green wire inside the cord to the

grounding system in the tool. The green wire in the

cord must be the only wire connected to the tool's

grounding system and must never be attached to

an electrically “live” terminal.

Your tool must be plugged into

an appropriate outlet, properly

installed and grounded in accord-

ance with all codes and ordinances.

The plug and outlet should look like

those in Figure A.

Double Insulated Tools:

Tools with Two Prong Plugs

Tools marked “Double Insulated” do not require

grounding. They have a special double insula-

tion system which satisﬁ es OSHA requirements

and complies with the applicable standards of

Underwriters Laboratories, Inc.,

the Canadian Standard Asso-

ciation and the National Elec-

trical Code. Double Insulated

tools may be used in either of

the 120 volt outlets shown in

Figures B and C.

Grounded tools require a three wire extension

cord. Double insulated tools can use either a two

or three wire extension cord. As the distance from

the supply outlet increases, you must use a heavier

gauge extension cord. Using extension cords with

inadequately sized wire causes a serious drop in

voltage, resulting in loss of power and possible tool

damage. Refer to the table shown to determine the

required minimum wire size.

The smaller the gauge number of the wire, the

greater the capacity of the cord. For example, a 14

gauge cord can carry a higher current than a 16

gauge cord. When using more than one extension

cord to make up the total length, be sure each cord

contains at least the minimum wire size required.

If you are using one extension cord for more than

one tool, add the nameplate amperes and use the

sum to determine the required minimum wire size.

Guidelines for Using Extension Cords

• If you are using an extension cord outdoors, be

sure it is marked with the sufﬁ x “W-A” (“W” in

Canada) to indicate that it is acceptable for outdoor

use.

• Be sure your extension cord is properly wired

and in good electrical condition. Always replace a

damaged extension cord or have it repaired by a

qualiﬁ ed person before using it.

• Protect your extension cords from sharp objects,

excessive heat and damp or wet areas.

READ AND SAVE ALL

INSTRUCTIONS FOR FUTURE USE.

* Based on limiting the line voltage drop to ﬁ ve volts at

150% of the rated amperes.

EXTENSION CORDS

Recommended Minimum Wire Gauge

For Extension Cords*

Extension Cord Length

Nameplate

Amperes 25' 50' 75' 100' 150'

0 - 2.0

2.1 - 3.4

3.5 - 5.0

5.1 - 7.0

7.1 - 12.0

12.1 - 16.0

16.1 - 20.0

ASSEMBLY

Installing Bits into Keyed Chucks

1. Unplug tool.

2. Open the chuck jaws

wide enough to insert

the bit. Be sure the bit

shank and chuck jaws

are clean. Dirt particles

may prevent the bit from

lining up properly.

3. Insert the bit into the

chuck. Center the bit in

the chuck jaws and lift it about 1/16" off of the

bottom. Tighten the chuck jaws by hand to align

the bit.

4. Place the chuck key in each of the three holes in

the chuck, turning it clockwise. Tighten securely.

5. To remove the bit, insert the chuck key into one

of the holes in the chuck and turn it counterclock-

wise.

Bit Selection

• Use sharp bits. Sharp bits are less likely to bind

when drilling.

• Use the proper bit for the job. There are many

types of bits designed for speciﬁ c purposes. Check

the information on the bit's packaging for proper

usage.

• Do not use bits larger than the rated capacity of the

drill. Gear damage or motor overload may result.

Pipe Handle

The pipe handle may be used on either side of the

tool. Thread pipe handle into one of the threaded

holes in the motor housing.

Spade Handle

The spade handle can be

attached to the tool in three

positions. Remove the hex

head screws which secure

the handle. Remove the han-

dle and move it to the desired

position. To mount the handle

in position C, it is necessary

to reverse the mounting holes

by turning the handle around.

Fig. 2

Bit binding

WARNING To reduce the risk of injury,

wear safety goggles or glasses with side

shields.

WARNING To reduce the risk of injury,

always unplug tool before attaching or remov-

ing accessories or making adjustments. Use

only speciﬁ cally recommended accessories.

Others may be hazardous. WARNING To reduce the risk of

personal injury when drilling, hold tool by in-

sulated gripping surfaces when performing an

operation where the cutting tool may contact

hidden wiring or its own cord. Contact with a

"live" wire will make exposed metal parts of

the tool "live" and shock the operator.

WARNING When drilling with a single

speed drill or in HI with a two speed drill,

always hold the drill securely using the pipe

handle, or brace the drill against a solid ﬁ xed

object in preparation for a sudden reaction.

When drilling in LO with a two speed drill,

always brace the drill against a solid ﬁ xed

object in preparation for a sudden reaction.

When drilling, never use your body to brace

drill.

Never put your hands (or other body parts)

between the part of the drill being braced and

the object it is being braced against. Hands

(or other body parts) that are in the path of the

reaction can be pinched, crushed and broken.

If the bit binds, the drill will suddenly react in the

opposite direction of the rotation of the bit. Figure

3 shows the path of reaction (B) if the drill bit binds

while being driven in forward (A). The operator

should reduce the chances of a sudden reaction

by following the instructions listed below.

OPERATION

Fig. 3

Produktspezifikationen

Marke:	Milwaukee
Kategorie:	Andere
Modell:	1675-1

Brauchst du Hilfe?

Wenn Sie Hilfe mit Milwaukee 1675-1 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Andere Milwaukee

Milwaukee C12 FM Bedienungsanleitung

22 August 2024

Milwaukee C12 PC Bedienungsanleitung

17 August 2024

Milwaukee M12DE-151C Bedienungsanleitung

7 August 2024

Milwaukee M18 BMS20 Bedienungsanleitung

5 August 2024

Milwaukee 1675-1 Bedienungsanleitung

3 August 2024

Milwaukee C12 PPC -PEX Bedienungsanleitung

31 Juli 2024

Milwaukee M12DE-201C Bedienungsanleitung

25 Juli 2024

Bedienungsanleitung Andere

Neueste Bedienungsanleitung für -Kategorien-

Einhell BG-WW 1355 NN Bedienungsanleitung

15 Oktober 2024

Einhell BG-CS 235 E Bedienungsanleitung

15 Oktober 2024

Parkside IAN 93483 Overig Bedienungsanleitung

27 September 2024

Parkside IAN 78962 Overig Bedienungsanleitung

27 September 2024

Vonroc S-GG502DC Bedienungsanleitung

23 September 2024

Gamma SRG-00057A Bedienungsanleitung

23 September 2024

Stanley FMC700 Bedienungsanleitung

23 September 2024

Ferrex SF5040E Bedienungsanleitung

20 September 2024

Xenteq SBP-SERIES Bedienungsanleitung

17 September 2024

Ferrex FAM 20-i - 5420033 Bedienungsanleitung

16 September 2024